2004 Acura MDX Owner's Manual

µµµµµ
µ
CONT INUED
This position mechani-
cally locks the transmission. Use
Park whenever you are turning of f or
starting the engine. To shif t out of
Park, you must press on the brake
pedal and have your f oot of f the
accelerator pedal.
If you have done all of the above and
still cannot move the lever out of
Park, see on
page .
To avoid transmission damage, come
to a complete stop bef ore shif ting
into Park. The shif t lever must be in
Park bef ore you can remove the key
from the ignition switch. Press the brake
pedal to shift from Park to Reverse.
To shif t f rom Reverse to Neutral,
come to a complete stop and then
shif t.
Your vehicle has a reverse lockout so
you cannot accidentally shif t to
Reverse from Neutral or any other
driving position when the vehicle
speed exceeds 7 9 mph (12 14
km/h).
If you cannot shif t to Reverse when
the vehicle is stopped, press the
brake pedal and slowly shift to
Neutral, and then to Reverse.
If there is a problem in the reverse
lockout system, or your vehicle’s
battery is disconnected or goes dead,
you cannot shif t to Reverse. (Ref er
to Shif t Lock Release on page ). Use Neutral if you
need to restart a stalled engine, or if
it is necessary to stop brief ly with
the engine idling. Shif t to the Park
position if you need to leave your
vehicle for any reason. Press on the
brake pedal when you are moving
the shift lever from Neutral to
another gear.
Use this position f or
normal driving. The transmission
automatically selects a suitable gear
f or your speed and acceleration. You
may notice the transmission shif ting
up at higher speeds when the engine
is cold. This helps the engine warm
up f aster.
175
175
Automatic Transmission
Driving
Park (P)Shif t L ock Release Reverse (R)
Neutral (N)
Drive (D )
5
173

µµ µThese positions
are similar to D , except when you
select the D position, only the f irst
f our gears are selected. When you
select D , only the f irst three gears
are selected. D can also keep the
transmission f rom cycling between
f ourth and f if th gears in stop-and-go
driving, and D can keep the
transmission f rom cycling between
third and f ourth gears. This position locks
thetransmissioninsecondgear.It
does not downshif t to f irst gear
when you come to a stop.
Use Second gear: For more power when climbing.
To increase engine braking when
going down steep hills.
For starting out on a slippery
surf ace or in deep snow.
When driving downhill with a
trailer. With the lever in this
position, the transmission locks in
First gear.
If you shif t into First position when
the vehicle speed is above 31 mph
(50 km/h), the transmission shif ts
into Second gear f irst to avoid
sudden engine braking.
If you exceed the maximum speed
f or the gear you are in, the engine
speed will enter into the tachometer’s
red zone. If this occurs, you may f eel
the engine cut in and out. This is
caused by a limiter in the engine’s
computer controls. The engine will
run normally when you reduce the
RPM below the red zone.
Use D to provide engine braking
when going down a steep hill. D
gives you more power and increased
engine braking.
5
4
3 4
3
3 3
Automatic Transmission
Driving
Drive(D,D) Second(2)First(1)
Engine Speed L imiter43
174

Set the Parking brake.
Make sure the ignition switch is in
the LOCK (0) position.
To release the Reverse Lockout,
make sure the ignition switch is in
the ACCESSORY (I) position. Put a cloth on the edge of the Shif tLock Release slot cover. Using a
key, caref ully pry on the edge of
the cover to remove it.
Insert the key in the Shift Lock
Release slot.
Push down on the key and move
the shift lever out of Park to
Neutral.To release the reverse lockout,
move the shift lever from Neutral
to Reverse, then to Park.
Remove the key from the Shift
Lock Release slot, then install the
cover. Press the brake pedal, and
restart the engine.
If you need to use the Shif t Lock
Release, it means your vehicle is
developing a problem. Have it
checked by an Acura dealer.
Do this if pushing on the brake pedal
does not shif t the transmission out of
Park. This procedure is also used to
release the Reverse Lockout.
1.
2.
3.
4.
5.6.
Automatic Transmission
Driving
Shif t L ock Release
175
COVER
SHIFT LOCK RELEASE SLOT

The Variable Torque Management
4WD System (VTM-4) automatically
transf ers varying amounts of engine
torque to the rear wheels under
lower traction conditions.
If more traction is needed when your
MDX is stuck, or is likely to become
stuck, you can use the VTM-4 Lock
button to increase torque to the rear
wheels.The vehicle must be stopped with
the engine running.
Move the shift lever to First (1),
Second (2), or Reverse (R) gear.
Press the VTM-4 Lock button.
The light in the button will come
on.
To get unstuck, apply light pressure
to the accelerator pedal. Do not spin
the f ront tires f or more than a f ew
seconds. Because of the amount of
torque applied to the rear tires, they
should not spin. This is normal. If
you are not able to move the vehicle,
stop and reverse direction. do
one of the f ollowing: Press the VTM-4 Lock button.
Move the shift lever to D , D or
D.
Turn the ignition switch to LOCK
(0).
The VTM-4 Lock will temporarily
disengage when the vehicle speed
exceeds 18 mph (30 km/h). It will
automatically engage again as the
speed slows below 18 mph (30
km/h). The button light will remain
on.
1.
2.
3.
54
3
To Engage the VTM-4 Lock To Disengage the VTM-4 Lock,
VTM-4 System
Driving176
NOTICE: NOTICE:
Do not use the VTM-4 Lock
button on dry, paved roads. Driving on
dry, paved roads with VT M-4 Lock ON
may damage the rear dif f erential when
making a turn. Strange noise and
vibration can also result. Do not continuously spin the
f ront tires of your MDX. Continuously
spinning the f ront tires can cause
transmission or rear dif f erential
damage.

