2004 DACIA SOLENZA Canister

IGNITION AND INJECTION
17
17 - 4
Injection system
CHARACTERISTICS
• Electronic control unit (UCE injection) with 90 pins SIEMENS.
• Sequential multi-poin t injection.
• Controlling one injector each time.
• Static ignition with a double ignition coil.
• Canister purging valve controlled in opening duty cycle.
• Idling regime correction subject to:
- climate maintenance (air conditioning);
- battery voltage.
• Maxima l regime:
- 6200 rot/min for first, second and third speed;
- 6000 rot/min for fourth and fifth speed.
vnx.su

IGNITION AND INJECTION
17
17 - 5
ELEMENTS LOCATION
1. RPM sensor ( tightening moment : 0.8 daNm);
2. Water temperature sensor (tightening moment: 2.5 daNm);
3. Atmospheric pressure sensor;
4. Step-by-step engine for idling adjustment;
6. Air temperature sensor;
7. UCE injection;
8. Choke sensor;
9. Fuse and relays box;
10. Air filter;
11 .D etonation sensor (tightening moment: 2.5 daNm);
12. Oxygen sensor (tightening moment: 4.5 daNm);
13. Ignition coil;
14. Carbon canister with purging valve included;
15. Power steering pressure controller(tightening moment: 1.2 daNm);
16. Air conditioning pressure controller (tightening moment: 0.8 daNm).
Injection system
13 10 11 5 4 6 3 2 1 8 9
14 1 6 15 12 7
vnx.su

IGNITION AND INJECTION
17
17 - 7
Injection system
In the fuse box located in the engine compartment, the following relays may be identified:
A. Co mpressor relay
B. Engine c ooling fan relay, step I
C. Engine cooling fan relay, step II
D. UCE injection relay, canister-purging valve
E. Fog projectors relay
H. Fuel pump and ignition coil relay
14. C arbon canister with purging valve
included
;
16.
Power steering pressure controller; 12.
Oxygen sensor;
15.
A ir conditioning pressure controller.
1
15
12
1614
vnx.su

IGNITION AND INJECTION
17
17 - 20
DIAGNOSTIC CONDI T IONS
If wh en setting on the contact, with stopped engine, one of the following conditions is accom-
plished: -air temperature, red by the air temperature sensor, is not situated between –6° and 119°C.
-w ater temperature, red by the water temperature sensor, is not situated between –6° and
119°C.
-atmosphe ric pressure is under 775mbar,
then the OBD diagnostics are not authorized until the next contact setting on. In order to have a correct operation of the OBD diagnostic system, no electric failure of the
injection system must exist, even if the lighting of the OBD indicator is not established. The catalyst and oxygen sensor diagnostics can not be performed in the same time, but one
after other.
When the catalyst or oxygen sensor diagnostics are under operation, the canister purging valve
is closed, and the adaptive values are “blocked” at the last existent value prior to a.m. diagnostics
starting. TESTS PERFORMING LOGIC
-Solve fa ilures of electric nature.
-Erase a ll failures by means of the CLIP tester
-Perform the “teaching” stage of all adaptive values by the injection system (if necessary).
OB D COMPLETE ACTIVATION BY MEANS OF CLIP TESTER
-Erase all memorized failures.
-Erase the “learned” values from UCE injection if further to an intervention on an injection
system component, a disturbance of the “learned” values took place (step-by-step engine, flywheel
or RPM sensor, etc).
RETENTIONS (“LEARNINGS”) NECESSARY FOR UCEINJECT ION FOR OBD DI AGNOSTIC
〈 COUPLING/SUPPLY RATE LEARNING (state “ET014 = cylinder recognition 1” is PER-
FORMED with running engine). This is to be performed as following:
-a deceleration with “cutting” of the petrol injection in the third gear of the gearbox, be-
tween 3000-3500 rot/min for at least 2 seconds,
-a second deceleration with ”cutting” of the petrol injection in the third gear of the gearbox,
between 2400-2000 rot/min, for at least 2 seconds.
〈 MIXTURE ENRI CHING ADAPTIVE LEARNING
In order to do that, it is necessary that vehicle is running observing in the same time the pressure
ranges men tioned in the chapter “ Enriching adaptive correction”.
〈 State “ET202 = OBD diagnostic of combustion misfires taken into consideration” must be
AC TIVE.
“On Board Diagnostic” diagnostic conditions
vnx.su

IGNITION AND INJECTION
17
17 - 24
FAILURES DETECT ION
Th is diagnostic is to be performed when driving in the fourth or fifth gear, at constant speed
(about 70 Km / h ) and for a period of minimum 60 seconds.
Oxygen sensor diagnostic
Engine Gearbox ratio Speed Maximum period
(Km/h) (sec)
E7J V63-130 52
For the accomplishment of this test, during all its running period, UCE injection is inhibiting the
co ntrol function of the canister purging valve. UCE injection will issue the recommendation
” O xyg en sensors diagnostic taken into consideration”.
ATTENTION: after performing this test, t he contact settin g on is imposed (key in M
position) before reading the res ults by means of the C LIP tester. Any contact sett ing off
be fore reading the test results, will lead to their wrong interpretation.
If after test performing, the CLIP tester is noticing a failure of the oxygen sensor, refer to
the diagnostic method related to this symptom.
RE PARATION PE RFORM ING CONFIR M ATION
Check by means of the CLIP tester, the bellow states, which must have the following configu-
ration:
- ET102: Sensors diagnostic taken into consideration ------------------------ AC TIVE
- ET1 06: Sensors diagnostic performed --------------------------------------- AC TIVE
-no cata lyst failure is detected by the CLIP tester and the OBD indicator is off.(mbar) .
vnx.su

