2003 SSANGYONG MUSSO tire pressure

DescriptionAlumimun7JJ X 15
Radial Tire
P215 / 75R 15 - 30psi P235 / 75R 15 - 30psiP255 / 70R 15 - 30psi
Application
Wheel SECTION 2E
TIRES AND WHEELS
TABLE OF CONTENTS
SPECIFICATIONS
GENERAL SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Application
Wheel Bolt
N
m
80 - 120
110 - 130
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 2E-1 General Specifications . . . . . . . . . . . . . . . . . . 2E-1
Fastener Tightening Specifications . . . . . . . . . 2E-1
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . 2E-2 Wear Pattern Diagnosis . . . . . . . . . . . . . . . . . 2E-2
Identification . . . . . . . . . . . . . . . . . . . . . . . . . 2E-3 Radial Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . 2E-3Wheel Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . 2E-3
Component Locator . . . . . . . . . . . . . . . . . . . 2E-4 Wheel and Tire . . . . . . . . . . . . . . . . . . . . . . . . 2E-4
Maintenance and Repair . . . . . . . . . . . . . . . 2E-5
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 2E-5 Wheels and Tires . . . . . . . . . . . . . . . . . . . . . . 2E-5
Material Size
Tire Type Size and Tire Pressure
Steel Alumimum

2E-6 TIRES AND WHEELS
4. Tire pressure inspection. Tire pressure.
Check tread contact with road.
Notice
If underinflated, tire may come away from the wheel
during rapid steering.
An overinflated tire will cause a hard riding and uneven
wear.
Front & Rear
(P235/75R15) 2.1kg/cm (30PSI)
2
5. Wheel balance. Balance weights should be on each side. When the wheel
is out of balance or a tire has been repaired, be sure to balance the wheel again.
If total weight is over 150g, readjust the balance by
reinstalling the tire on the wheel.
Balance weight should not protrude from the wheel rim
over 3mm.
For aluminum wheel, use aluminum wheel balance weight
only.

4A-2 HYDRAULIC BRAKESCheck
Dirty or Lack of Fluid Air in Brake SystemFaulty Brake Booster Poor Contact of Pad or Lining Oil or Grease on PadFaulty Auto AdjusterOver Heated Rotor Due to Dragging Pad or LiningClogging Brake Line
Faulty Proportioning Valve Check
Incorrect Tire Pressure Between Left and Right Poor Contact of Pad or LiningOil or Grease is Applied to Pad or LiningBent or Uneven Wear of DrumIncorrectly Mounted Wheel Cylinder Faulty Auto Adjuster Action
Repair
Retighten Replace Replace
RepairRepair
Lubricate
Retighten
Check
Incorrectly Mounted Back Plate or CaliperLoosened Bolt of Back Plate or CaliperCrack or Uneven Wear of Brake Drum or DiscPad or Lining Sticking to Contact Surface Excessive Clearance Between Caliper and Pad Uneven Contact of PadLack of LubricationLoosened Suspension DIGNOSIS
NOISE OR VEHICLE VIBRATION WHEN APPLIED BRAKE
PULLS TO ONE SIDE WHEN BRAKING
Action Adjust
Repair
Replace Replace
Repair
Replace
Action
Replenish or Replace(Check eventual leakage) Bleeding
Replace
Repair
Replace Replace RepairRepair
Repair
POOR BRAKING
( If low cut-in : Adjust ) ( If Leakage : Replace )

TRANSFER CASE (PART TIME 4408) 5D1-3
Cannot Front Wheel Drive when Shifted 4H,4LDIAGNOSIS
Electric Shift Problems
Action
Overhaul and check, replace if necessary. Overhaul and check for wear and damage.
Replace if necessary.
Check sliding parts, replace if necessary.
Checks
Faulty or Damaged TCCU, Speed Sensor, Motor, Clutch or Internal Wirings Damaged or Worn Shift Cam, Hub, Fork and Rail Shift Binding Shift Fork, Hub Collar or Gear
Checks
Broken Drive Chain Action
Check sliding parts, replace if necessary.
Noise in 4WD Operation
Checks
Improper or low oil Loosened bolts or mounted partsNoisy T/C bearing Noisy gears Action
Drain and replace with specified oil. Retighten as specified.Disassemble bearings and parts and check for wear or
damage. Replace if necessary. Check for wear and damage including speedometer
gear, replace if necessary.
Noise in 4H or 4L
Checks
Worn or Damaged Sprockets or Drive Chain
Incorrect Tire Pressure Action
Disassemble and check for wear and damage, replace
if necessary. Adjust tire pressure.
Transfer Case Oil Leakage
Action
Replace the case. Clean case and parts and check for leakage.
Remove breather hose and clean, replace if necessary.Use specified oil and adjust oil level.Retighten Use specified sealant and retighten. Replace
Checks
Cracked Transfer CaseLeakage from Other PartsBreather CloggingImproper or too much OilLoosened Sealing Bolts Improperly Applied Sealant Worn or Damaged Oil Seal

9B-10 LIGHTING SYSTEM Head Lamp Focusing When using the beam setting device
1. The head lamp focus should be adjusted by using a properbeam setting device.
2. Adjust the head lamp focus by using Up/Down, Left/Right adjusting screws.
When using the screen
1. Put the vehicle on the leveling surface.
2. One person is needed to seat on the driver's seat without other loads(CVW) and check the tire pressure if it is in the specification.
3. The distance between the headlamp and the screen is 25m.
4. Draw the vertical line (crossing the center of each headlamp) on the screen.
5. Start the engine.
6. Check if the cut-off line of the headlamp on the screen is in the specification.
1 ) Left/right direction
- The degree of the cross point at the cut-off line of theheadlamp and the vertical line should be 15.
2 ) Up/down direction - The distance between the cut-off line of the headlampand the horizontal line should be 25cm.
7. Adjust the focus if the cut-off line of the headlamp is out of
the specification by using up/down, left/right adjusting screws. A : Up/down direction adjusting screwB : Left/right direction adjusting secrw