2004 DACIA SUPERNOVA ECO mode

82A
HORN - ENGINE IMMOBILISER
82A - 20
D)
Memorising of the new code of the injection computer
- in ACTUATORS
launch the command MANUAL INTRODUCTION CODE ; type
the repairing code of the old key kit, then validate it with the key
ENTER.
- the message “COMMAND IN PROGRESS ” will be displayed followed by the message
“FINISHED COMMAND ”.
-s et the contact on; t he anti starting LED indicator will start blinking, then take off the
contact;
-set the c ontact on for 10 seconds ; take off the contact;
- check if the engine starts with the two keys.
If the engine doesn’t start, repeat this operation (point D).
E) Key resynchronisation (remote controls)
-if the vehicle is equipped with only one remote control, its resynchronisation will be
performed as follows (simple resynchronisation);
- with t he contact taken off, push continuously on the c entra l l ocking but ton from the
dashboard, up to the moment the anti starting LED indicator remains lighted (the doors actuators
are performing a closing/opening course.) From this moment, t he operator has 10 seconds to
perform the next operation; - push twice on the remote control (the doors actuators are performing a closing/opening
course.) and the anti starting LED indicator turns off; - if the vehicle is equipped with two remotes controls, perform the simple resynchronisatio n
procedure for the first key and a specific resynchronisation procedure for the second key, with
the CLIP tester as follows: - in COMPUTER TEST select ANTISTARTING with t he c ontact t aken off, then
COMMAND MODE , CONFIGURATION ; launch the command PROGRAMMING OF
THE SECOND TIR/TIE KEY and validate (the doors actuators are performing a closing/
opening course.). Then within 10 seconds, push twice on the remote control (the doors actuators
are performing a closing/o pening course).DIAGNOSTIC
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 39
THE CONFORMITY CHECKING
Next, the checking of different states and configurations of the anti starting system is to be
performed.
In case of finding some failures at the diagnostic by means of
RECOMMENDATION the CLIP tester, analyse them based on the diagnostic (ALP)
corresponding to the respective failure.
Nr.
crt.Function State / configuration Observ
at i ons
1. Conformity E.C.U decoder Computer identification Display of the E.C.U.
decoder item
2. Remote control type 2G = remote control IR = infrared configuration RF = radio frequency
3. Dome ceiling Without dome ceiling or Validation on the blue button
with dome ceiling on CLIP screen
4. Key programming 3G = configuration key With one or 2 keys
programming
5. Configuration petrol/ diesel 3D = configuration coded Without = for petrol engine dies el electric valve With = for diesel engine
6. Forced starting protection 9D = forced protecting mode ACTIVE = only after
validation on the blue button
7. Anti starting state 10G = anti starting ACTIVE = with the contact
taken off or after 10 seconds
from the co ntact taken off
8. Key presence 8D = key present ACTIVE at the setting on the
c ontact if there is a coded key.
NOTE: the states 8D, 9D,
10 D must be ACTIVE at a
co rrec t operation
9. Code key receiving 9D = received key code ACTIVE at the setting on the
contact if the key is coded in
a good format
10 . Correct key code 10D = right key code ACTIVE at the setting on the
contact if the key is coded in
a good format and has the
correct code.
NOTE: after the analyse of the states 8D, 9D, 10 D the
co ntact will be set o when
the LED indicator blinks
(
ACTIVE anti starting)
DIAGNOSTIC
vnx.su

82B
HORN - ENGINE IMMOBILISER
82B - 43
THE PIN CODE
The PIN code is formed of four figures and it can be used only for deactivating the anti intrusion
s ystem, if this operation can not be performed by pushing the deactivating button from the RF
remote control of the vehicle. For introducing the PIN code, perform as follows:-set on the contact key in the M position and take it off it for three times in seven seconds,
after which the anti intrusion LED indicator will switch on for three seconds; -set on the contact again on the M position and maintain it until the number of the L ED
blinks is e qual with the first figure of the PIN code, then take off the contact; -set on the contact in the M position and maintain it until the number of LED blinks is equal
w ith the second figure of the PIN code, then take off the contact;
-perform the above mentioned method in order to introduce the third and the fourth figure
of the PIN code;
-after that, the system is deactivated and the siren stops automatically;
- set on the contact again – the anti LED indicator must switch on, confirming in this way
that the c orrect introduction of the PIN code.
AT TENT ION
If it i s necessary the checking of the PIN code, t his will be pe rformed
only after al least 20 seconds have passed, since the anti intrusion ECU has been
connected to the vehicle’s wiring or since the connecting of t he vehicle’s battery.
The COBRA anti intrusion system can operate in t hree different modes (2,3 or 4).
For the Super Nova vehicles, the system has been programmed to work in the second operation
mode. If by mistake the PIN code was introduced in less than 20 seconds since the battery
connecting or since connecting the anti intrusion ECU, this can involve the change of the operation
way of the system, which will generate errors during the operation. There is, although, the possibility
of reprogramming the correct operation way (type 2) and in this purpose, perform the following
operations : - disconnect and then reconnect the anti intrusion ECU; when connecting the anti intrusion
ECU the anti intrusion LED indicator will switch on once, confirming the correct connecting;
-af ter at least 5 seconds from the previous operation, but no more than 20 second from it,
perform the following operation s:
-s et on the contact key in the M position for three times and then release it;
- the anti intrusion LED indicator will switch on for three seconds and then will switch off;
- set on again the contact key in the “M” position and maintain it, counting two blinks of the
anti intrusion LED indicator, then take off the contact;
- the LED indicator will blink for two times in two series, confirming in this way the proper
performance of the previous operations;
press the doors locking button of the dashboard, in order to lock and unlock the doors; the anti
intrusion LED indicator must not blink;
vnx.su

86
RADIO
GENERAL
C ode protection
T he radio is protected by means of a four digit code. This code is introduced by the
radio keys at each battery disconnection.
Co de introduction by means of the radio keys : in order to valid one digit introduction,
push the next key ( see the operation technical book).
In case of a wrong code, the instrument is getting blocked ( one minute for the first error, two
minutes for the second error, four minutes for the third…)
Af ter first code introduction, some confi gurations must be programmed ( see chapter”
configuration”). These are remaining programmed till battery disconnection.
NOTE : the return to the “wave jammer” mode is possible by simultaneously push-
ing of the keys 2 and 5, putting the radio under tension. Wait then for two minutes.
Programming
OBSERVATION : in order to select the radio operation are a, push simultaneously keys 2
and 5, putting the radio under tension. Wait then for about two minutes. Introduce the four digits
code, then:
-s elect the adequate area
86 - 2
25
-America
-Japab
-Asia
-Arabia
-Othe rs (Europa, Africa, others…)
-Select the sound tonality curves:
- 0 : inactive adjustment
- 1 : Tw i n g o
- 2 : Clio
- 3 : Mégane
- 4 : Laguna
- 5 :
T op ra nge
- speakers number configura tion – with or
w ithout rear speakers (REAR ON / OFF)
NOTE : it is not necessary to perform the configuration after radio code introduction,
further to a supply failure.
vnx.su