IGNITION AND INJECTION
17
17 - 32
DF014
P RESENT
OR
ME MO RIZEDCANISTER PURGING VALVE CIRCUIT
1.DEF : Open circuit or short-circuit
CO : Open circuit
CC.O : S hot circuit at mass
CC. 1 : Short circuit at + 12 V.
RECO MMENDATIONS
Conditions for diagnostic appl ication for memorized failure:
Se t the contact on or launch commend “AC016: Canister Purging Valve”
In ca se of failures additi on, treat as most important failure “DF009 actuators
relay control circuit ”.
* If the failure is memorized with OBD indicator on, check in the context part,
if state “ET117 : Canister purging control” corresponding to the OBD i ndicator
lighting request is affirma tive. In this case, proceed as per bellow mentioned
met hod.
C heck the connection and the connector state of the can ister purging valve .
C hange the connector if necessary.
C heck the resistance of the canister purging valve.
Repl ace the canister purging valve if is necessary.
C heck with the contact on, the presence of +12 Volts at pin 1 of the purging valve .
Fi x if necessary.
C onnect the 90 ways terminal box instead of the injection computer the n check the in s u la t ion and
the continuity of the l ine:
Pin 4 injection computer > pin 2 canister purging valve
Fix if necessary
Repl ace the canister purging valve if necessary.
If the problem is persisting after these checking, fix the other failures then perform the conformity
checking.
AFT ER
REPARATION Pe
rform the operations from “recommendations” for reparation confirmation.
Fi x any other possible failures.
Erase the failures memoriz ed by the injection computer.
Pe rform a conformity checking by means of the CLIP tester.
Diagnostic – Failures interpretation
vnx.su

IGNITION AND INJECTION
17
17 - 58
DF 271 ACTUATORS RELAY EXIT VOLTAGE
P RESENT 1. DEF Open circuit or short-circuit
OR
ME MO RIZED
Conditions for diagnostic appl ication at memorized failure:
Se t the conta ct off and wait until the communication with the computer
is lo st.
RECOMMEND AT IONS
REMARK : If failure “DF009 : Actuators relay control circuit” is
prese nt or memoriz ed, it must be treated as most important, because
th is could be the cause of the failure occurring.
C heck the condition of the battery and of the vehicles electric masses.
M end if necessary.
C heck the connection and condition of the actuators relay connector .
Re place the connector if necessary.
Check with the contact set on, the pr e se nce of the +12 V supply at pole 3 of th e actuators relay.
Fi x the electric routing on the line towards the corresponding fuse .
C heck with the contact set on, the presence of +12 V supply at pole 5 of the actuators relay.
Repl ace the relay if necessa ry
C heck the insu lation and continuity on the line:
Pin 66 injection computer > p ole 5 actuators relay
M end if necessary.
Disconnect one by one the elements (injector, canister purging valve…) and observe the +12 V
s upply at the exit pole 5 of the actuator s relay, in order to identify the damaged one .
Replace the damaged el ement.
P erform the operations from ” recommendations” for reparation confirma tion.
AF TER Fix any other possible failures
REPARATION Erase the failures memoriz ed by the injection computer.
Perform a conformity checking by means of the CLIP tester.
Diagnostic – Failures interpretation
vnx.su

IGNITION AND INJECTION
17
17 - 63
Diagnostic – Conformity checking
RECOMMEND AT IONS The values show n on this conformity checking are only as indication.
Performing conditions : St opped engine, contact set on.
Sequence Function Parameter / Controlled state or acti on Visualization Diagnostic
and Observations
8F uel pump AC010 : Fuel pump relay The fuel pump In case of a
must be heard problem
running consult the AC010
dia gnostic
AC271 : low speed engine blower relay The engine
9 Engine blower must
blower be heard In case of a
running with problem low speed consult the
AC272 : high speed engine blower relay The engine ET035
(if equipped) blower must(ET036)
be heard running dia gnostic with high speed
10 Idling AC014 : idling regulator Place your hand In case of a
regulator under it to feel problem
it running. c onsult
the ET 039
dia gnostic
11 Canister AC016 : canister purging valve Canister purging In case of a
purging valve valve in operation problem
consult the ET032
dia gnostic
12 Climate AC003 : Climate control compressor Compressor In case of a
control must couple problem
consult theET070
dia gnostic
13 Indicators AC212 : water temperature indicator Indicator In case of a
must be on problem
AC213 : OBD indicator Indicator consult the
must be on AC212
AC 005 : rate changing indicator (if equippe d) Indicator / DF120
must be on (ET092)
diagnostic /
diagnostics
vnx.su