2003 SUBARU IMPREZA change time

Audio
5-32
CAUTION
Do not attempt to insert two or more discs
into the slot at a time. Doing so can cause me-
chanical damage to the CD changer. Use only music CDs identified by a
mark. Do not use CDs listed below which could
cause damage to the CD player.
3-inch (8 cm) compact disc.
Any disc with a peel-off or seal on it.
Any disc with scratches and/or dust.
Bent disc.
Cleaning disc.
CD accessory. (E.g., 3-inch (8 cm) disc
adapter)
Do not insert or remove any disc when the
automatic transmission selector lever is in thepark position; the selector lever in that posi-tion can interfere with disc insertion or remov-al, causing scratches on the disc surface (for
AT vehicles).
To insert a disc
1. Press one of the “Disc select ” buttons (3) (num-
bered from 1 to 6) for which the disc indicator light(2) is “OFF”. The Disc indicator lights are located directly above
the corresponding
“Disc select ” buttons.
2. The indicator will begin blinking. The blinking willlast for 15 seconds.
During this period, insert a desired disc, and the
disc will begin to play. (If any disc is not inserted during this period, the “Disc slot ” (1) door will close.
Repeat step 1.)
Be sure to hold a disc with the label side (the side
where titles are printed) up.
3. To insert another disc, repeat step 1 and 2
choosing a different disc select button.
To insert six discs at a time
1. Press and hold the “Disc select ” button number 1
until all disc indicators begin blinking (about 1.5 se-conds).
2. The indicators will blink for 15 seconds. During
this period, insert desired six discs.
3. When all discs are loaded, the first disc will begin
to play. (If no disc is inserted within this 15 seconds,
the entire disc load sequence will be canceled.)
To remove a disc
1. Press the desired one of the “Disc select ” buttons
(3) (numbered from 1 to 6) for which the disc indica-tor light is on.
2. Press the “Eject button ” (4). The selected disc

Audio
5-33
– CONTINUED –
will be ejected and the indicator light will begin blinking.
3. To remove another disc, repeat step 1 and 2
choosing a different “Disc select ” button.
(To remove discs when the ignition switch is in the
“Lock” position, press the “Eject” button, and the
first disc will be ejected. Press the “Eject” button
again, and the next disc will be ejected and so on.At this time, the “Disc select ” buttons are disabled.)
To remove all discs at one time
1. Press and hold the “Eject” button (4) until all
“Disc” indicators begin blinking (about 1.5 se-
conds), and the first disc will be ejected.
2. When the disc is removed, the next one will be
ejected, and so on.
To replace a playing disc with another
Simply press the desired one of “Disc select ” but-
tons (3) (numbered from 1 to 6) or press the “DISC
select” button on the radio unit to select the desired
disc, and the disc will begin to play.
Disc indicators
Lit: when the corresponding storage tray is occu-pied by a disc.
Blinking: Disc player is either in loading, eject or
changing mode. OFF: No disc is loaded or the ignition switch is in the
“LOCK”
position.
n Open/Closed disc slot indicator
When the disc slot is open, the disc indicators onboth sides of the slot illuminate.
Function control
Refer to CD changer control operating instructions described in the “Type B audio set ” section.

Starting and operating
7-30
To temporarily cancel the cruise con- trol
There are four ways to cancel the cruise control tem- porarily: Depress the brake pedal.
Pull the control lever in the “CANCEL” direction. (if
so equipped) Depress the clutch pedal (manual transmission
vehicles only). Shift the selector lever into the “N” position (auto-
matic transmission vehicles only).
To resume the cruise control after it has been tem- porarily canceled and with vehicle speed of about
20 mph (32 km/h) or more, push the control lever
upward in the “ACCEL, RESUME ” direction to return
to the original cruising speed automatically.
To turn off the cruise control
There are two ways to turn off the cruise control: Push the main switch again.
Turn the ignition switch to the “ACC” or “LOCK”
position (but only when the vehicle is completely stopped).
To change the cruising speed
To increase the speed (by control lever)
Push the control lever upward in the “ACCEL, RE-
SUME” direction and hold it until the vehicle reaches
the desired speed. Then, release the control lever.
The vehicle speed at that moment will be memo-
rized and treated as the new set speed.
When the difference between the actual vehicle
speed and the set speed is less than 4 mph (6.8
km/h), the set speed can be increased 1 mph (1.6
km/h) each time by pressing the control lever up-
ward in the “ACCEL, RESUME ” direction quickly
within 0.5 second.
To increase the speed (by accelerator pedal)
1. Depress the accelerator pedal to accelerate the
vehicle to the desired speed.
2. Push the control lever downward in the “SET,
COAST” direction once. Now the desired speed is
set and the vehicle will keep running at that speed
without depressing the accelerator pedal.
NOTE
If the difference between the actual vehicle speed when the control lever is pushed down-ward and the speed last time you set is less than

Driving tips
8-29
– CONTINUED –
Gross Vehicle Weight (GVW) and Gross
Vehicle Weight Rating (GVWR)
Gross Vehicle Weight
The Gross Vehicle Weight (GVW) must never
exceed the Gross Vehicle Weight Rating (GVWR).
Gross Vehicle Weight (GVW) is the combined total of
the weight of the vehicle, driver, passengers, lug-gage, trailer hitch, trailer tongue load and any other
optional equipment installed on your vehicle. There-
fore, the GVW changes depending on the situation.
Determine the GVW each time before going on a tripby putting your vehicle and trailer on a vehiclescale.
Certification label
GVWR is shown on the certification label located on the driver ’s side door jamb of your vehicle.

