2004 Acura MDX Owner's Manual

µµ
Always use Honda Power Steering
Fluid. You may use another power
steering f luid as an emergency
replacement, but have the power
steering system f lushed and ref illed
with Honda PSF as soon as possible.
A low power steering f luid level can
indicate a leak in the system. Check
the f luid level f requently, and have
the system inspected as soon as
possible.
The timing belt should be replaced
at the intervals shown in the
maintenance schedule.
Replace the belt at 60,000 miles
(100,000 km) if you regularly drive
your vehicle in one or more of these
conditions:
In very high temperatures
(over 110°F, 43°C).
In very low temperatures
(under 20°F, 29°C).
Frequently tow a trailer.
Check the level on the side of the
reservoir when the engine is cold.
The f luid should be between the
UPPER LEVEL and LOWER LEVEL.
If not add power steering f luid to the
UPPER LEVEL mark.
Power Steering Fluid, Timing Belt
Maint enance
Timing Belt
Power Steering Fluid
213
NOTICE:
UPPER LEVEL
LOWER
LEVEL
T urning the steering wheel to
f ull lef t or right lock and holding it
there can damage the power steering
pump.

Clean the hood latch assembly with a
mild cleaner, then lubricate it with a
multipurpose grease. Lubricate all
the moving parts (as shown),
including the pivot. Follow the time
and distance recommendations in
the Maintenance Schedule. If you
are not sure how to clean and grease
the latch, contact your Acura dealer.Theheadlightswereproperlyaimed
when your vehicle was new. If you
regularly carry heavy items in the
cargo area or pull a trailer,
readjustment may be required.
Adjustment should be done by an
Acura dealer or other qualif ied
mechanic.
Your vehicle has halogen headlight
bulbs, two on each side. When
replacing a bulb, handle it by its base
and protect the glass from contact
with your skin or hard objects. If you
touch the glass, clean it with
denaturedalcoholandacleancloth.
Open the hood.
1.
Hood Latch, Lights
Maint enance
Hood L atch Replacing a Headlight Bulb
Headlight A iming
214
NOTICE:
LATCH ASSEMBLY
Halogen headlight bulbs get
very hot when lit. Oil, perspiration, or a
scratch on the glass can cause the bulb
to overheat and shatter.

Push the electrical connector onto
the new bulb.
Insert the new bulb into the hole
and turn it one-quarter turn clock-
wise to lock it in place.
Turn on the headlights to test the
new bulb.Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
To remove a bulb, pull it straight
out of its socket.
Remove the electrical connector
f rom the bulb by squeezing the
connector to unlock the tab, then
slide the connector of f the bulb.
Remove the bulb by turning it
approximately one-quarter turn
counterclockwise.
1.
2.
4.
5.
6.
2.
3.
CONT INUED
Lights
Maint enance
Replacing Front Turn Signal/
Parking and Side Marker L ight
Bulbs
215
TAB
BULB CONNECTOR

Install the new bulb into the
socket.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Testthelightstomakesurethe
new bulb is working.Open the tailgate. Use a
screwdriver protected with a cloth
to pry open the two covers.
Remove the two screws and
remove the rear light assembly
f rom the rear pillar.
Determine which of the f our bulbs
is burned out: brake/taillight, turn
signal/hazard lights, side marker
light, or back-up light.Remove the socket by turning it
one-quarter turn counterclockwise.
Remove the burned-out bulb by
pulling it straight out of the socket.
1.
2.
3. 4.
5.
3.
4.
5. Replacing Rear Bulbs
Lights
Maint enance216

Install the new bulb into the
socket.
Push the socket into the light
assembly and turn it clockwise
until it locks.
Testthelightstomakesurethe
new bulb is working.
Install the rear light assembly in
the body. Tighten the two screws.
Snap the covers back into position.Remove the light assembly cover
by prying caref ully with a cloth-
covered screwdriver in the
notches along the top edge. Then
pivot the cover out and down.
Remove the socket f rom the light
assembly by turning it one-quarter
turn counterclockwise.Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Testthelightstomakesurethe
new bulb is working.
Put the socket back into the light
assembly and turn it clockwise to
lock it in place.
Place the cover back into the light
assembly. Push it up until it locks
in place.
1. 4.
5.
6.
2. 3.
6.
7.
8.
9.
Lights
Maint enance
Replacing a High-mount Brake
Light Bulb
217

If your seat belts get dirty, use a sof t
brush with a mixture of mild soap
and warm water to clean them. Do
not use bleach, dye, or cleaning
solvents. Let the belts air-dry bef ore
you use the vehicle.
Dirt build-up in the loops of the seat
belt anchors can cause the belts to
retract slowly. Wipe the insides of
the loops with a clean cloth
dampened in mild soap and warm
water or isopropyl alcohol.The driver’s f loor mat that came
with your vehicle hooks over the
f loor mat anchor. This keeps the
f loor mat f rom sliding f orward and
possibly interf ering with the pedals.
If you remove the driver’s f loor mat,
make sure to re-anchor it when you
putitbackinyourvehicle.If you use a non-Acura f loor mat,
make sure it f its properly and that it
canbeusedwiththefloormat
anchor. Do not put additional f loor
mats on top of the anchored mat.
Maint enance
Seat Belts
Floor Mats
Seat Belt s, Floor Mat s
218
LOOP

Check the condition of the wiper
blades at least every six months.
Replace them if you f ind signs of
cracking in the rubber, and areas
that are getting hard, or if they leave
streaks and unwiped areas when
used.To replace a wiper blade:Raise the wiper arm of f the
windshield.
Windshield: Raise the driver’s side
first, then the passenger’s side. Front only:
Disconnect the blade assembly
fromthewiperarmbypushingin
the lock tab. Hold the lock tab in
while you push the blade assembly
toward the base of the arm.
2.
1.
CONT INUED
Wiper Blades
Maint enance219
WIPER ARMS
LOCK TAB

Remove the blade f rom its holder
by grasping the tabbed end of the
blade. Pull f irmly until the tabs
come out of the holder.Examine the new wiper blades. If
they have no plastic or metal
reinf orcement along the back
edge, remove the metal
reinf orcement strips f rom the old
wiper blade, and install them in
the slots along the edge of the new
blade.Slide the new wiper blade into the
holder until the tabs lock.
Front only:
Slide the wiper blade assembly
onto the wiper arm. Make sure it
locks in place.
Windshield: Lower the passenger’s
side first, then the driver’s side. Lower the wiper arm down against
the window.
6.
7.
4. 5.
3.
Wiper Blades
Maint enance220
BLADE BLADE
REINFORCEMENT