2003 SUBARU IMPREZA hood release

18
Instrument panel
1) Door locks (page 2-3)
2) Light control lever (page 3-16)
3) Combination meter (page 3-6)
4) Wiper control lever (page 3-21)
5) Hazard warning flasher switch
(page 3-6)
6) Audio (page 5-1)
7) Gear shift lever (MT) (page
7-11)/Selector lever (AT) (page7-14)
8) Outside mirror switch (page 3-29)
9) Climate control (page 4-1)
10) Cruise control (page 7-28)
11) Horn (page 3-32)
12) SRS airbag (page 1-42)
13) Tilt steering (page 3-31)
14) Fuse box (page 11-56)
15) Hood lock release (page 11-5)
16) Power window (page 2-22)

In case of emergency
9-17
– CONTINUED –
(1) Connect one jumper cable to the positive (+)
terminal on the discharged battery.
(2) Connect the other end of the jumper cable to
the positive (+) terminal of the booster battery.
(3) Connect one end of the other cable to thenegative (–) terminal of the booster battery.
(4) Connect the other end of the cable to the en-gine lifting bracket.
Make sure that the cables are not near any mov-
ing parts and that the cable clamps are not in
contact with any other metal.
5. Start the engine of the vehicle with the booster
battery and run it at moderate speed. Then start the
engine of the vehicle that has the discharged bat-
tery.
6. When finished, carefully disconnect the cables in
exactly the reverse order. Engine overheating
WARNING
Never attempt to remove the radiator cap until the engine has been shut off and has fullycooled down. When the engine is hot, thecoolant is under pressure. Removing the cap
while the engine is still hot could release aspray of boiling hot coolant, which could burn
you very seriously.
If the engine overheats, safely pull off the road and stop the vehicle in a safe place. If steam is coming from the engine compartment
Turn the engine off and get everyone away from the
vehicle until it cools down. If no steam is coming from the engine compartment
1. Keep the engine running at idling speed.
2. Open the hood to ventilate the engine compart-ment.

Maintenance and service
11-5
– CONTINUED –
suddenly even when the engine is stopped. When you do checking or servicing in the engine compartment whilethe engine is running
A running engine can be dangerous. Keep your fingers, hands, clothing, hair and toolsaway from the cooling fan, belts and any other
moving engine parts. Removing rings,watches and ties is advisable. Engine hood
To open the hood:
1. Pull the hood release knob under the instrument panel.

Maintenance and service
11-6
2. Release the secondary hood release located
under the front grille by moving the lever toward theleft.Lift up the hood, release the hood prop from its
retainer and put the end of the hood prop into theslot in the hood.
To close the hood: All models except WRX:
1. Lift the hood slightly and remove the hood prop
from the slot in the hood and return the prop to its
retainer.
2. Lower the hood until it approaches about 6 in.
(15 cm) from the closed position and let it drop.

Maintenance and service
11-7
– CONTINUED –
WRX:
1. Lift the hood slightly and remove the hood prop
from the slot in the hood and return the prop to its
retainer.
2. Lower the hood until it approaches about 12 in.
(30 cm) from the closed position and let it drop.
After closing the hood, be sure the hood is securelylocked.
If this does not close the hood, release it from a
slightly higher position. Do not push the hood forci-
bly to close it. It could deform the metal.
WARNING
Always check that the hood is properly locked before you start driving. If it is not, it might fly open while the vehicle is moving and block
your view, which may cause an accident and
serious bodily injury.