2004 Acura RL light

If you f orget and leave the key in the
ignition switch, Lockout Prevention
will not allow you to lock the driver’s
door. With the driver’s door open
andthekeyintheignition,both
master door lock switches are
disabled. However, if the driver’s
door is not open, the master door
lock switches are not disabled.
Pushing the switch down on the
open passenger’s door will lock all
doors. If you try to lock an open
driver’s door by pushing in the lock
tab, the tabs on all doors pop out.
Pushinginthelocktabonthe
passenger’s door only locks that door.The ceiling lights (if the ceiling light
switch is in the center position) and
the door courtesy lights will come on
when you press the UNLOCK button.
If you do not open any door, the
lights stay on f or about 10 seconds,
then f ade out. If you relock the doors
with the remote transmitter before
10 seconds have elapsed, the lights
will go of f immediately.
You can lock and unlock your car
with the remote transmitter. When
you push the LOCK button, all doors
lock. You will hear a beep, and the
parking lights, taillights and license
plate lights will f lash once. When you push the UNLOCK button
once, only the driver’s door unlocks.
The remaining doors unlock when
you push the button a second time.
You will hear two beeps, and the
outside lights will f lash twice, each
time you push the button.
Remote Transmitter
L ockout Prevent ion
Keys and Locks
Inst rument s and Cont rols84
LOCK
BUTTON
LED
UNLOCK
BUTTON TRUNK
RELEASE
BUTTON
PANIC
BUTTON

If you unlock the doors with the
remote transmitter, but do not open
any of the doors within 30 seconds,
the doors automatically relock and
the security system sets.
You cannot lock any of the doors
with the remote transmitter if any
door is not f ully closed or the key is
in the ignition switch. You cannot
unlock any of the doors with the key
in the ignition switch.
To open the trunk, push the Trunk
Release button f or approximately
one second.
You can open the trunk with the
remote transmitter regardless of the
position of the main switch in the
glove box. The trunk will not open if
the key is in the ignition switch.You can program the keyless entry
system so it does not beep when you
lock and unlock the doors. This
procedure only turns of f the beep;
the exterior lights will still f lash.
Panic mode allows you to remotely
activate your car’s security system to
attract attention. When activated, the
horn will sound, and the exterior
lights will f lash, f or about 30 seconds.
To activate panic mode, press and
hold the PANIC button for about two
seconds.
To cancel Panic mode bef ore 30
seconds, press any button on the
remote transmitter. You can also
turn the ignition switch to ON (II).
Panic mode will not activate if the
ignition switch is in the ON (II)
position.
To turn this feature off, stand near
the vehicle with the remote
transmitter. Press and hold the
Trunk Release button, then press the
Lock button within one second. You
should see the LED on the remote
transmitter come on f or one second.
Release the buttons after the LED
goes out.
To turn this feature on, repeat the
above procedure. You should see the
LED blink twice.
Af ter you program the remote
transmitter, make sure the trunk lid
is closed.
CONT INUED
T urning t he Beep Of f and On
Panic Mode
Keys and Locks
Inst rument s and Cont rols85

The glove box light comes on only
when the parking lights are on. Open the glove box by pulling the
bottom of the handle. Close it with a
f irm push. Lock or unlock the glove
box with the master key. Glove Box
Keys and Locks
Inst rument s and Cont rols90
An open glove box can cause
serious injury to your passenger
inacrash,evenifthe
passenger is wearing the seat
belt.
Always keep the glove box
closed while driving.

Adjust the outside mirrors with the
adjustment button on the driver’s
door armrest:Turn the ignition switch ON (II).
Move the selector switch to L
(driver’s side) or R (passenger’s
side).
Keeptheinsideandoutsidemirrors
clean and adjusted f or best visibility.
Be sure to adjust the mirrors bef ore
you start driving.
The inside mirror can automatically
darken to reduce glare. To turn on
this feature, press the button on the
bottom of the mirror. The AUTO
indicator comes on as a reminder.
When it is on, the mirror darkens
when it senses the headlights of a
vehicle behind you, then returns to
normal visibility when the lights are
gone. Press the button again to turn
of f this sensor.1.
2. Adjusting the Power Mirrors
Mirrors
Inst rument s and Cont rols96
SELECTOR SWITCH
SENSOR
INDICATOR
AUTO BUTTON

