2004 DACIA SOLENZA door lock

72
72 - 1
LATERAL OPENINGS TRIMS
Front door panel
DISMOUNTIN G
Disconnect the battery.
Dismount :
- window regulator crank (A) for glass
lifting , that is mounted by clips attachment on
the window regulator axle ( in case of the
vehicles provided with glass hand-drive lifting);
- attachment screw of the open ing
mechanism from inside (B), consequently the
mechanism. - locking handle (C) attached by screw.
Rotate the speaker grill (D) counter clock-
wise direction and extract it from the front door
panel.
Dismount the four attachmen t screws of the
s peaker on the door pa nel.
Disco n n ect the front door speaker
connector. Dismount the attachment screws (1 ) of the
door panel on the caisson.
D C
1
1
CD 1
2
B
A
Detach from clips the door panel in poi nts
(2) .
R EMOU NT I NG
Perform in the reverse order the dismounting
operations taking i nto account t he following
recommendations: - check the integrity of the deflective
panel and of the continuos layer of Romtix
1502 P sealing materi al on the front door
caisson; - for the mounting of the inside opening
mechanism, the opening control rod will be
placed in the position where the assemble d plate
with electric control is blocked;
- after mounting, check the operation of
the inside opening mechanism and its alignment
with the front door panel; - check t he ope ration of t he front door
speaker.
vnx.su

72
72 - 2
LATERAL OPENINGS TRIMSRear door panel
1 C
B
1A 2
C
2
DISMOUNTIN
G
Dismount :
- window regulator cra nk (A) for glass
lifting that is mounted by clips attachment on
the window regulator axle.
- attachment screw of the inside opening
mechanism (B), consequently, the mechanism;
- locking handle (C) attached by screw;
- attachment screws (1) of the rear door
panel on the caisson; Detach from clips the rear door panel from
points (2).
REMOU NT I NG
Perform the dismounting operations in the
reverse orde r, taking into considera tion the
followings recommendations: - check the integrity of the deflectiv e panel
and of the continuos sealant material layer
Romt ix 1502 P on the door caisson outliner;
- for the mounting of the inside opening
mechanism, the opening control rod will be
placed in the position where the assemble d plate
with electric control is unblocked. - after mounting, check the operation of
the inside opening mechanism and its alignment
w ith the rear door panel.
vnx.su

