2003 TOYOTA AVENSIS manual radio set

MO
NEW MODEL OUTLINEMO-29


: Standard OP: Option
EuropeGeneral
ENTRYMID
TECHNICALMID
ELEGANTGeneralCountries
Body Electrical
HeadlightProjector



HeadlightHID (High lntensity Discharge)ÐOPOPÐ
Headlight BeamManual


Ð
Level Control SystemAutomaticÐOPOPÐ
Headlight Cleaner SystemOP*5OPOPÐ
FrontExcept for 1AZ-FEOP

Ð
Fog LightFront1AZ-FEÐOPOPOP*4
Rear


Ð
Illuminated Entry System




Navigation SystemÐOPOPÐ
Multi information DisplayOP

Ð
8-speaker OnlyOPOPOPOP
Audio SystemRadio / CD / Cassette / 8-speaker




Steering Switch


Ð
Manual
ÐÐ

Air ConditionerAutomaticÐ

Ð
WithoutOPÐÐOP
Conventional TypeExcept for 1CD-FTV




HeaterPTC Type1CD-FTVOPÐÐÐHeaterHot Gas Type1CD-FTV


Ð
Combustion TypeLHD of 1CD-FTVÐOPOPÐ
WiperFrontAdjustment Interval INT Function
ÐÐ
Wiper
SystemFrontRaindrop Sensing FunctionÐ

ÐSystemRearIntermittent FunctionLiftback & Wagon


Ð
Power Window
Front Door One-Motion Auto Up-and-Down,
Jam Protection Function
ÐÐ

SystemAll-Door One-Motion Auto Up-and-Down,
Jam Protection FunctionOP

OP
Door Lock ControlPower Door Look Control System



Door Lock Control
SystemWireless Door Look Remote Control System


ÐSystemDouble Locking SystemExcept for 1AZ-FE & LHD


Ð
Engine ImmobiliserExcept for 1AZ-FE



System1AZ-FEÐOPOPÐ
Theft Deterrent SystemExcept for 1AZ-FE & 1CD-FTV


Ð
5
Driver & Front Passenger & SideExcept for 1AZ-FEOPÐÐÐ
SRS*5 Airbag& Knee Airbags1AZ-FEÐ



SystemDriver & Front Passenger & SideExcept for 1AZ-FE



& Knee & Curtain Shield Airbags1AZ-FEÐOPOPÐ
Cruise Control System1AZ-FSE & 1CD-FTVÐOPOPÐ
Outside RearElectrical Retractable with HeaterÐ

Ð
View MirrorElectrical RetractableÐÐÐ

Inside RearAutomatic Glare-Resistant EC (Electrical) TypeÐ

Ð
View MirrorManual Glare-Resistant Type
ÐÐ

Power Tilt Up-and-Sliding Moon RoofExcept for 1AZ-FSEOPOPOPÐ
(with Jam Protection Function)1AZ-FSEÐOP*6OP*6Ð
*4: LHD Models
*5: Supplemental Restraint System
*6: Except for Automatic Transaxle of Wagon Models
http://vnx.su

D26613
Example:
D25080
Negative (±)
Terminal
±
INTRODUCTION REPAIR INSTRUCTION
01±15
AVENSIS REPAIR MANUAL (RM1018E)
(8) Oil or water should not be put on the front seat outer belt and the front seat outer belt should be
cleaned with the appropriate detergents.
(i) AIRBAG SENSOR ASSEMBLY (1) Never reuse the airbag sensor assembly involved in a collision where the\
SRS has deployed.
(2) The connectors to the airbag sensor assembly should be connected or disc\
onnected with thesensor mounted on the floor. If the connectors are connected or disconnected while the airbag
sensor assembly is not mounted to the floor, it could cause an undesired ignition of the supple-
mental restraint system.
(3) Work must be started after 90 seconds from the time the ignition switch is t\
urned to the ºLOCKº position and the negative (±) terminal cable is disconnected from the battery, even if only loosen-
ing the set bolts of the airbag sensor assembly.
(j) WIRE HARNESS AND CONNECTOR
(1) The SRS wire harness is integrated with the instrument panel wire harness a\
ssembly. All connec-tors in the system are a standard yellow color. If the SRS wire harness becomes disconnected
or the connector becomes broken due to an accident, etc., repair or repl\
ace it.
3. ELECTRONIC CONTROL
(a) REMOVAL AND INSTALLATION OF BATTERY TERMI-NAL
(1) Before performing electronic work, disconnect thebattery negative (±) terminal cable beforehand in
order to prevent it from shorting and burning out.
(2) When disconnecting and insta lling the terminal
cable, turn the ignition switch and lighting switch
OFF, and loosen the terminal nut completely. Per-
form these operations without twisting or prying the
terminal.
(3) When the battery terminal cable is removed, the memories of the clock, radio, DTCs, etc. are erased.
So before removing it, check them and make a note
of their settings.
(4) When the battery negative (±) terminal cable is dis- connected, memories of various systems are
erased. Therefore, refer to the PRE±CHECK for
each system to make sure whether or not the sys-
tem needs to be initialized after the battery negative
http://vnx.su

