2004 DACIA SOLENZA air conditioning

16ENGINE E7J-262
16 - 5
ALTERNATOR – STARTER
21
Vehicles equipped with air conditioning
DISMOUNTIN G
Place the vehicle on a two-column elevator
Disconnect the battery
Dismount the alternator upper attachment screw.
Dismount the front right wheel.
Lift the vehicle.
Dismo unt :
- protection fairing;
- lateral tie-rod ( 1);
-s hock absorber two attachment screws (2) on steering knuckle.
Swing over the steering knuckle and remove the right planetary transmission from the plan-
etary gear of the gearbox. Disconnect the electric connectors of the alternator.
Dismount the alternator lower attachment screw.
Dismount the alternator’s belt.
Remove the alternator, laterally by the right planetary transmission.
REMARK:
In order to replace the alternator belt, first dismount the accessories driving belt
(compressor and/or power steering pump).
R EMOU NT I NG
Perform the dismounting operations in the reverse order.
Tighten the alternator driving belt to 263 HZ ± 10% by means of the MOT 1505 device (see
the m ethod described in c hapter 07 “ Accessories belts tightening”)
Tighten to the required moment the alternator’s attachment screws.
REMARK:
A dismounted belt is not to be remounted, but replaced.
Alternator
vnx.su

IGNITION AND INJECTION
17
17 - 4
Injection system
CHARACTERISTICS
• Electronic control unit (UCE injection) with 90 pins SIEMENS.
• Sequential multi-poin t injection.
• Controlling one injector each time.
• Static ignition with a double ignition coil.
• Canister purging valve controlled in opening duty cycle.
• Idling regime correction subject to:
- climate maintenance (air conditioning);
- battery voltage.
• Maxima l regime:
- 6200 rot/min for first, second and third speed;
- 6000 rot/min for fourth and fifth speed.
vnx.su

IGNITION AND INJECTION
17
17 - 5
ELEMENTS LOCATION
1. RPM sensor ( tightening moment : 0.8 daNm);
2. Water temperature sensor (tightening moment: 2.5 daNm);
3. Atmospheric pressure sensor;
4. Step-by-step engine for idling adjustment;
6. Air temperature sensor;
7. UCE injection;
8. Choke sensor;
9. Fuse and relays box;
10. Air filter;
11 .D etonation sensor (tightening moment: 2.5 daNm);
12. Oxygen sensor (tightening moment: 4.5 daNm);
13. Ignition coil;
14. Carbon canister with purging valve included;
15. Power steering pressure controller(tightening moment: 1.2 daNm);
16. Air conditioning pressure controller (tightening moment: 0.8 daNm).
Injection system
13 10 11 5 4 6 3 2 1 8 9
14 1 6 15 12 7
vnx.su

IGNITION AND INJECTION
17
17 - 10
MU LTI-POINT INJE CT ION CHARACT E RISTICS
〈 SIRIUS 32 with 90 pins computer is managing the ignition and the injection.
〈 For diagnostic, CLIP Sagem tester is to be used.
〈 The injection system in use is a sequential multi-point type, injection and ignition phases
controlling being based on the SIRIUS 32 computer program logic, starting from the signal received
from the RPM sensor.
〈The pr esence of the anti-pollution indicator OBD on the instrument panel, that is lighted for
3 seconds when setting the contact on, is specific to the vehicles observing pollution norms EURO
2000. The injection computer of these vehicles is provided with diagnostic system type OBD (“ On
Board Diagnostic).
〈 Idling regime correction is subject to:
-c limate maintenance on/off control (air conditioning)
-e lectrical balance on vehicle, as a result of connecting different electric consumers.
〈 EURO 2000 specific vehicles are provided with two oxygen sensors located in front of the
cata lyst (upstream oxygen sensor) and after catalyst (downstream oxygen sensor).
〈 At EURO 2000 specific vehicles, the fuel supply is performed at constant pressure (3.5 ±
0.2 bar), the pressure controller placed in the fuel tank being provided for this purpose.
Chara cteristics
vnx.su