INSIDE AND REAR LIGHTING
81
81 - 4
The ceiling lamp is central located, between
the two sun visors.
The ceiling lamp has 3 operating positions
subject to ceiling lamp glass position (4):
- position 1 : ceiling lamp off
- position 2 delayed ceiling lighting; this
will light for 15 seconds after driver’s front door
closing or after the command of unlocking the
doors with the RF remote control . This delay
turns out in the moment of setting the contact.
- position 3 : c eiling lamp pe rmanently
lighting.
DISMOUNTIN G
Disconnect the battery ( -) terminal.
Detach from clips the assemb ly from the lamp
support by means of a little screwdriver acting in
front of the slot (A). Disconnect the connector
Remove the roof lining around ceiling lamp
support. Detach from clips the ceiling lamp support.
REMOU NT I NG
Perform the dismounting operations in t he
reverse order. Check the ceiling lamp operation. Ceiling lamp connector
Pin Denomination
1 Mass
2+
protected battery – exit fuse F02
3 Ceiling lamp control
REPLACEMENT OF CEILING LAMP BULB
DISMOUNTIN G
Disconnect the battery (-) terminal;
Detach care fully the lamp glass using a
small screwdriver acting in point ( B).
Remove the worn bulb and replace it.
R EMOU NT I NG
Perform the dismounting operations in the
reverse orde r, using for lamp glass clips
attachment, a small screwdriver positioned in
point (B).
Check the ceiling lamp operation.
Ceiling lamp
A
B
3 1
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 1
This type of anti starting system is based on the key recognition, which has a special constructio n.
It may be separated in two elements which can be identified in the following way: the key head
(position A.) made of plastic, which c an be dismounted and the metal insertion (position B),
which is fixed and ensured by clipping in the key head.
In the key head, there is a coded independent electronic circuit, which is functioning without
battery. When setting the contact on, the anti starting bushing, placed around the starting contact,
is enquiring and catching the coded signal emitted by the key head, then sends it to the Electronic
Control Unit (E.C.U.) decoder. This one is attached on the front left pillar, under the lower casing
of the dashboard and has the function of receiving the code sent from the bushing. If the decoder
recognises the key code then it will send a coded signal to the injection computer, which compares
it with the previous memorised code and will authorise or not the engine starting In case of the system with ra dio frequency remote control (RF) of the doors blocking /
unlocking, the key head has a different construction, having an activation button of the remote
control and a red L ED, which i s lighted i n the moment of bl ocking/unlocking the doors, by
pushing the key button. Inside t he ke y head there i s the coded electroni c c ircuit for the anti
starting system and a printed electronic circuit, supplied by a battery, for the RF remote control
operation of blocking/unlocking the vehicle doors.
The anti starting system is activated after approximate 10 seconds from the breaking of the
contact and is visualised by the blinking of the anti starting indicator placed on the instrument
panel.
AT T E N T I O N !
If the battery is low charged, the tension drop on the starter, at starting, may cause
the activation of the anti starting system and the engine starting is impossible.
General
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 3
The E.C.U. decoder has the following functions :
- deco ding the signal received from the anti starting
bushing; - send ing a code to the injection computer in order to
author ise the engine starting;
- c ontrolling the anti starting indic ator of the instrument
panel;
receiv ing the coded signal from the anti starting bearings,
for the vehicles equipped with RF remote control;
REMA RK :
In case both keys were lost, the code of the key head (8 characters) and the code of the
me tal insertion (4 characters) can be red from the vehicle-purchasing invoice. If also the
invoice was lost, the two mentioned codes can be found out based on the chassis s eries of that
vehicl e, acces sing the database of the DA C IA manufacture r, callin g the “C lient Voice”
department (phone 0248 500 000).
E.C.U. DECODER
General
- commandi ng the blocking/unlocking of the doors, if the vehicle is provided with RF remote
c ontrol keys;
- co mma nding the ceiling delayed light, for vehicles equipped with this system.
Th
e an ti starting bushing is located around the starting contact and is accessible after the
d ismounting the steering wheel’s half-cases. It catches the signal from the key head and then sends
a coded signal to the E.C.U. decoder.
The ve hicles equipped with RF remote control keys for blocking/ unlocking the doors are provided
with another anti starting bushing which transmits to the E.C.U. decoder also the signal received
from the RF remo te control.
Th e recognition of the two types of decoding bushings is performed by means of codes labelled
on their body, as follows : - code 04 2264J - for vehicles without RF remote control;
- code 8200 044257 - for vehicles with RF remote control. ANTI S TARTING BUSHING
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 4
REMARK :
The vehic les equipped with this anti starti ng system, have a type of decoder, and those
provided also with R F remote control for l ocking/ unlocking doors have another ty pe of
decoder.
Th e identification of the two types of E.C.U. decoder is realised by the inscriptions on the
labels as follows: - code P8200032783H and the in scri ption TRANS-PLAF for the vehicle s w ithout RF
remote control; - code P8200032776H and the inscr iption TRF-TRANS-CAR for the vehicles with RF
remote control. ANTI STARTING INDI CATOR
It is located on the instrument panel (position A) and has the following functions:
- signalising the activation of the anti starting system;
- signalising the case of non identifying the key head;
- signalling the entrance in the operation mode “resynchronisation” of the remote controls, RF
with E.C.U. decoder, for the vehicles which use the RF remote control.
When the contact is off and the anti starting system is activated, without any existing failure, the
an ti starting indicator must blink slowly (a blink per second).
After setting the contact on, the anti starting indicator must light for 3 seconds and then turn off.
If a fter setting the contact on, the anti starting system doesn’t work properly, then the anti
starting indicator will blink rapidly (two blinks per second). Th
e ceiling delayed lighting is activated subject to the position of the light glass ( 1):
- position A the ceiling is lighting permanently;
- position B de layed ceiling lighting; this will light for 15 seconds after driver’s front door closing
or after the command of unlocking the doors with the RF remote control. This delay turns out in the
mo ment of setting the contact;
- po sition C ceiling light off.
General
AA
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 5
After ordering a new key head based on the alphanumeric code mentioned on the invoice,
dismount the old key head and remove the metal insertion (mechanical part), then introduce the old
meta l insertion in the new key head according to the previously mentioned procedure. In case the
key head is provided with RF remote control for blocking/ unlocking the doors, after its replacement,
pe rfor m the synchronising procedure of the RF remote control with the decoder, subject to the
fo llowing cases:
- a fter the replacement of the RF key, perform the “Specific synchronised procedure” in order
to bring into phase the RF remote control with the decoder. - if both keys are replaced, perform the “Simple synchronised procedure” for the first RF key
and the “Specific synchronised procedure” for the second one RF key.
If a key was lost, a new key head and a metal insertion are to be ordered.
One key head replacement
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 6
All new decoders, are not coded. After mounting on the vehicle, it is necessary the memorisation
of the key head code by the decoder in order to be operational. If only the decoder is replaced, no
intervention is necessary to the injection computer, which will keep the old anti starting code. When
the vehicle is provided with RF remote control for blocking/unlocking the doors, the performing of
the resynchronisation of the keys with the decoder is imposed, after its mounting. If further to the
di ag nostic of the anti starting system, using the CLIP tester, the replacement of the decoder is
imposed, proceed as follows:
DISMOUNTIN G
- disconnect the (-) terminal of the battery;
- d ismount the ECU decoder-relays assembly;
- ro tate the ECU decoder assembly, in order to have access at its rear connectors;
- d isconnect the front wiring connector from the E.C.U. decoder;
- deta ch ECU decoder from clips of the relays-ECU decoder support.
REMOU NT I NG
- attach in clips the new E.C.U. decoder in the support, connect the front wiring connector to
the ECU decoder, then attach the assembly on the driving post cross member in its place and
mo unt its attachment screw;
- remo unt carefully the access flap of the fuse box;
- reconnect the (-) term inal of the battery.
Proceed then to the insertion of the anti starting code using the contact key, then to its me morising
(va lidation) in the E.C.U. decoder, using the CLIP tester. For this purpose, perform the “E.C.U.
decoder replacement procedure and anti starting code memorising”. Check then the correct operation
of the anti starting system with both keys.
ATTENTION!
Once the decoder has memorised the key codes, this code cannot be erased or replaced
with another one.
If it is necessary the replacement of the kit (E.C.U. decoder and two key heads), then the “ Kit
replacement procedure” must be performed.
Dismounting - remounting E.C.U. decoder
vnx.su