022KX±01
±
PREPARATION AUDIO & VISUAL SYSTEM
02±55
AVENSIS REPAIR MANUAL (RM1018E)
AUDIO & VISUAL SYSTEM
PREPARATION
Recomended Tools
09042±00010Torx Socket T30NAVIGATION ANTENNA ASSY
09042±00030Torx Socket T20CIGARETTE LIGHTER ASSY
09050±00032Air DrillFRONT NO.1 SPEAKER ASSY
REAR SPEAKER ASSY
(09050±00210)Chuck SetFRONT NO.1 SPEAKER ASSY
REAR SPEAKER ASSY
(09050±00220)HandleFRONT NO.1 SPEAKER ASSY
REAR SPEAKER ASSY
09050±20010Air RiveterFRONT NO.1 SPEAKER ASSY
REAR SPEAKER ASSY
(09050±02010)Dust CapFRONT NO.1 SPEAKER ASSY
REAR SPEAKER ASSY
(09050±02020)Nose Piece No.1FRONT NO.1 SPEAKER ASSY
REAR SPEAKER ASSY
09060±60350Revet CutterFRONT NO.1 SPEAKER ASSY
REAR SPEAKER ASSY
09070±20010Moulding RemoverRADIO RECEIVER ASSY
ANTENNA CORD SUB±ASSY
POWER POINT SOCKET ASSY
NAVIGATION ANTENNA ASSY
ANTENNA CORD SUB±ASSY NO.3
AMPLIFIER ANTENNA
ASSY(LIFTBACK MODELS)
AMPLIFIER ANTENNA ASSY(SEDAN
MODELS)
AMPLIFIER ANTENNA
ASSY(WAGON MODELS)
Equipment
Torque wrench
http://vnx.su

031H2±01
±
SERVICE SPECIFICATIONS ENGINE MECHANICAL
03±15
AVENSIS REPAIR MANUAL (RM1018E)
TORQUE SPECIFICATION
1ZZ±FE/3ZZ±FE:
Part TightenedN
mkgf
cmft
lbf
Camshaft bearing cap No. 3 x Cylinder head sub±assy1313310
Camshaft bearing cap No. 1 x Cylinder head sub±assy2323517
Camshaft timing gear or sprocket x Camshaft No. 25455140
Chain tensioner assy No. 1 x Timing chain or belt cover sub±assy9.09280 in.
lbf
V±ribbed belt tensioner assy x Cylinder block sub±assy6970451
V±ribbed belt tensioner assy x Cylinder head sub±assy2929621
Engine mounting insulator RH x Body5253038
Engine mounting insulator RH x Transverse engine engine mounting bracket5253038
Cylinder head cover sub±assy x Cylinder head sub±assy A
B11
9.011 2 928
80 in.
lbf
Cylinder head cover sub±assy x Timing chain or belt cover sub±assy1111 28
Ignition coil assy x Cylinder head cover sub±assy9.09280 in.
lbf
Engine wire x Cylinder head cover sub±assy9.09280 in.
lbf
Cylinder head cover No. 2 x Cylinder head cover sub±assy7.07162 in.
lbf
Engine hanger x Cylinder head sub±assy3838728
Radio setting condenser x Cylinder head sub±assy101027
Engine coolant temperature sensor x Cylinder head sub±assy2020415
Exhaust manifold x Cylinder head sub±assy3737727
Exhaust manifold heat insulator No. 1 x Exhaust manifold Bolt
Nut18
12184
12213 9
Manifold stay No. 2 x Exhaust manifold4950036
Manifold stay No. 2 x Cylinder block sub±assy4950036
Manifold stay x Exhaust manifold A4950036
Manifold stay x Cylinder block sub±assyB3737727
Transverse engine engine mounting bracket x Timing chain or belt cover
sub±assy4747935
V±ribbed idler assy No.1 x Cylinder block sub±assy39.240029
Knock sensor x Cylinder block sub±assy2020415
Crankshaft position sensor x Timing chain or belt cover9.09280 in.
lbf
Camshaft position sensor x Cylinder head sub±assy9.09280 in.
lbf
Water inlet x Cylinder block sub±assy1111 28
Water by±pass pipe No. 1 x Cylinder block sub±assy9.09280 in.
lbf
Water by±pass pipe No. 1 x Cylinder head sub±assy9.09280 in.
lbf
Oil level gage guide x Water by±pass pipe No. 11313310
Intake manifold x Cylinder head sub±assy3030622
Flywheel sub±assy x Crankshaft 1st
2nd49
Turn 90
500
Turn 90
36
Turn 90

