2003 SUBARU FORESTER air condition

3-9
Instruments and controls
–CONTINUED –
Ambient temperature gauge
The ambient temperature gauge shows the ambient
temperature in a range from –22 °Fto122 °F(–30 °Cto
50 °C).
The gauge can give a false reading under any of the
following conditions: When there is too much sun.
During idling; while running at low speeds in a traffic
jam; when the engine is restarted immediately follow-
ing a shutdown. When the actual ambient temperature falls outside
the specified indicator range.Warning and indicator lights
Several of the warning and indicator lights come on
momentarily and then go out when the ignition switch
is initially turned to the “ON” position. This permits
checking the operation of the bulbs.
Apply the parking brake and turn the ignition switch to
the “ON” position. The following lights come on:
Seatbelt warning light
SRS airbag system warning light
CHECK ENGINE warning light/Malfunction indica-
tor lamp
Charge warning light
Oil pressure warning light
AT OIL temperature warning light (AT vehicles)
ABS warning light
Brake system warning light
If any lights fail to come on, it indicates a burned-out
bulb or a malfunction of the corresponding system.
Consult your authorized SUBARU dealer for repair. Seatbelt warning light and chime
When the ignition switch is turned to the “ON” position,
the seatbelt warning light will come on and the remind-
er chime will sound for about six seconds to remind the
HS3047BA

3-30
Instruments and controls
will illuminate.
By pressing and releasing the right button, the com-
pass display is toggled on or off. When the compass is
on, an illuminated compass reading will appear in the
lower part of the mirror.
Even with the mirror in anti-glare mode, the mirror sur-
face turns bright if the transmission is shifted into re-
verse. This is to ensure good rearward visibility during reversing. Photosensors
The mirror has a photosensor attached on both the
front and back sides. If the glare from the headlights of
vehicles behind you strikes the mirror, these sensors detect it and make the reflection surface of the mirror
dimmer to help prevent you from being blinded. For
this reason, use care not to cover the sensors with
stickers, or other similar items. Periodically wipe the
sensors clean using a piece of dry soft cotton cloth or
an applicator.
Compass calibration
1. For optimum calibration, switch off all nonessential
electrical accessories (rear window defogger, heater/
air conditioning system, spotlight, etc.) and ensure all
doors are shut.
2. Drive to an open, level area away from large metal-
lic objects or structures and make certain the ignition
switch is in the “ON” position.
3. Press and hold the left button for 3 seconds then re-
lease, and the compass will enter the calibration
mode. “CAL” and direction will be displayed.
4. Drive slowly in a circle until “CAL” disappears from
the display (about two or three circles).
5. The compass is now calibrated. Further calibration
is not required. The compass will automatically cali-
brate from this point forward.
HS3038BA

4-1
4
Climate control
Ventilator ...................................................... 4-2 Air flow selection ............................................ 4-2
Center and side ventilators ............................ 4-3
Manual climate control system ................... 4-4 Control panel ................................................... 4-4
Heater operation ............................................. 4-6
Air conditioner operation (if equipped) ........ 4-9
Automatic climate control system
(if equipped) ................................................. 4-10 Temperature sensors ..................................... 4-15
Operating tips for heater and air
conditioner ................................................... 4-16 Cleaning ventilation grille .............................. 4-16
Efficient cooling after parking in direct
sunlight ............................................................ 4-17
Lubrication oil circulation in the refrigerant
circuit ............................................................... 4-17
Checking air conditioning system before
summer season .............................................. 4-17
Cooling and dehumidifying in high humidity
and low temperature weather conditions ..... 4-17
Air conditioner compressor shut-off when
engine is heavily loaded ................................ 4-17
Refrigerant for your climate control system 4-17
Air filtration system (if equipped) ............... 4-18 Replacing an air filter ..................................... 4-18

