2003 TOYOTA MATRIX Navigation Manual

Corolla_MATRIX_Navi_U (L/O 0208)
332003 MY COROLLA MATRIX (OM12774U)
SSNU187
The voice guidance provides various mes-
sages as you approach an intersection, or
other points where you need to maneuver
the vehicle.
1“Proceed about 5 miles.”
2“In a half of a mile, right turn.”
3“Next right.”
4(Beep sound only)
INFORMATION
On freeways, interstates or other
highways with higher speed limits,
the voice guidance will be made at
earlier points than on city streets in
order to allow time to maneuver.
SSNU188
1“Proceed about 4 miles to the
traffic circle.”
2“In a half of a mile, traffic circle
ahead, and then the 3rd exit.”
3“The 3rd exit ahead.”
4(Beep sound only)
5“The exit ahead.”
6(Beep sound only)
Typical voice guidance
prompts

Corolla_MATRIX_Navi_U (L/O 0208)
342003 MY COROLLA MATRIX (OM12774U)
EMV3114U
∗: The system indicates a U−turn if the
distance between two one −way roads (of
opposite directions) is less than 15 m (50
ft.) in residential areas or 50 m (164 ft.)
in non− residential areas.
1“In half of a mile, make a legal
U−turn ahead.”
2“Make a legal U −turn ahead.”
3(Beep sound only)
EMV3115U
The system announces your approach to
the final destination.
1“Your destination is ahead.”
2“You have arrived at your des-
tination. Your route guidance is
now finished.”
INFORMATION
 Voice guidance may be made early
or delayed.
 If the system cannot determine the
current position correctly, you may
not hear voice guidance or may not
see the magnified intersection on
the screen.
 If you did not hear voice guidance
command, push the
“MAP” or
“NAV” button to hear it again.

Corolla_MATRIX_Navi_U (L/O 0208)
352003 MY COROLLA MATRIX (OM12774U)
If you register your home address be-
forehand, you can easily set the route
back to your home.
1NAN109
1. Push the “MENU” button to dis-
play the “Menu” screen and select
the
“Marked points” switch.
1NAN065
2. Select the “Reg. home” switch
for registering your home address.
If your home is already registered, the
“Reg. home” switch changes to the
“Delete home” switch.
1NAN110
You may register the location of your
home by some different methods: cur-
rent position, address, map location,
etc. Select your desired method from
the menu on the screen.
Input your home in the same way as the
destination input. (See page 23.)
Registration of your home

Corolla_MATRIX_Navi_U (L/O 0208)
362003 MY COROLLA MATRIX (OM12774U)
Deleting your home
1NAN111
1. Push the “MENU” button to dis-
play the “Menu” screen and select
the
“Marked points” switch.
1NAN068
2. Select the “Delete home” switch.
The screen changes and displays the map
location of the home and a message. If
you are sure, select the
“Yes” switch. If
not, the
“No” switch. When you are driving while the route
guidance is operating, you can change
the route to detour around a section of
the route where a delay is caused by
road repairs, an accident, etc.
1NAN069
Select the “Chg.route” switch on the
right side of the screen if you encoun-
ter a reason to divert from the selected
route.
Detour setting

Corolla_MATRIX_Navi_U (L/O 0208)
372003 MY COROLLA MATRIX (OM12774U)
EMV3065U
This picture shows an example of how the
system would route you around a delay
caused by a traffic jam.
1This part indicates the location where
traffic jam is occurring due to road
repairs or an accident.
2These show the detour route sug-
gested by the system.
1NAN070
When you select the “Chg.route”
switch, the screen changes to the
“Change route” screen that allows you to
select the distance you want to detour.
Select one of the numeral keys to start
the detour process. After detouring, the
system returns to the original guidance
route. “Whole route”:
If you select this switch,
the system will calculate an entire new
route to the destination.
INFORMATION
 When your vehicle is on a freeway,
the detour distance selections are 5,
15, and 25 miles.
 The system may not be able to cal-
culate a detour route depending on
the selected distance and surround-
ing road conditions.
“Search condition”: To change the condi-
tions of the searching route. (See page
67.)
“Quick”: A route on which you can reach
the destination in the shortest time.
“Short”: A route on which you can reach
the destination in the shortest distance.
“Alternative”: Other route.

Corolla_MATRIX_Navi_U (L/O 0208)
382003 MY COROLLA MATRIX (OM12774U)
Points of interest such as gas stations
and restaurants can be displayed on
the map screen. You can also set their
location as a destination and use them
for route guidance.
1NAN071
To display a particular type of point of
interest on the screen, select the
“POI” switch on the map right side of
the screen.
1NAN072
A window with a limited choice of points
of interest will be displayed. When you
select your desired type of point of inter-
est, icons will appear on the map screen
indicating where the POI addresses are
located.
“More”: If you cannot find your desired
point of interest on the limited choice
screen, select this switch. The screen
then displays the more “Point of interest”
listing screen.
You can show up to 5 types of icons on
the screen.
1NAN073
When you select the point of interest type
from more list, the screen will display the
complete “Point of interest” listing screen.
1NAN074
Selecting the “Delete” switch will de-
lete the last selected icon.
Displaying points of interest

Corolla_MATRIX_Navi_U (L/O 0208)
392003 MY COROLLA MATRIX (OM12774U)
1NAN075
When you select a point of interest type
from either the limited list or the complete
list, the screen will display icons at those
locations on the map screen.
1NAN076
“Local POI list”: Select this switch while
selecting some categories of POI. The
“Local POI list” screen will appear with a
list of the points within 20 miles.
Sort by “Dist.”: Select this switch to list
the points of interest in order of the dis-
tance.
Sort by “Icon”: Select this switch to list
the points of interest in order of the type
of symbol.
Sort by “Name”: Select this switch to list
the points of interest in alphabetical order.
“Route”: Select this switch to list the
points of interest on the route in order of
the distance.
To turn off the icons of the points of
interest on the map screen, select the
“POI off” switch on the screen
“Show POI icons”. Setting a POI as a destination
You can select one of the points of
interest icons on the map screen as a
destination and use it for a route guid-
ance.
1NAN077
1. Select the icon of the point of inter-
est that you want to set as a des-
tination.
Operate the select and scroll lever to
move the cursor
your desired POI
icon. Then the icon “POI” is centered in
the screen and it overlaps with the cursor
.

Corolla_MATRIX_Navi_U (L/O 0208)
402003 MY COROLLA MATRIX (OM12774U)
1NAN078
2. Push the “ENT” button, and then
the switch menu appears.
3. Select the
“Guide” switch.
1NAN079
The name of the point of interest is dis-
played at the top of the screen. You can
select the other POI icon on the displayed
map.
When you push the
“ENT” button, the
information such as the name and ad-
dress, etc. are displayed.
1NAN080
4. If you set the point of interest as a
destination, select the
“Enter ”
switch. If not, push the “BACK”
button, then the previous screen re-
turns.