2003 TOYOTA AVENSIS light
[x] Cancel search: lightPage 7 of 2234
MO
NEW MODEL OUTLINE
\b
\b
\b
Sedan and Liftback Models
Wagon Model
Headlight
(High Beam)
Clearance Light Turn
Signal Light
Headlight Cleaner Headlight
(Low Beam)
MO-7
EXTERIOR
Front View
The front view is dynamically expressive, with innovative headlights and\
a front bumper design
that has a sense of stability with upper and lower thickness.
The headlight low beams feature projectors and have an innovative shape.\
http://vnx.su
Page 8 of 2234
NEW MODEL OUTLINE
\b
\b
Taillight
Stop
Light Turn Signal Light Back Up or
Rear Fog Light
\b
\b
Turn Signal Light
Stop
Light Taillight Back Up or
Rear Fog Light
\b
\b
Tail and Stop Light
Turn Signal Light Back Up or Rear Fog Light
MO-8
Rear View
The rear combination lens features an elegant, innovative shape.
The luggage compartment door and back door were given a greater sense of\
volume for a
high-quality feel.
4-Door Sedan
5-Door Liftback
5-Door Wagon
http://vnx.su
Page 23 of 2234
MO
NEW MODEL OUTLINE
\b
\b
\b
\b
Windshield
Glass Front Door
Glass Back Window
Glass
Rear Door
Glass
Sedan Model
Rear Door
Glass
Back Door
Glass
Liftback Model
Rear Quarter Glass
(OPT: Privacy Glass) Back Door Glass
(OPT: Privacy Glass)
Rear Door Glass
(OPT: Privacy Glass)
Wagon Model
MO-21
Windshield & Door Glass
Dark gray privacy glass is available as an option for the rear door glas\
s, rear quarter glass, and
back door glass of wagon models.
Glass Portion Provided
Glass TypeUV Reduction Rate (%)
(as reference) Visible Light Penetration (%)
(as reference)
Windshield Standard Green Laminated 100 %70 % Min.
Front Door Standard Green82 % 70 % Min.
Rear DoorStandardGreen 82 % 70 % Min.Rear DoorOption (Wagon only) Privacy 96 %24 %
Rear Quarter Standard
Green 82 % Ð
(Wagon only) OptionPrivacy 96 % Ð
Back Window Standard
Green 78 % 70 % Min.
or Back Door Option (Wagon only) Privacy 96 %20 %
http://vnx.su
Page 30 of 2234
NEW MODEL OUTLINEMO-28
EQUIPMENT LIST
: Standard OP: Option
EuropeGeneral
ENTRYMID
TECHNICALMID
ELEGANTGeneral
Countries
Exterior
Rear SpoilerWagonÐ
Side Protection MouldingOPOPOPOP
WindshieldGreenÐ
Front SideGreen
GlassRear Side & BackGreenGlassRear Side & BackWagonPrivacyOPOPOPÐ
Rear QuarterWagonGreenÐRear QuarterWagonPrivacyOPOPOPÐ
Chassis
195/65 R153ZZ-FE & 1ZZ-FE & 1AZ-FE
205/55 R161AZ-FSE & 1CD-FTVÐ
Tire205/55 R163ZZ-FE & 1ZZ-FE & 1AZ-FEOPOPOPOP
215/45 R171AZ-FEÐOPOPÐ215/45 R171AZ-FSEÐOPOPÐ
15 x 6J Steel3ZZ-FE & 1ZZ-FE & 1AZ-FE
16x61/2J Steel1AZ-FSE & 1CD-FTVÐ16 x 6 1/2 J Steel3ZZ-FE & 1ZZ-FE & 1AZ-FEOPOPOPOP
Disc Wheel16 x 6 1 / 2 JJ AluminumOPOPOPOP
16 x 6 1 / 2 JJ Light Weight AluminumOPOPOPOP
17 x 7JJ Aluminum1AZ-FEÐOPOPÐ17 x 7JJ Aluminum1AZ-FSEÐOPOPÐ
ABS (Anti-lock Brake System) with EBD (Electronic Brake force Distrib\
ution)
VSC (Vehicle Stability Control) & Brake1AZ-FSEÐ(y)Assist & TRC (Traction Control)1CD-FTVOPOPOPÐ
Wheel4-Spoke UrethaneÐÐWheel4-Spoke LeatherÐÐ
SteeringColumnManual Tilt & TelescopicSteeringEPS*13ZZ-FE & 1ZZ-FEÐ
Hydraulic Type Power
Steering1AZ-FSE & 1CD-FTV & 1AZ-FE
Body
CoverFabricCoverLeather1AZ-FSE & 1CD-FTVÐOPOPÐ
FrontManual
