2003 SSANGYONG MUSSO key

1B2-52 M161 ENGINE MECHANICAL CRANKSHAFT FRONT RADIAL SEAL Preceding Work : Removal of belt pulley and vibration damper
1 Center Bolt (M18 x 50)............................... 1st step 200-220 Nm
2nd step 90° +10 °
2 Center Bolt Washer
3 Sleeve (Special Tool)
4 Crankshaft Front Seal
5 Key
Tools Required
601 589 03 14 00 Sleeve Replacement Procedure
1. Remove the radial seal with a screw driver.
Notice Use a clean cloth not to damage the radial seal mounting hole and the crankshaft.
5. Remove the sleeve and install the belt pulley and thevibration damper.
6. Check for leaks while operating the engine.
2. Coat the radial sealing lip with engine oil.
3. Using the sleeve, assemble the radial seal .
4. Align the sleeve groove and the woodruff key and tighten
the center bolt until the center bolt and the damper disk stop in the movement. Installation Notice
Tightening Torque 1st step 200 - 220Nm
2nd step 90
° + 10 °

1B2-88 M161 ENGINE MECHANICAL
CRANKSHAFT SPROCKET Preceding Work : Removal of oil panRemoval of tensioning rail Removal of crank case guide rail Removal of cylinder head
6 Bolt (M8 x 20, 1 piece) / Washer ..........29-35 Nm
7 Oil Pump Sprocket
8 Oil Pump
9 Oil Pump Roller Chain
10 Timing Chain
1 Oil Pump Chain Tensioner
2 Oil Pump Chain Spring
3 Oil Pump Chain Bushing (Pin)
4 Crankshaft Sprocket
5 Key

M161 ENGINE MECHANICAL 1B2-89
Tools Required
615 589 01 33 00 Caulking Bolt Removal & Installation Procedure
1. Put the assembly mark at the crankshaft sprocket (4) andthe timing chain (10) with the paint (arrow). Installation Notice Align the assembly marks on cranshaft sprocket and timing chain. Also, align the assembly marks on camshaft sprocketand timing chain when installing.
2. Unscrew the bolt (6) and remove the oil pump sprocket (7) from the oil pump. Installation Notice
Caulking (04) 615 589 01 33 00
3. Remove the oil pump roller chain (9).
4. Remove the oil pump chain tensioner (1), oil pump chain
bushing (3), and the oil pump chain spring (2).
5. Remove the crankshaft sprocket (4) using the puller (04, special tool). Notice
Make sure not to lose the crankshaft pulley key (5) when
removing.
Install the crankshaft sprocket (4) after warming it up.
6. Installation should follow the removal procedure in the reverse order.
Tightening Torque 29 - 35 Nm

OM600 ENGINE MECHANICAL 1B3-65
11. Remove the alternator bracket (16).
9. Disconnect the pipes of power steering pump and removethe belt pulley. Notice
Be careful not to lose the key.
10. Remove the nut and pull out the bolt and then remove the power steering pump.
12. Remove the fuel filter.

OM600 ENGINE MECHANICAL 1B3-75
Sectional View
3 Socket Bolt
4 Crankshaft Belt Pulley
5 Vibration Damper
6 Bolt
7 Washer
8 Straight Pin
Notice The mounting position of vibration damper is fixed by straight pin (8).
Tools Required 602 589 00 40 00 Engine Lock103 589 00 30 00 Puller 9 Hub
11 Radial Seal
12 Timing Gear Case Cover
13 Key
14 Crankshaft Sprocket
16 Crankshaft

1B3-78 OM600 ENGINE MECHANICAL Installation Procedure
1. Install the hub.Notice Exactly align the woodruff key and the groove of hub (arrow).
2. Install the washer (7) and tighten the bolt (6).
Washer (new) : 1 EA 200 Nm + 90°
3. Install the vibration damper. Notice Exactly align and insert onto the straight pin.
4. Install the belt pulley.
Tightening Torque 25 Nm
Notice Align the alignment marks.

1B3-80 OM600 ENGINE MECHANICAL
CRANKSHAFT FRONT RADIAL SEAL
1 Radial Seal
2 Timing Case Cover
Tools Required 601 589 03 14 00 Sleeve3 Woodruff Key

OM600 ENGINE MECHANICAL 1B3-81
Notice The sealing lip of the repair radial seal is offset to the inside by 2mm to ensure that is does not run in any groove which the standard radial seal may have left on the crankshaft flange.A Standard Radial SealB Repair Radial Seal
Replacement Procedure
1. Pull out the radial seal (1) and be careful not to damage the sealing surface of timing case cover.
2. Thoroughly clean the mounting bore of the radial seal.
3. Coat a little oil on the sealing lip of new radial (1) and contact surface. Notice Don ’t use grease.
4. Install the radial seal (1) by using a sleeve (4).
NoticeAlign the groove of sleeve and woodruff key(arrow).
Sleeve 601 589 03 14