Your Acura is equipped with a Tire
Pressure Monitoring System
(TPMS) that turns on every time you
start the engine and monitors the
pressure in your tires while driving.
Each tire has its own pressure
sensor. If the air pressure of a tire
becomes signif icantly low, the
sensor in that tire immediately sends
a signal that causes the low tire
pressure indicator and the
appropriate tire on the Tire Pressure
Monitor to come on.Driving on a signif icantly under-
inf lated tire causes the tire to
overheat and can lead to tire failure.
Under-inf lation also reduces f uel
efficiency and tire tread life, and may
af f ect the vehicle’s handling and
stopping ability.
When the tire pressure monitoring
system warning light is lit, one or
more of your tires is signif icantly
under-inf lated. You should stop and
check your tires as soon as possible,
and inflate them to the proper
pressureasindicatedonthevehicle’s
tire inf ormation placard. Each tire, including the spare should
be checked monthly when cold and
set to the recommended inf lation
pressure as specif ied in the vehicle
placard and owner’s manual (see
page ).
Although your tire pressure is
monitored, you must manually check
thetirepressuresmonthly.
If you think you can saf ely drive a
short distance to a service station,
proceed slowly to the station and
inflate the tire to the recommended
pressure shown on the driver’s
doorjamb.
If the tire is f lat, or if the tire
pressure is too low to continue
driving, replace the tire with the
compact spare tire.
222
Tire Pressure Monitoring System (TPMS)
Driving
Low Tire Pressure
Indicator
177

The appropriate tire indicator and
Low Tire Pressure Indicator will
come on if a tire becomes
signif icantly underinf lated. Follow
the instructions under ‘‘Low Tire
Pressure Indicator’’.The indicator comes on and stays on
when there is a problem with the
Tire Pressure Monitoring System.
If this happens, the system will shut
of f and no longer monitor tire
pressures. Have the system checked
by an Acura dealer as soon as
possible.
If you have a f lat tire, the Low Tire
Pressure and Tire monitor indicators
will come on. Replace the indicated
flat tire with the compact spare tire
(see page ).Each wheel is equipped with a tire
pressure sensor mounted inside the
tire behind the valve stem. You must
use TPMS specif ic wheels. It is
recommended that you always have
your tires serviced by your Acura
dealer or qualif ied technician.
Af ter you replace the f lat tire, the
Low Tire Pressure indicator will stay
on.Thisisnormal;thesystemisnot
monitoring the spare tire pressure.
Manually check the spare tire
pressure to be sure it is correct.
Never use a puncture-repairing agent
in a f lat tire. If used, you will have to
replace the tire pressure sensor.
Havetheflattirerepairedbyan
Acura dealer as soon as possible.
231
Tire Pressure Monitoring System (TPMS)
Driving
Tire Pressure Monitor
Tire Pressure Monitoring
System (T PMS) Indicator
ChangingtheTirewithTPMS
178

Always use the parking brake when
you park your vehicle. Make sure
the parking brake is set f irmly or
your vehicle may roll if it is on an
incline.
Set the parking brake bef ore you put
the transmission in Park. This keeps
the vehicle from moving and putting
pressure on the parking mechanism
in the transmission.Make sure the moonroof and the
windows are closed.
Turn of f the lights.
Place any packages, valuables, etc.
in the cargo area, or take them
with you.
Lock the doors.
Never park over dry leaves, tall
grass, or other f lammable
materials. The hot three way
catalytic converter could cause
these materials to catch on fire.If the vehicle is f acing uphill, turn
the f ront wheels away f rom the
curb.
If the vehicle is f acing downhill,
turn the front wheels toward the
curb.
Make sure the parking brake is
f ully released bef ore driving away.
Driving with the parking brake
partially set can overheat or
damage the rear brakes.
Parking T ips
Parking
Driving179

Resting your f oot on the pedal keeps
the brakes applied lightly, builds up
heat, and reduces their ef f ectiveness.
It also keeps your brake lights on all
the time, conf using drivers behind
you.
Constant application of the brakes
when going down a long hill builds
up heat and reduces their ef f ective-
ness. Use the engine to assist the
brakes by taking your f oot of f the
accelerator and downshif ting to a
lower gear.Check the brakes after driving
through deep water. Apply the
brakes moderately to see if they f eel
normal. If not, apply them gently and
f requently until they do. Be extra
cautious in your driving.
The hydraulic system that operates
the brakes has two separate circuits.
Each circuit works diagonally across
the vehicle (the lef t-f ront brake is
connected with the right-rear brake,etc.). If one circuit should develop a
problem, you will still have braking
at two wheels.
If the brake pads need replacing, you
will hear a distinctive, metallic
screeching sound when you apply
the brake pedal. If you do not have
the brake pads replaced, they will
screech all the time. It is normal f or
the brakes to occasionally squeal or
squeak when you apply them.
Your vehicle is equipped with disc
brakes at all f our wheels. A power
assist helps reduce the ef f ort needed
on the brake pedal. The ABS helps
you retain steering control when
braking very hard.
Braking System DesignBrake Wear Indicators
Braking System
Driving180
Front