2003 SSANGYONG MUSSO oil

M162 ENGINE MECHANICAL 1B1-43
Components
1 Center Bolt (M18 x 50)
2 Center Bolt Washer
3 Vibration Damper and Pulley Assembly
4 Key
5 Crankshaft Front Seal
6 Timing Gear Case Cover
7 Crankshaft Sprocket (Camshaft Driven)
8 Crankshaft Sprocket (Oil pump Driven)
9 Crankshaft
10 Oil Pan 11 Oil Pan Gasket
12 Oil Pan Mounting Bolt (M6 x 22)
Service Data Standard
Permissble Deviation of The Vibration Damper Radial Runout
Axial Runout0.6 mm 0.6 mm
Tools Required
103 589 00 33 00 Puller
001 589 65 09 00 Socket Wrench Insert
602 589 00 40 00 Engine Lock Removal & Installation Procedure
1. Adjust the piston of number 1 cylinder to the TDC.

M162 ENGINE MECHANICAL 1B1-45
CRANKSHAFT FRONT RADIAL SEAL Preceding Work : Removal of belt pulley and vibration damper
1 Center Bolt (M18 x 50)................................ 1st step 200-220 Nm
2nd step 90 ° +10 °
2 Center Bolt Washer
3 Sleeve (Special Tool)
4 Crankshaft Front Seal
5 Key
Tools Required
601 589 03 14 00 Sleeve Replacement Procedure
1. Remove the radial seal with a screw driver.
Notice Use a clean cloth not to damage the radial seal mounting hole and the crankshaft.
5. Remove the sleeve and install the belt pulley and thevibration damper.
6. Check for leaks while operating the engine.
2. Coat the radial sealing lip with engine oil.
3. Using the sleeve, assemble the radial seal .
4. Align the sleeve groove and the woodruff key and tighten
the center bolt until the center bolt and the damper disk stop in the movement. Installation Notice
Tightening Torque 1st step 200 - 220Nm
2nd step 90
° + 10 °

1B1-46 M162 ENGINE MECHANICAL CRANKSHAFT REAR RADIAL SEAL Preceding Work : Removal of flywheel or drive plate
1 Special Tool
2 Special Tool3 Crankshaft Rear Seal
Tools Required
601 589 03 43 00 Sleeve Replacement Proceudre
1. Remove the radial seal with a screw driver.
Notice Use a clean cloth not to damage the radial seal mounting hole and the crankshaft.
2. Install the special tool (2) to the crankshaft.
3. Apply the engine oil on the special tool (2).
NoticeDo not use the grease.
4. Install the radial seal on the inner parts assembler.
5. Press in the special tool (1) until the radial seal is stopped.
6. Check for leaks while operating the engine.

M162 ENGINE MECHANICAL 1B1-47
CRANKSHAFT Preceding Work : Removal of engine assemblyRemoval of timing gear case cover Removal of cylinder head Removal of oil pumpRemoval of oil shield
1 12-sided Stretch Bolt ........ 55 Nm x 90°, Iubricate
2 Crank Shaft Bearing Cap
3 Crank Shaft Low Main Bearing
4 Lower Thrust Bearing
5 Crank Shaft

1B1-48 M162 ENGINE MECHANICAL Arrangement of the Thrust Bearing and the Main Bearing
1 - 12 Weight Balance/Color Marking Point
j1 - j7 Journal Main Bearing #1 - #7 Color Dot Marking
The color dot marking are put on the 1 , 2 , 4 , 6 , 8
, 10 ,12 and it indicates the diameter of crankshaft journal
by color as below. A Crankcase Side
B Bearing Cap Side (Oil Pan Side)
C Axial Fit Bearing (Number 5 Bearing Point)
D Radial Bearing
1 Upper Main Bearing
2 Upper Thrust Bearing
3 Crankshaft
4 Lower Main Bearing
5 Lower Thrust Bearing

