2003 SSANGYONG MUSSO steering

2C-8 FRONT SUSPENSION FRONT LOWER AND UPPER ARM1 Nut ................................................... 120-140 Nm
2 Fulcrum Pin and Upper Arm Assembly
3 Camber/Caster Adjusting Shim
4 Bolt
5 Bolt
6 Washer
7 Upper Arm End
8 Nut ....................................................... 16-22 Nm
9 Castle Nut .......................................... 80-150 Nm
10 Cotter Pin ............................................... Replace
11 Nut ................................................... 150-180 Nm
12 Washer
13 Bolt
14 Lower Arm Assembly and Lower Arm End
15 Bolt
16 Washer
17 Nut ....................................................... 60-80 Nm
Preceding Work : Removal of the torsion bar spring
Removal of the steering knuckle and drive shaft

2E-6 TIRES AND WHEELS
4. Tire pressure inspection. Tire pressure.
Check tread contact with road.
Notice
If underinflated, tire may come away from the wheel
during rapid steering.
An overinflated tire will cause a hard riding and uneven
wear.
Front & Rear
(P235/75R15) 2.1kg/cm (30PSI)
2
5. Wheel balance. Balance weights should be on each side. When the wheel
is out of balance or a tire has been repaired, be sure to balance the wheel again.
If total weight is over 150g, readjust the balance by
reinstalling the tire on the wheel.
Balance weight should not protrude from the wheel rim
over 3mm.
For aluminum wheel, use aluminum wheel balance weight
only.

M/T M/TA/T (MB)M/TA/T (BTRA) M/T A/T (BTRA)M/TA/T (MB)M/T A/T (MB) A/T (BTRA)M/TA/T (MB)A/T (BTRA)
SECTION 3A
FRONT DRIVE AXLE
TABLE OF CONTENTSSPECIFICATIONS
GENERAL SPECIFICATIONS
Specifications . . . . . . . . . . . . . . . . . . . . . . . .
3A-1
General Specifications . . . . . . . . . . . . . . . . . . 3A-1
Fastener Tightening Specifications . . . . . . . . . 3A-2
Component Locator . . . . . . . . . . . . . . . . . . . 3A-3
Front Axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3A-3
Auto-Locking Hub . . . . . . . . . . . . . . . . . . . . . . 3A-4
Vacuum Circuit . . . . . . . . . . . . . . . . . . . . . . . . 3A-5Maintenance and Repair . . . . . . . . . . . . . . .
3A-6
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 3A-6
Vacuum Line . . . . . . . . . . . . . . . . . . . . . . . . . . 3A-6
Steering Knuckle and Drive Shaft . . . . . . . . . . 3A-8
Front Axle . . . . . . . . . . . . . . . . . . . . . . . . . . . 3A-14
Unit Repair . . . . . . . . . . . . . . . . . . . . . . . . . 3A-16
Axle Housing . . . . . . . . . . . . . . . . . . . . . . . . . 3A-16
Application
Drive Shaft Type
Axle Housing Type
Differential TypeDifferential Gear
CV Joint
Build - up
Conventional
Hypoid Gear 4.56 4.56 3.734.565.384.27 4.89 4.894.554.554.55 5.86 3.733.734.89
1.4 L
SAE 80W/90, API GL - 5
Description
661NA 662NA 661LA662LA E20 E23 E32
Reduction Ratio Oil Capacity Oil Specification

3A-2 FRONT DRIVE AXLEFASTENER TIGHTENING SPECIFICATIONS
Steering Knuckle and Drive Shaft
Application
Drive Shaft to Front Axle Inner Shaft Wheel Speed Sensor Drive Shaft Cover Bolt
Locking Hub Washer ScrewHub Flange BoltHub Nut N
m
25 - 35
85 - 105 50 - 60 2 - 4
70 - 90
15

3A-8 FRONT DRIVE AXLE STEERING KNUCKLE AND DRIVE SHAFT1 Front Axle Inner Shaft
2 Front Axle Drive Shaft
3 Spring Washer
4 Bolt ...................................................... 45-60 Nm
5 Steering Knuckle

FRONT DRIVE AXLE 3A-9
Removal & Installation Procedure
1. Remove the tire.Installation Notice
Steel Wheel
Aluminum Wheel
Tightening Torque80 - 120 Nm
110 - 130 Nm
2. Remove the autolocking hub vacuum hose.
3. With ABS Remove the wheel speed sensor from the steering knuckle. Installation Notice
4. Remove the mounting bolts and pull off the caliper assembly. Installation Notice
Tightening Torque 6 - 8 Nm
Hose Bolt
Mounting Bolt
Tightening Torque25 - 35 Nm
85 - 105 Nm
Notice Be careful not to damage the brake hose.

3A-12 FRONT DRIVE AXLE
10. Remove the cotter pin and slotted nut and then removethe steering knuckle arm and tie-rod.
Installation Notice Replace the cotter pin with new one.
Tightening Torque 35 - 45 Nm
11. Remove the cotter pin and nut from the steering knuckle arm and upper arm ball joint connection.
Installation Notice
Tightening Torque 80 - 150 Nm
Replace the cotter pin with new one.
12. Remove the cotter pin and nut from the steering knuckle arm and lower and lower arm boll joint connection.
13. Carefully remove the knuckle arm. Installation Notice
Tightening Torque 120 - 180 Nm

3A-14 FRONT DRIVE AXLE
1 Axle Mounting Bracket
2 Breather Hose
3 Bolt (Rear)
4 Nut .....................................................95-142 Nm
5 Cross Member
6 Bolt (Front)
7 Bushing
8 Spacer
FRONT AXLE9 Bushing
10 Nut ..................................................... 95-142 Nm
11 Front Axle Assembly
12 Nut ....................................................... 70-80 Nm
13 Bolt
14 Inner Axle Shaft (LH)
15 Inner Axle Shaft (RH)
Preceding Work : Removal of the front axle drive shaft
Removla of the steering gear box