Driving tips
8-35
– CONTINUED –
eral, state/province and/or other applicable regula- tions.
Trailer lights
Connection of trailer lights to your vehicle ’s electrical
system requires modifications to the vehicle ’s light-
ing circuit to increase its capacity and accommo-
date wiring changes. To ensure the trailer lights are
connected properly, please consult your SUBARU
dealer. Check for proper operation of the turn sig-nals, the brake lights and parking lights each timeyou hitch up.
CAUTION
Direct splicing or other improper connection
of trailer lights may damage your vehicle ’s
electrical system and cause a malfunction ofyour vehicle ’s lighting system.
Tires
Make sure that all the tires on your vehicle are prop-
erly inflated to the pressure specified on the tire
placard located on the left center pillar of your ve-hicle.
Trailer tire condition, size, load rating and proper
inflation pressure should be in accordance with the trailer manufacturer
’s specifications.
In the event your vehicle gets a flat tire when towing
a trailer, ask a commercial road service to repair the
flat tire.
If you carry a regular size spare tire in your vehicle
or trailer as a precaution against getting a flat tire,
be sure that the spare tire is firmly secured.
WARNING
Never tow a trailer when the temporary spare tire is used. The temporary spare tire is not
designed to sustain the towing load. Use ofthe temporary spare tire when towing canresult in failure of the spare tire and/or less
stability of the vehicle.
Trailer towing tips
CAUTION
Never exceed 45 mph (72 km/h) when tow-
ing a trailer in hilly country on hot days. When towing a trailer, steering, stability,
stopping distance and braking performancewill be different from normal operation. For

Driving tips
8-36
safety’s sake, you should employ extra cau-
tion when towing a trailer and you should
never speed. You should also keep the follow-ing tips in mind:
Before starting out on a trip
Check that the vehicle and vehicle-to-hitch mount-
ing are in good condition. If any problems are
apparent, do not tow the trailer. Check that the vehicle sits horizontally with the
trailer attached. If the vehicle is tipped sharply up at
the front and down at the rear, check the total trailer
weight, GVW, GAWs and tongue load again, then
confirm that the load and its distribution are accept-able. Check that the tire pressures are correct.
Check that the vehicle and trailer are connected
properly. Confirm that
–the trailer tongue is connected properly to the
hitch ball.– the trailer lights connector is connected prop-
erly and trailer ’s brake lights illuminate when the
vehicle’ s brake pedal is pressed, and that the trail-
er’ s turn signal lights flash when the vehicle ’s turn
signal lever is operated.– the safety chains are connected properly. –
all cargo in the trailer is secured safety in posi-
tion.– the side mirrors provide a good rearward field of
view without a significant blind spot.
Sufficient time should be taken to learn the “feel”
of the vehicle/trailer combination before starting out
on a trip. In an area free of traffic, practice turning, stopping and backing up.
Driving with a trailer
You should allow for considerably more stopping
distance when towing a trailer. Avoid sudden brak-
ing because it may result in skidding or jackknifing
and loss of control. Avoid abrupt starts and sudden accelerations. If
your vehicle has a manual transmission, always start
out in first gear and release the clutch at moderate
engine revolution. Avoid uneven steering, sharp turns and rapid lane
changes. Slow down before turning. Make a longer than
normal turning radius because the trailer wheels will
be closer than the vehicle wheels to the inside of the
turn. In a tight turn, the trailer could hit your vehicle. Crosswinds will adversely affect the handling of
your vehicle and trailer, causing sway. Crosswindscan be due to weather conditions or the passing of

Maintenance and service
11-36
have the vehicle checked at your SUBARU
dealer.Never use different brands of clutch fluid to-
gether. When clutch fluid is added, be careful not to
allow any dirt into the tank.
Recommended clutch fluid
FMVSS No. 116, fresh DOT 3 or 4 brake fluidBrake booster If the brake booster does not operate as described
below, have it checked by your SUBARU dealer.
1. With the engine off, depress the brake pedal sev-
eral times, applying the same pedal force each time.
The distance the pedal travels should not vary.
2. With the brake pedal depressed, start the en-
gine. The pedal should move slightly down to the
floor.
3. With the brake pedal depressed, stop the engine
and keep the pedal depressed for 30 seconds. The pedal height should not change.
4. Start the engine again and run for about one min-
ute then turn it off. Depress the brake pedal several
times to check the brake booster. Brake booster op-
erates properly if the pedal stroke decreases with
each depression.

Maintenance and service
11-47
– CONTINUED –
After driving approximately 600 miles (1,000 km),
check the wheel nuts again and retighten any nutthat has become loose. Tire replacement
The wheels and tires are important and integral
parts of your vehicle ’s design; they cannot be
changed arbitrarily. The tires fitted as standard
equipment are optimally matched to the characteris-
tics of the vehicle and were selected to give the best
possible combination of running performance, ride
comfort, and service life. It is essential for every tireto have a size and construction matching those
shown on the tire placard and to have a speed sym-
bol and load index matching those shown on the tire
placard.
Using tires of a non-specified size detracts from
controllability, ride comfort, braking performance,
speedometer accuracy and odometer accuracy. It
also creates incorrect body-to-tire clearances and
inappropriately changes the vehicle ’s ground clear-
ance.
All four tires must be the same in terms of manufac-
turer, brand (tread pattern), construction, and size.
You are advised to replace the tires with new ones
that are identical to those fitted as standard equip- ment.
For safe vehicle operation, SUBARU recommends
replacing all four tires at the same time. NOTE
Unidirectional tires: Some tires have a specified direction of rotation. A tire of this type has an ar-
row or other mark on its side wall to indicate thedirection of rotation. Install it so that the direc-tion of rotation is correct when the vehicle isdriven forward.