2003 SSANGYONG MUSSO drain bolt

1B3-64 OM600 ENGINE MECHANICAL
8. Remove the guide pulley bracket (24).
Tools Required
116 589 03 07 00 Socket Wrench Removal Procedure
1. Remove the fan clutch and cooling fan belt pulley.
2. Drain the engine oil completely.
3. Remove the oil dipstick tube bracket bolts.
4. Remove the crankshaft pulley.
5. Loosen the bolt (1) and then remove the cylinder head cover(2) and gasket.
6. Remove the vacuum pump.
7. Detach the closing cover (20). Remove the bolts(21) and then remove the guide pulley (22).

OM600 ENGINE MECHANICAL 1B3-171
OIL PAN1 Gasket ................................................... Replace
2 Upper Oil Pan
3 Combination Bolt ...................................... 10 Nm
4 Combination Bolt ...................................... 10 Nm
5 Gasket ................................................... Replace 6 Lower Oil Pan
7 Combination Bolt
...................................... 25 Nm
8 Drain Plug ................................................. 25 Nm
9 Washer Seal .......................................... Replace
10 Oil Pan
*Remove and install as numerical sequence. Notice Replace the washer seal with new one.
OM662LA OM661LA

1D1-2 M162 ENGINE COOLINGFASTENER TIGHTENING SPECIFICATIONS
N

 m
30
22.5 - 27.5
9 - 11
9 - 11
9 - 11
40.5 - 49.5
3 - 73 - 7
Application
Coolant Drain PlugEngine Hanger Bracket and Coolant OutletPort Bolt Thermostat Cover Bracket Bolt Oil Cooler Pipe Line BoltCooling Fan BoltViscous Clutch Bolt
Automatic Transmission Oil Cooling Hose Bolt Cooling Fan Shroud Bolt

M162 ENGINE COOLING 1D1-5
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
COOLANT DRAIN AND FILL UP Draning & Filling up Procedure 1. Loosen the cap a little and release pressure and remove the cap. NoticeFor the risk of scalding, the cap must not be opened unless the coolant temperature is below 90 o
C.
2. Loosen the radiator lower drain cock and drain the coolant.
Notice Collect coolant by using a proper container.
3. Drain the coolant from the crankcase by inserting a hose(dia. 14mm) onto the drain bolt on the side of crankcase (exhaust manifold) and by loosening the plug. Notice
Just loosen the drain plug to drain the coolant and do not remove the plug completely.
Collect coolant by using proper container.
4. After complete draining of the coolant, remove the hose connector to drain plug and reinstall the drain plug. Installation Notice
5. Tighten the radiator lower drain cock.
Tightening Torque 30 Nm

M162 ENGINE COOLING 1D1-7
COOLANT CONNECTION FITTING Preceding Work : Removal of cooling fan shroud
1 Bolt (M8 X 100, 2 pieces) ...............22.5-27.5 Nm
2 Engine Hanger Bracket
3 Coolant Outlet Port
Removal & Installation Procedure
1. Drain coolant from the radiator.
2. Remove the hose mounting clamp (5) and disconnect the coolant hose (6).
3. Remove the two bolts (1), the engine hanger bracket (2) and coolant outlet port (3).Installation Notice 4 O-ring
5 Hose Mounting Clamp
6 Hose
Replace the O-ring with new one.
4. Installation should follow the removal procedure in the reverse order.
5. Fill up the coolant as specified.
6. Check the leaks in the cooling system.
Tightening Torque 22.5 - 27.5 Nm

M162 ENGINE COOLING 1D1-9
Removal & Installation Procedure
1. Drain the coolant.
2. Disconnect the coolant pump wire connector.
3. Loosen the hose clip and dsconnect all hoses from thecoolant pump
4. Remove the coolant line bolts (4) and then remove the
coolant line (2).Installation Notice Notice Replace the seal (3).
5. Remove the mounting bolts (11) and carefully pull out coolant pump (10).Installation Notice
Tightening Torque 9 - 11 Nm
Notice Replace the seal (13).
Tightening Torque 21 Nm
6. Installation should follow the removal procedure in the reverse order.
7. Fill up coolant.
8. Do coolaing system leakage test

1D1-10 M162 ENGINE COOLING THERMOSTAT
Removal & Installation Procedure
1. Drain the coolant from the radiator.
2. Loosen the hose mounting clamp (6) and remove the heaterhose (7).
3. Unscrew the three bolts (5) and remove the thermostat cover bracket, thermostat cover and the thermostat in order. Installation Notice
1 Thermostat Cover
2 Thermostat
3 O-ring
4 Thermostat Cover Bracket
5 Bolt (M6 X 25, 3 pieces)
.........................9-11 Nm
6 Hose Mounting Clamp
7 Heater Hose
Do not separate the thermostat cover and thermostat.
4. Replace the O-ring if necessary.
5. Check the leakage in the cooling system.
Tightening Torque 9 - 11 Nm

M162 ENGINE COOLING 1D1-11
OIL COOLER PIPE LINE Preceding Work : Removal of upper intake manifold
Tightening Torque 9 - 11 Nm
1 Upper Intake Manifold
2 Bolt (M6 X 35, 1 piece)
...........................9-11 Nm
3 Bolt (M6 X 16, 2 pieces) .........................9-11 Nm4 Oil Cooler Pipe Line
5 O-ring .................................................... Replace
Removal & Installation Procedure
1. Drain the coolant.
2. Unscrew the bolts (2, 3) and remove the oil cooler pipe line (4). Replace the O-ring with new one. Installation Notice
3. Installation should follow the removal procedure in the reverse order.
4. Fill up the coolant as specified.
5. Check the leaks in the cooling system.