SeatFrontPower1AZ-FSE & 1CD-FTVÐOPOPÐ
FixSedanÐÐÐ
Rear60:40 FoldingSedanÐ
60:40 Double FoldingLiftback & WagonÐ
SeatBelt
Front3-Point ELR*2 Electrical Sensing Type Pretensioner
& Force Limiter
BeltRear3-Point ELR*2 & ALR*3
CRS (Child Restraint System) Anchor System (Rear Outside Seat Only)
*1: Electoronic Power Steering
*2: Emergency Locking Retractor
*3: Automatic Locking Retractor
http://vnx.su
Page 31 of 2234
MO
NEW MODEL OUTLINEMO-29
: Standard OP: Option
EuropeGeneral
ENTRYMID
TECHNICALMID
ELEGANTGeneralCountries
Body Electrical
HeadlightProjectorHeadlightHID (High lntensity Discharge)ÐOPOPÐ
Headlight BeamManualÐ
Level Control SystemAutomaticÐOPOPÐ
Headlight Cleaner SystemOP*5OPOPÐ
FrontExcept for 1AZ-FEOPÐ
Fog LightFront1AZ-FEÐOPOPOP*4
RearÐ
Illuminated Entry System
Navigation SystemÐOPOPÐ
Multi information DisplayOPÐ
8-speaker OnlyOPOPOPOP
Audio SystemRadio / CD / Cassette / 8-speaker
Steering SwitchÐ
ManualÐÐ
Air ConditionerAutomaticÐÐ
WithoutOPÐÐOP
Conventional TypeExcept for 1CD-FTV
HeaterPTC Type1CD-FTVOPÐÐÐHeaterHot Gas Type1CD-FTVÐ
Combustion TypeLHD of 1CD-FTVÐOPOPÐ
WiperFrontAdjustment Interval INT FunctionÐÐWiper
SystemFrontRaindrop Sensing FunctionÐÐSystemRearIntermittent FunctionLiftback & WagonÐ
Power Window
Front Door One-Motion Auto Up-and-Down,
Jam Protection FunctionÐÐ
SystemAll-Door One-Motion Auto Up-and-Down,
Jam Protection FunctionOPOP
Door Lock ControlPower Door Look Control SystemDoor Lock Control
SystemWireless Door Look Remote Control SystemÐSystemDouble Locking SystemExcept for 1AZ-FE & LHDÐ
Engine ImmobiliserExcept for 1AZ-FE
System1AZ-FEÐOPOPÐ
Theft Deterrent SystemExcept for 1AZ-FE & 1CD-FTVÐ
5
Driver & Front Passenger & SideExcept for 1AZ-FEOPÐÐÐ
SRS*5 Airbag& Knee Airbags1AZ-FEÐ
SystemDriver & Front Passenger & SideExcept for 1AZ-FE
& Knee & Curtain Shield Airbags1AZ-FEÐOPOPÐ
Cruise Control System1AZ-FSE & 1CD-FTVÐOPOPÐ
Outside RearElectrical Retractable with HeaterÐÐ
View MirrorElectrical RetractableÐÐÐ
Inside RearAutomatic Glare-Resistant EC (Electrical) TypeÐÐ
View MirrorManual Glare-Resistant TypeÐÐ
Power Tilt Up-and-Sliding Moon RoofExcept for 1AZ-FSEOPOPOPÐ
(with Jam Protection Function)1AZ-FSEÐOP*6OP*6Ð
*4: LHD Models
*5: Supplemental Restraint System
*6: Except for Automatic Transaxle of Wagon Models
http://vnx.su
Page 51 of 2234
010B8±08
D25086
WRONGCORRECT
D25087
Looseness of CrimpingCore Wire Terminal
Deformation
Pull Lightly
01±32
±
INTRODUCTION HOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMS
AVENSIS REPAIR MANUAL (RM1018E)
ELECTRONIC CIRCUIT INSPECTION PROCEDURE
1. BASIC INSPECTION
(a) RESISTANCE MEASURING CONDITION OF ELECTRONIC PARTS (1) Unless stated, all resistance is measured at an ambient temperature of 20 C (68 F). As the re-
sistance may be outside the specifications if measured at high temperatures imme\
diately after
the vehicle has been running, measurements should be made when the engine h\
as cooled
down.
(b) HANDLING OF CONNECTOR(1) When removing the connector with lock, press the
connector in the direction of the engagement and
remove the lock by lightly pressing the lock claw.
