2004 DACIA SOLENZA check engine

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 25
Lubricate the camshaft with engine oil.
Mount the camshaft and its clamp.
Check the camshaft axial clearance, which
must be between 0.06 mm and 0.15 mm , in
case this one i s not corresponding, check the
clamp and the camshaft.
Dismounting – Remounting
Mount : -camshaft sealing gasket by means of
the MOT 1127 – 01 device. - thermostat support;
Loctite 518 is to
be used for its sealing. The l ayer H must be 0.6 till 1 mm thick
and is to be applied as per the following dia-
gram.
-camsha ft gear.
Camshaft gear is to be blocked by means
of the MOT 799 – 01 device and tighten its
a ttachment screw, to the required moment of
4.5 daNm (lubricate the screw head and
thread with engine oil).
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 28
CYLINDERS BLOCK REMOUNTING
Clean the cylinders block, especially t he
jackets s eating and sealing surfaces.
Preparation of assembly
“ pistons-jackets”
The parts contained in the kit are in pairs.
Ma rk the part s assembly from A to D in
order to keep the matching.
Dismounting – Remounting
Remove completely the anti-rust foil.
REMARK:
Never scrape the parts. Jackets over-height
These engines are equipped with rubber
rings for jackets sealing, ensuring only the seal-
ing, jackets being seated directly on the cylin-
ders block and over-height being done from
manufacturing. The checking of the jackets over-height is
to be performed as follows: - place the jackets in the cylinders block
without the sealing ring;
- check t he X over-he ight by means of
the devices MOT 251-01 and MOT 252-01.
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 29
Dismounting – Remounting
The over-he ight X must be between 0.02
mm and 0.09 mm.
Place the jackets in such way that :
-the difference between two joint jackets
to be maximum 0.05 mm;
- the over-height to be in ascending order
between cylinders 1 and 4;
- in case of an incorrect over-height, check
the over-height by m eans of a new kit of jack-
ets, i n order to see i f t he c ause i s the block or
the cylinders jacket or check the theoretical size
values of the block and of the jackets. When over-height is correctly obtained, per-
form the A, B, C, D assembly then mark with
numbers jackets, pistons and the bol ts from 1
to 4 (no.1 towards flywheel) so that the corre-
s pondence with the corresponding connecting
rods may be achieved.
Pistons bolts mounting
The pistons bolts are fixed in connecting rods
and free in pistons. Mount the pistons bolts by means of the
MOT 574-22 that is containing:
- a support for piston ( S);
- an extracting mandrel ( M);
- the piston supporting bushings (B);
- the bolts for mounting ( A) provided with
their centering guides (C ). Use an electric plate of
1500 W (electric
oven) for connecting rods heating. Place the connecting rods on the electric
plate so that connecting rod end surfaces are
in contact with the heating plate.
Check if the pistons bolts are freely gliding
in the new corresponding pistons. Mount the piston bolt E on the mounting
bolt A.
Sc rew the centering guide C till end and
then unscrew it for a quarter of turn.
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 30
The arrow marked on the piston head must
be oriented towards engine flywheel. The c onnecting rods ha ve no mounting
direction, but the ha lf-bearings spurs are to
be positioned on the same part. In order to assemble the piston and the
connecting rod, proceed as follows: -place the bushing B 13 on the support
and attach the piston (with the arrow oriented
upwards) on the bushing;
Dismounting – Remounting
- lubricate the centering guide and the
piston bolt with engine oil;
- check t he free gliding of the piston
bolt and the piston positioning.
When the connecting rod end is reaching
the necessary temperature (about 250 °C),
proceed to the ra pid of the piston bolt, as
follows: -introduce the centering guide in the
piston; - position the connecting rod i n the
piston;
-press till end the piston bold.
Check if the pi ston bolt is remaining re -
tired as against the piston outer diameter for
each of the connecting rod position in the pis-
ton.
Rings mounting
Mount the rings on the pi ston in the
following sequence: -
oiling ring ( 3);