Drive plate & ring gear sub±assy x Crankshaft8889765
Transverse engine engine mounting bracket front x Transverse engine en-
gine mounting insulator front5253038
Transverse engine engine mounting bracket rear x Transverse engine engine
mounting insulator rear8788764
Transverse engine engine mounting bracket LH x Transverse engine engine
mounting insulator LH8081659
Transverse engine engine mounting bracket RH x Transverse engine engine
mounting insulator RH5253038
Front suspension crossmember sub±assy x Body A
B45
133459
1,35633
98
Front suspension member brace x Body Bolt A
Bolt B133 801,356 81698
59
http://vnx.su

A76707
Water By±pass Hose No. 2
Radiator Hose Inlet
Heater Inlet Water Hose
Gasket
Exhaust Manifold
Manifold Stay Exhaust Manifold
Heat Insulator No. 1


Gasket
Engine Coolant
Temperature Sensor

Non±reusable part
N´m (kgf´cm, ft´lbf) : Specified torque
20 (204, 15)
9.0 (92, 80 in.
lbf)
37 (377, 27)
18 (184, 13)
49 (500, 36)
Clamp Bracket
10 (102, 7)
Radio Setting Condenser
V±Ribbed Idler Assy No. 1
Tube
18 (184, 13)
12 (122, 9)
Manifold Stay No. 2
49 (500, 36)
37 (377, 27)18 (184, 13)
39.2 (400, 29)
14±26
±
ENGINE MECHANICAL PARTIAL ENGINE ASSY (1ZZ±FE/3ZZ±FE)
AVENSIS REPAIR MANUAL (RM1018E)
http://vnx.su

A76722
A76723
A64033
A64034
A64034
±
ENGINE MECHANICAL PARTIAL ENGINE ASSY (1ZZ±FE/3ZZ±FE)
14±37
AVENSIS REPAIR MANUAL (RM1018E)
85. REMOVE EXHAUST MANIFOLD HEAT INSULATOR
NO.1
(a) Disconnect the heated oxygen sensor connector.
(b) Remove the 3 bolts and the nut, and then remove the ex-
haust manifold heat insulator.
86. REMOVE EXHAUST MANIFOLD
(a) Remove the 5 nuts, then remove the exhaust manifold and the gasket.
87. REMOVE ENGINE COOLANT TEMPERATURE SENSOR
(a) Using SST, remove the engine coolant temperature sen- sor.
SST 09817±33190
88. REMOVE RADIO SETTING CONDENSER
(a) Remove the bolt and the condenser.
89. REMOVE WATER BY±PASS HOSE NO.2
90. REMOVE RADIATOR HOSE INLET
91. REMOVE HEATER INLET WATER HOSE
92. REPLACE PARTIAL ENGINE ASSY
93. INSTALL RADIO SETTING CONDENSER
(a) Install the condenser with the bolt. Torque: 10 N
m (102 kgf
cm, 7 ft
lbf)
http://vnx.su

670S4±01
±
AUDIO & VISUAL SYSTEM AUDIO & VISUAL SYSTEM
67±1
AVENSIS REPAIR MANUAL (RM1018E)
AUDIO & VISUAL SYSTEM
PRECAUTION
1. OBSERVE HANDLING AND OPERATIONAL PRECAUTIONS
(a) Please explain to the customer that when the negative terminal is disconnected from the batter\
y, the
channel information memory of the AM/FM broadcast stations in the radio receive\
r is cleared. If neces-
sary, make a note of the recorded channel information before the negative ter\
minal is disconnected,
then reset the information after the negative terminal is reconnected.
(b) The removal/installation of the radio receiver should be performed after al\
l the cassette tapes and au- dio CDs are ejected from the radio receiver.
HINT:
If the cassette tapes and the audio CDs cannot be ejected due to the malfu\
nction of the radio receiver, do
not try to drag them out by force. Bring the vehicle to the repair plant\
.
(c) Fasten the earth bolt securely when the antenna cord is removed or insta\
lled.
HINT:
Failing to fasten the earth bolt securely causes noise at the time of ra\
dio wave reception.
(d) Do not touch the cone paper of the speaker.
http://vnx.su