The outside mirrors are heated to re-
move fog and frost. With the ignition
switchON(II),turnontheheaters
by pressing the button. The light in
the button comes on as a reminder.
Press the button again to turn the
heaters of f .
When you f inish, move the
selector switch to the center (off)
position. This turns of f the
adjustment button so you can’t
move a mirror out of position by
accidentally bumping the button.
Move the mirror right, left, up or
down by pushing the adjustment
button in that direction. Outside mirror positions can be
stored in the driving position
memory system (see page ). 4.
3. 98
Mirrors
Inst rument s and Cont rols97
ADJUSTMENT BUTTON HEATED MIRROR BUTTON

Press and release the MEMO
buttononthecontrolpanel.You
will hear a beep. Immediately
press and hold one of the memory
buttons (1 or 2) until you hear two
beeps. The indicator light in the
memory button will come on. The
current positions of the driver’s
seat, steering wheel, and outside
mirrors are now stored.
Your Acura has a memory f eature
f or the steering wheel, driver’s seat,
and outside mirror positions.
Turn the ignition switch ON (II).
You cannot add a new driving
position in the memory unless the
ignition switch is ON (II). You can
recall a memorized position with
the ignition switch in any position.
Two seat, steering wheel, and
outside mirror positions f or dif f erent
drivers or driving conditions can be
stored in separate memories. You
select a memorized position by
pushing the appropriate button.
Adjust the seat to a comfortable
position (see page ). Adjust
the steering wheel to a
comf ortable position (see page). Adjust the outside mirrors
f or best visibility (see page ).
Store a driving position as explained
in this section only when the vehicle
is parked.
3.
1.
2.
76 96
91
St oring a Driving Posit ion in Memory
Driving Posit ion Memory Syst em
Inst rument s and Cont rols98
MEMO BUTTON

Doing any of the f ollowing af ter
pressing the MEMO button will
cancel the storing procedure.Not pressing a memory button
within 5 seconds.
Readjusting the seat or steering
position.
You can select memorized positions
as f ollows.Make sure the parking brake is set
and the shif t lever is in Park.
Insert the key in the ignition
switch. If you do not insert the key
in the ignition switch, the steering
wheel will not adjust to the
memorized position until you do. Press the desired memory button
(1 or 2) until you hear a beep, then
release the button.
The system will move the seat,
steering wheel and outside mirrors
to the memorized positions. The
indicator light in the selected
memory button will f lash during
movement. When the adjustments
are complete, you will hear two
beeps and the indicator light will
remain on.
Readjusting the outside mirror
position.
Each memory button stores only one
driving position. Storing a new
position erases the previous setting
stored in that button’s memory. If
you want to add a new position while
retaining the current one, use the
other memory button.
All stored driving positions will be
lost if your car’s battery goes dead or
is disconnected. 3.
1.
2.
CONT INUED
Select ing a Memorized Posit ion
Inst rument s and Cont rols
Driving Posit ion Memory Syst em
99
MEMORY BUTTONS

Press any button on the control
panel: MEMO, 1 or 2.
Push any of the adjustment
switches f or the seat or steering
wheel.
Shif t out of Park.
To stop the system’s automatic ad-
justment;
Adjust the outside mirrors.
If you select a memorized position
without inserting the key in the
ignition switch, only the seat and
outside mirrors will adjust. To get
the system to also adjust the steering
wheel, insert the key in the ignition
switch. You will hear two beeps
when it is complete. Both f ront seats are equipped with
seat heaters. The ignition switch
must be ON (II) to use them. Push
the front of the switch, HI, to rapidly
heat up the seat. After the seat
reaches a comf ortable temperature,
select LO by pushing the back of the
switch. This will keep the seat warm.
If desired, you can use the adjust-
ment switches to change the posi-
tions of the seat, steering wheel or
outside mirrors af ter they are in
their memorized position. If you
change the memorized position, the
indicator light in the memory button
will go out. To keep this driving
position f or later use, you must store
it in the driving position memory.
Seat Heaters
Driving Position Memory System, Seat Heaters
Inst rument s and Cont rols100
SEAT HEATERS