-s ealing ri ng (2) w ith the mark “TOP”
upwards; -compression ri ng (1) with t he mark
“TOP” upward. The compression and sealing rings are to be
mounted with the slots disposed at 90° against
de bolt’s axle and displaced between them with
180°. The oiling ring is to be mounted with the
slot oriented at 45° against the bolt’s a xle.
The rings slots being adjusted, shall never be
reworked.
Lubricate the pistons with engine oil.
M ount the assemblies “connecting rod-
piston-rings” in the cylinder’s jackets, by means
of the mounting bushing. Mount the sealing gaskets on the cylinder
jackets.
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 31
Mount the assembly i n the bl ock, as per
previous established sequence and check and
ensure that a 0.1 mm gauge is passing be-
tween jackets.
Dismounting – Remounting
MOT 484
Block the jackets by means of the device
MOT 484 or the clamps MOT 588.
M ount the base bearing on the cylinders
block. Hal-bearing lining that are mounted on
casing are provided with oiling holes.
The beari ngs lining are matching with the
crankshaft in two classes, as follows: Mount connecting rod bearings (connecting
rod bearings are the same) Lubricate the cranckpin and the bearings.
Mount the crankshaft and the axial bearings.
Mount the bearings caps. On the no.1 cap
(area K) apply a layer of LOCTITE 518, be-
tween 0.6 and 1 mm thick.
Tighten the bearings caps to a required mo-
ment of 2.5 daNm then to an a ngle of 43° ± 6°.
Check the axial clearance of the crankshaft,
which must be between:
*0.045 and 0.852 with wear;
* 0.045 and 0.252 without wear.
Marking on bearing
Red
Bl ue
Marking on crankshaft
A
B
Ide nt i dfi cation of m atching c lasses on
crankshaft i s performed by m arking on t he
balance-weight of bearing number 5. Marking example on crankshaft:
A AB AB
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 32
The axial bearings may have the following
thickness: 2.80, 2.85, 2.90, 295 mm.
M ount the connecting rods caps and
tighten to the required moment of 4.2 daNm.
Check:
-connecting rods lateral clearance;
- assembly rotation.
Mount: -gear and driving chain of the oil pump;
- oil pump (check the existence of the
centering bushings) and tighten the screws to
the required moment of 2.5 daNm;
Dismounting – Remounting
MOT 550
- the crankshaft closing casing; the
sealing is performed using LOCTITE 518 (
the layer H must be 0.6 – 1 mm thick);
- sealing gasket from crankshaft clos-
ing casing (lubricated with oil) by means of
the MOT 550 device;
-crankshaft sealing gasket towards fly-
wheel (at no. 1 bearing) by means of the MOT
1129-01 device. Lubricate the sealing gasket external part
and lip with engine oil.
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 41
DISMOUNTIN G
Drain the oil from the engine.
Dismount :
- lower casing (see chapter 10”Lower casing on vehicle”).
Dismount the oil pump attachmen t screws on casing.
Dismount the drive chain from the oil pump gear.
Dismount the oil pump cap.
Check the gears clearance in the oil pump (see chapter 10” Engine assembly”)
REMOU NT I NG
Perform the dismounting operations in the reverse order;
Fill up engine with oil
Check the oil pressure at 80 °C:
At idling 1 bar;
At 4000 rot/min 3 bar. Oil pump attachment screws 2.5
Oil pump cap attachment screws 1

TIGHTENING MOMENTS (daNm)
O
il pump
vnx.su

ENGINE E7J-26211
11 - 5
DISTRIBUTION SYSTEM
MOT 484
Cylinder head gasket
Mount the MOT 484 device or MOT
588 clamps for jackets maintenance.
Check the cylinder head smoothness using
a lineal a nd a set of templates. The maximal admissible deformation: 0.05
mm. The cylinder head is not to be rectified!REMOU NT I NG
Clean the gasket-seating surface of the cyl-
inder head.
Mount the cylinder head with a new gasket.
Perform the dismounting operation s in the re-
verse order.
Tighten the cylinder head observing the cyl-
inder head tightening method described in chap-
ter 10 “Dismounting-Remounting” .
Mount the distribution belt ( see chapter 11
”Distribution belt”).
Adjust the tilters.
Perform the cooling circuit filling and purging
(see chapter 19 “ Filling and Purging” ).
REMARK:
At each operation implying battery dis-
mounting,
when reconnecting it, introduce the radio
code t hat is written on the vehicle-purchas-
ing invoice.
vnx.su