IGNITION AND INJECTION
17
17 - 11
AIR CONDITIONING UNIT IS USING A COMPRESSOR
WITH VARIAB LE DI SPLACE M ENT
Th e connections injection/air conditioning, are the followings:
- pin 46 of the injection computer is receiving the information “ air conditioning
re que st” further to the air conditioning switch acting;
- pin 10 of the injection computer will transmit the coupling control of the air
co nditioning compressor by means of the “A” relay, if the coupling authorization conditions are
accomplished.
The information “power absorbed by compressor” displayed when performing diagnostic by
means of the CLIP tester, is related to the couple value taken by the compressor. This is of 300-
5000W, the minimal displayed value being of 300 W, regardless the compressor coupled / unc oupled
c ondition.
Th e injection computer is forbidding the compressor coupling in the following situations:
-at less than 16 seconds from engine starting;
-subject to the power requested to the engine by the vehicle driver.
-when th e acceleration pedal is fully pressed;
-i f the engine RPM is lowering till 550 rot/min (compressor is again coupling if the RPM is
r eachi ng to 1800 rot/min);
-if the wa ter temperature has increased to over 110° C;
-if the engi ne RPM is exceeding 6000 rot/min.
Injection / air conditioning strategy
vnx.su

IGNITION AND INJECTION
17
17 - 69
Diagnostic – States interpretation
ET009CLIMATE CONTROL REQUEST
RECOMMEND AT IONS No failure must be prese nt or memorized.
The injection computer is not noticing the air conditioning starting control.
Ch eck the in sulation and continuity on the line from pin 23 (climate contr ol of type Info Power
Absorbed by compressor) or from pin 46 (climate control of type Logical connection) of the injection
computer.
M end if necessary.
If the proble m is persisting consult the climate control diagnostic.
AF TER Restart the conformity checking from the beginning.
REPARATION
vnx.su

19
19 - 4
COOLING - EXHAUST - TANKCooling system diagram
ThermostatWa t e rpump
Composition :
1. Engine
2. Cooling radiator
3. Expansion vessel
4. Heating radiator
5. Thermostat support
6. Nozzle Ø 3
7. Purging screw
T. T h ermostat
The operation of the engine fan is controlled by the UCE injection, as follows:
1. For vehicles without air conditioning –cooling engine fan cooling is starting when water temperature is over 99°C;
– cooling engine fan cooling is stopping when water temperature is lower than 96°C.
2. For the vehicles with air conditioning. -cooling engine fan cooling is starting on first step when water temperature is over 99°C;
- cooling e ngine fan c ooling is start ing on second step when water temperature is over
104°C; - cooling engine fa n cooling is switching from second step to first step, when water
temperature is lower than 101°C; -engine fan cooling is stopping when water temperature is lower than 96°C.
vnx.su

19
19 - 5
COOLING - EXHAUST - TANK
Radiator
SPECIAL TOOLS
MOT 1202 - 01
Pliers for elastic clips
MOT 453Hoses clamp
DISMOUNTIN G
Drain the air conditioning unit – for the ve-
hicles with air conditioning (see chapter 62” Fill-
ing –Draining the air conditioning circuit”). Disconnect the battery
Dismount the air inlet duct from the battery
screen. Detach from clips the oi l reservoir from the
battery screen, for the ve hicles equipped with
power steering. Clamp the hoses from radiator by means of
MOT 453 device.
Dismount the hoses from radiator by means
of the pliers for elastic clips MOT 1202-01 and
recover the cooling fluid.
Disconnect the engine fan connector (1).
Detach the wiring from clips ( 2) and (3).
Di sconnect the resistance connector ( 4), for
the vehicles with air conditioning. Carefully release the engine fan from the four
attachment clips ( 5) on the radiator- for the
ve hi c l e s e qui ppe d wi t h a i r c ondi t i oni ng,
c onsequently, the four screws ( 6) are
di sm ount e d, f or t he ve hi c l e s without a i r
conditioning.
The vehicles without air conditioning. Carefully remove the engine fan from the
sustaining p oints (7).
Dism oun t t he ra di a t or of f t he si de
attachment supports on the radiator upper
cross beam. Disconnect the two pipes from condenser.
Re l ease t he ra di ator from the lowe r
su p po r tin g buffers togeth er with the
condenser and recover the cooling fluid from
the radiator. Dismount t he condense r a ttachm ent
sc rews on the cooling radiator (for vehicles
with air conditioning).
For vehicles with air conditioning.
REMOU NT I NG
Mount the condenser on the new cooling
radiator (for vehicles with air conditioning).
M ount the radiator-condenser assembly
on the vehicle, by supporting it in the lower
elastic supports and attach it in the supports
of the radiator upper cross beam. Mount the engine fan assembly on the
sustaining supports (7) and attach it in the four
screws (for vehicles without air conditioning).
54
3
1
5
2
vnx.su