4-4
Climate control
Manual climate control system
Control panel
1) Temperature control dial
2) Fan speed control dial
3) Air flow control dial
4) Rear window defogger button (Refer to the “Rear win- dow defogger switch” in chapter 3.)
5) Air conditioner button (if equipped)
6) Air inlet selection button
Temperature control dial
This dial regulates the temperature of air flow from the
air outlets over a range from the blue side (cool) to red side (warm).
Fan speed control dial
The fan operates only when the ignition switch is
turned to the “ON” position. The fan speed control dial
is used to select four fan speeds. Air flow control dial
This dial has the following five positions:
: Air flows through the instrument panel outlets.
: Air flows through the instrument panel outlets and
the foot outlets.
: Air flows through the foot outlets and some
through the windshield defroster outlets.
: Air flows through the windshield defroster outlets
and foot outlets.
: Air flows through the windshield defroster outlets.
NOTE
Whenthedialisplacedinthe“ ”or
“ ”position, the air conditioner compressor
operates automatically regardless of the position
of the air conditioner button to defog the wind-
shield quickly. However the indicator on the air
HS4011BB
1
23
4
5
6

4-5
Climate control
– CONTINUED –
conditioner button will not come on. At the same
time, the air inlet selection is automatically set to
“outside air” mode.
In this state, you cannot select “recirculation”
mode by manually pressing the air inlet selection button.
Also, you cannot stop the air conditioner com-
pressor by pressing the air conditioner button. Air conditioner button (if equipped)
The air conditioner operates only when the engine is
running.
Push the air conditioner button while the fan is in op-
eration to turn on the air conditioner. The indicator light will come on.
Push it again to turn off the air conditioner.
Air inlet selection button
ON position (Recirculation): Interior air is recirculat-
ed inside the vehicle. Push the air inlet selection but-
ton to the ON position. The indicator light will come on.
OFF position (Outside air): Outside air is drawn into
the passenger compartment. Push the air inlet selec-
tion button again to the OFF position. The indicator
light will go off.
HS4012BA
HS4012CA

4-6
Climate control
Continued operation with the air inlet selection
button in the ON position may fog up the win-
dows. Switch to the OFF position as soon as
the outside dusty condition clears.
Heater operation
Defrosting or defogging the windshield
To direct warm air to the windshield and front door win-
dows: 1. Set the air flow control dial to the “ ” position.
2. Turn the temperature control dial all the way to the
right.
3. Set the fan speed control dial to the highest speed.
If your vehicle is equipped with an air conditioner,
when the “ ” or “ ” position is selected, the air
conditioner compressor automatically operates re-
gardless of the position of the air conditioner button to
defog the windshield quickly.
However, the air conditioner indicator light does not
come on at this time.
NOTE
Warm air also comes out from the right and left air
outlets. To stop warm air flow from these outlets,
turn the corresponding
thumb-wheel down.
HS4013AA

4-7
Climate control
– CONTINUED –
Heating and defrosting
To direct warm air toward the floor and the windshield:
1. Set the air flow control dial to the “ ”position.
2. Set the temperature control dial to the most com-
fortable level.
3. Set the fan speed control dial to the desired speed.
If your vehicle is equipped with an air conditioner,
when the “ ” or “ ” position is selected, the air
conditioner compressor automatically operates re-
gardless of the position of the air conditioner button to
defog the windshield quickly.
However, the air conditioner indicator light does not
come on at this time.NOTE
Warm air also comes out from the right and left air
outlets. To stop warm air flow from these outlets,
turn the corresponding thumb-wheel down. Heating
To direct warm air toward the floor:
1. Set the air inlet selection button to the OFF position
2. Set the air flow control dial to the “ ” position.
3. Set the temperature control dial to the most com-
fortable level.
4. Set the fan speed control dial to the desired speed.
HS4014AA
HS4015AA

4-9
Climate control
– CONTINUED –
4. Set the fan speed control dial to the desired speed.
When driving on a dusty road, set the air inlet selection
button to the “ON” position.
Continued operation with the air inlet selection
button in the ON position may fog up the win-
dows. Switch to the OFF position as soon as
the outside dusty condition clears.
Air conditioner operation (if equipped)
Cooling or dehumidifying
1) ON position
For cooling and dehumidification of the passenger
compartment, air flows through the instrument panel
outlets:
1. Set the air inlet selection button to the OFF posi-
tion.
2. Set the air flow control dial to the “ ” position.
3. Set the air conditioner button to the “ON” position.
4. Set the temperature control dial to the blue side.
5. Set the fan speed control dial at the highest speed.
HS4018BB
1