(2) When removing the connector, do not hold the har- ness, but hold the connector.
(3) Before connecting the connector, check that there is no deformation, damage or missing terminals.
(4) The connector with a lock should be securely con- nected until it makes a ºclickº sound.
(5) When checking the connector with a Toyota electri- cal tester, check it from the backside (harness side)
of the connector using a mini test lead.
NOTICE:
As a water proof connector cannot be checked from
the backside, check by connecting the sub±harness.
Do not damage the terminals by moving the inserted
tester needle.
(c) CONNECTOR CHECKING POINTS
(1) Checking when the connector is connected:By holding the connector, check the inserted condi-
tion and locking efficiency (engaged condition).
(2) Checking when the connector is removed: Check by lightly pulling the wire harness (missing
terminal, terminal crimping condition, core wire
break).
Check visually for any rust, metal particles, water
and bent terminals (rust, mixing of foreign object,
terminal deformation).
NOTICE:
When testing a gold±plated female terminal, always use a
gold±plated male terminal.
http://vnx.su
Page 53 of 2234
Z17005
Fig. 2
Sensor
C BA
ECU
1 2 1
2 2
1
B04722
Fig. 3
Sensor
B2
A
1
2 1
2 21
C
B1
1
2 ECU
Z17007
Fig. 4
Sensor
C BA
1
2 1
2 2
15V
5V
0V
01±34
±
INTRODUCTION HOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMS
AVENSIS REPAIR MANUAL (RM1018E)
(b) Check the continuity. (1) Disconnect connectors A and C and measure theresistance between them.
Resistance: 1 or less
HINT:
Measure the resistance while lightly shaking the wire harness
vertically and horizontally. In the case of Fig. 2:
Between terminal 1 of connector A and terminal 1
of connector C No continuity (open)
Between terminal 2 of connector A and terminal 2
of connector C Continuity
Therefore, the cause is an open circuit between ter-
minal 1 of connector A and terminal 1 of connector
C.
(2) Disconnect connector B and measure the resis-
tance between the connectors.
In the case of Fig. 3:
Between terminal 1 of connector A and terminal 1
of connector B1 Continuity
Between terminal 1 of connector B2 and terminal 1
of connector C No continuity (open)
Therefore, the cause is an open circuit between ter-
minal 1 of connector B2 and terminal 1 of connector
C.
(c) Check the voltage. (1) In a circuit in which voltage is applied (to the ECUconnector terminal), an open circuit can be checked
by conducting a voltage check.
As shown in Fig. 4, with each connector still con-
nected, measure the voltage between the body
ground and terminal 1 of connector A at the ECU 5
V output terminal, terminal 1 of connector B, and
terminal 1 of connector C, in that order.
(2) If the results are: 5 V: Between terminal 1 of connector A and body
ground
5 V: Between terminal 1 of connector B and body
ground
0 V: Between terminal 1 of connector C and body
ground
Therefore, the cause is an open circuit in the wire
harness between terminal 1 of connector B and ter-
minal 1 of connector C.
http://vnx.su
Page 54 of 2234
Z17008
CSHORT
1
2 B
1
2 1
2
A
Fig. 5
Z17009
Fig. 6
Sensor
C BA
ECU
1
2 1
2 2
1
Z17808
Fig. 7
Sensor B2
A
11 1
CB1
1ECU
2 22 2
±
INTRODUCTION HOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMS01±35
AVENSIS REPAIR MANUAL (RM1018E)
3. CHECK SHORT CIRCUIT
(a) If the wire harness is ground shorted as shown in Fig. 5,
locate the section by conducting a continuity check with
the body ground in step (b).
(b) Check the continuity with the body ground. (1) Disconnect connectors A and C and measure the
resistance between terminals 1 and 2 of connector
A and the body ground.
Resistance: 10 k or higher
HINT:
Measure the resistance while lightly shaking the wire harness
vertically and horizontally.
In the case of Fig. 6:
Between terminal 1 of connector A and body
ground Continuity (short)
Between terminal 2 of connector A and body
ground No continuity
Therefore, the cause is a short circuit between ter-
minal 1 of connector A and terminal 1 of connector
C.
(2) Disconnect connector B and measure the resis- tance between terminal 1 of connector A and the
body ground, and terminal 1 of connector B2 and
the body ground.
In the case of Fig. 7:
Between terminal 1 of connector A and body
ground No continuity
Between terminal 1 of connector B2 and body
ground Continuity (short)
Therefore, the cause is a short circuit between ter-
minal 1 of connector B2 and terminal 1 of connector
C.
http://vnx.su