M162 ENGINE MECHANICAL 1B1-49
Selection of Crankshaft Main Bearing
1. Crankcase SideThere are seven punching marks on the mating surface to oil pan. This mark is correspondent to the bearing
distinguished by color. Select the relevant bearing according to the punching mark when repaired.
2. Crankshaft Bearing Cap Side Select the crankshaft main bearing according to the markingletter on the crankshaft main journal when repaired.
Color Dot Marking
Blue
Yellow
Red
White VioletCrankshaft Journal Diameter (mm)
57.960 - 57.965 57.955 - 57.960 57.950 - 57.95557.945 - 57.95057.940 - 57.945
Punching Mark


Bearing Color Selected
Blue
Yellow
Red
Marking Letter
B Y
R
W VBearing Color Selected
Blue
Yellow
Red
White Violet
Service Data Unit : mm
Crankshaft
Bearing Jour- nal Diameter Crankshaft
Bearing
Diameter Crankshaft
Journal Width at fit bearing Connecting Rod
Bearing Journal Diameter Connecting
Rod Bearing
Jourmal Width
Standard size
1st repair size
2nd repair size 3rd repair size4th repair size 57.950-57.965 57.700-57.71557.450-57.46557.200-57.215
56.950-56.965 58 24.50-24.533
-47.94-47.96
47.7547.5047.25 47.00 27.958-28.042
-
Crankshaft Standard
and Repair Size

1B1-50 M162 ENGINE MECHANICALInstallation Notice
Make sure the crankshaft bearing cap properly seated in place in the crankcase side. When perfectly installed,the projected part (arrow) locates in the left side (intakemanifold side).
Assemble so that the projected part of the cap andcrankcase face the same direction.
Removal & Installation Procedure
1. Unscrew the connecting rod bearing cap bolt and remove
the bearing cap. Installation Notice
2. Unscrew the crankshaft bearing cap bolts and separate the upper and lower bearing shells and thrust washers. Installation Notice
Remove the bearing cap from front (pulley side) to rear.
Make sure that the upper and lower bearing shells do not change each other and coat with engine oil.
The oil grooves (arrows) in the thrust washers must faceoutward and insert the thrust bearing into the bearingcap.
There are five kinds of thrust washers by thickness. Selectthe proper washer when repaired.
3. Remove the crankshaft.
4. Installation should follow the removal procedure in the reverse order.
5. After completion of the installation, check for the rotating condition of the crankshaft.
Make sure that the upper and lower bearing shells do
not change each other.
Coat the bearing shell with engine oil.
Install the bearing cap according to the consecutive
number.
Part No. : 601 030 00 622.15 mm
Part No. : 601 030 01 62 2.20 mm
Part No. : 601 030 02 62 2.25 mm
Part No. : 601 030 03 62 2.30 mm
Part No. : 601 030 04 62 2.40 mm
Tightening Torque 40 Nm + 90 °
Tightening Torque 55 Nm + 90°

1B1-54 M162 ENGINE MECHANICAL Removal & Installation Procedure
1. Unscrew the stretch bolt.Installation Notice
Sectional View
1 Oil Pan
2 Cover
3 Crankshaft Front Seal
4 Flywheel MTG Bolt
5 Crankshaft
6 Dowel Pin
7 Plate
8 TGCC
9 Bolt
10 Front Drive Plate
11 Rear Drive Plate
12 Rivet
13 Segment
14 Ring Gear

Replace the bolt when the stretch side diameter (d) of the flywheel mounting bolt is less than 8.0mm.
For the stretch bolt tightening, keep the socket wrench
and Tommy-bar to be 90 ° and tighten as specified.
2. Remove the flywheel for manual transmission vehicles, or the driven plate (3), and plate (2) for Auto. transmission vehicle.
3. Installation should follow the removal procedure in the reverse order. Tightening Torque
1st step 45+5 Nm
2nd step 90
° + 10 °