2004 DACIA SOLENZA engine

ENGINE E7J-26216
16 - 4
ALTERNATOR – STARTER
SPECIAL TOOLS
MOT 1505 Belt tension measurement device
TIGHTENING MOMENTS (daNm)
Upper attachment screw 2,2
Lower attachment screw 5
MOT 1505
Ve
hicles without air conditioning.
DISMOUNTIN G
Place the vehicle on a two-column elevator.
Disconnect the battery.
Disconnect the fuel supply pipe.
Dismo unt :
- air filter;
- oil gauge pipe;
- alternator upper attachment screw;
- alternator’s belt;
- alternator tightening clamp.
Lift the vehicle.
Disconnec t the alternator electric connectors.
Di smount the alternator l ower attachment
screw.
Lower the vehicle.
Remove the alternator through the upper part.
REMOU NT I NG
Perform the dismounting operations in the
reverse order Tighten the alternator driving belt to 263
HZ ± 10% by means of the MOT 1505
device (see the method described in chapter
07 “ Accessories belts tightening”)
Tight e n to t he re qui red m om ent the
alternator’s attachment screws.
Alternator
vnx.su

16ENGINE E7J-262
16 - 5
ALTERNATOR – STARTER
21
Vehicles equipped with air conditioning
DISMOUNTIN G
Place the vehicle on a two-column elevator
Disconnect the battery
Dismount the alternator upper attachment screw.
Dismount the front right wheel.
Lift the vehicle.
Dismo unt :
- protection fairing;
- lateral tie-rod ( 1);
-s hock absorber two attachment screws (2) on steering knuckle.
Swing over the steering knuckle and remove the right planetary transmission from the plan-
etary gear of the gearbox. Disconnect the electric connectors of the alternator.
Dismount the alternator lower attachment screw.
Dismount the alternator’s belt.
Remove the alternator, laterally by the right planetary transmission.
REMARK:
In order to replace the alternator belt, first dismount the accessories driving belt
(compressor and/or power steering pump).
R EMOU NT I NG
Perform the dismounting operations in the reverse order.
Tighten the alternator driving belt to 263 HZ ± 10% by means of the MOT 1505 device (see
the m ethod described in c hapter 07 “ Accessories belts tightening”)
Tighten to the required moment the alternator’s attachment screws.
REMARK:
A dismounted belt is not to be remounted, but replaced.
Alternator
vnx.su

ENGINE E7J-26216
16 - 6
ALTERNATOR – STARTER
ENGINE STARTER
E7 J - 262 D 907 - M00 2T 13581
IDENTIFICATION
DIAGNOSTIC
Special tool : CLIP tester – TECHNIC for measuring the battery voltage and the absorbed
intensity in the starting stage.
OPERATION ABNORMALITIES THAT MIGHT BE NOTICED
- Battery failure = large voltage drop on starter during engine starting stage.
- Blocked starter = the absorbed current is very high.
- Solenoid failure = the absorbed current is very low.
In order to perform the measurements, it is necessary the engine drive by means of the starter,
but stopping the engine starting.
To do that, disconnect the RPM sensor (located on clutch casing).
REMARK:
After performing this checking, erase by means of the CLIP tester, the possible failures
memorized by the computer.
St arter
vnx.su

16ENGINE E7J-262
16 - 7
ALTERNATOR – STARTER
TIGHTENI NG MOMENTS (daNm)
Starter attachment screws 4.4
Control bar attachment screw
on ge arbox connecting rod 2.7
DISMOUNTIN G
Place t he vehicle on a two-column elevator.
Disconnect the battery.
Dismount the attachment nuts of the gazes exhaust vessel.
Dismount the hoses support attachment nut on the engine lifting support.
Dismount the control bar attachment screw on the gearbox connecting control rod (recover
the bushing). Dismount the starter attachment screws (1).
Suspend the vehicle.
Disconnect the starter electric connectors.
Remove the starter through the lower part of the engine compartment.
R EMOU NT I NG
Perform the dismounting operations in the reverse order.
Tighten the screws and nuts to the required moment.
Fill the protection bellows of the gearbox connecting rod joint, with grease Molycote 33M –
10 ml.
St arter
vnx.su

IGNITION AND INJECTION
17
17 - 1
PRESENTATION
The system is composed of : -electronic control unit (UCE injection);
-a double ignition coil;
-f our spark plugs;
- spark plugs cables.
OPERATING PRINCIPLE
Subject to the information received from different sensors, but mainly subject to engine RPM
and charge, the electronic control unit will establish the advance at ignition, will identify the cylinders
being at upper dead point and consequently , will control the corresponding coil to them.
This is producing the spark at the level of the two cylinders being at upper de ad point,
interrupting the mass connection of the corresponding coil.
Ignition system
vnx.su

IGNITION AND INJECTION
17
17 - 5
ELEMENTS LOCATION
1. RPM sensor ( tightening moment : 0.8 daNm);
2. Water temperature sensor (tightening moment: 2.5 daNm);
3. Atmospheric pressure sensor;
4. Step-by-step engine for idling adjustment;
6. Air temperature sensor;
7. UCE injection;
8. Choke sensor;
9. Fuse and relays box;
10. Air filter;
11 .D etonation sensor (tightening moment: 2.5 daNm);
12. Oxygen sensor (tightening moment: 4.5 daNm);
13. Ignition coil;
14. Carbon canister with purging valve included;
15. Power steering pressure controller(tightening moment: 1.2 daNm);
16. Air conditioning pressure controller (tightening moment: 0.8 daNm).
Injection system
13 10 11 5 4 6 3 2 1 8 9
14 1 6 15 12 7
vnx.su

IGNITION AND INJECTION
17
17 - 7
Injection system
In the fuse box located in the engine compartment, the following relays may be identified:
A. Co mpressor relay
B. Engine c ooling fan relay, step I
C. Engine cooling fan relay, step II
D. UCE injection relay, canister-purging valve
E. Fog projectors relay
H. Fuel pump and ignition coil relay
14. C arbon canister with purging valve
included
;
16.
Power steering pressure controller; 12.
Oxygen sensor;
15.
A ir conditioning pressure controller.
1
15
12
1614
vnx.su

IGNITION AND INJECTION
17
17 - 8
Injection system
WATER TEMPERATURE SENSOR
The water temperature sensor ( 1) is sending to UCE injection the information regarding water tempera-
tu re, and another information is sent to the indicator from the instrument panel, which will show the water
tem perature.
In case of an alert regarding the water temperature, UCE injection will control the lightening of
the water temperature indicator from the instrument panel.
Subject to water temperature, UCE injection will control:
- injection system;
- relays for controlling the engine cooling fan.
When setting the contact on, the water temperature indicator located on the instrument panel,
will be lighted for 3 seconds, then it will turn off.
1
1
If after the contact is set off, in the next 2 minutes from engine stopping, the water temperature
is reaching 102 °C, and t hen the injection computer i s control ling t he starting of the e ngine
cooling fan at low speed. When the temperature is lowering at 95°C, the engine cooling fan stopping will be controlled;
its operation must not exceed 10 minutes after engine stopping.
vnx.su