2003 SSANGYONG MUSSO heating

M162 ENGINE CONTROLS 1F1-37
Pin No.Abbreciation
Description
1 23456789
10 11
121314151617181920 -
TM.50 --
GND ---
LSH1
TM.31TM.87TM.30
WFS I/O WFS O -
GND LS1 ---
-Starter motor TM.50--Electronic ground---Lambda probe 1 heatingPower ground TM.31
V-BATTERY TM.87
V-BATTERY TM.30Immobilizer crypto readImmobilizer crypto write-Lambda probe 1 groundLambda probe 1 signal---
ECU Pin Numbers and Descriptions
Vehicle Connector

M162 ENGINE CONTROLS 1F1-41
Application
Pin No.Description
- Starter motor TM.50- - Electronic ground--- Lambda probe 1 heating Power ground TM.31
V-BATTERY TM.87
V-BATTERY TM.30Immobilizer crypto read Immobilizer crypto write -Lambda probe 1 groundLambda probe 1 signal- - -Brake switch-- - --Air conditioning clutch relay- - -1 23 4 5678 9
10 11
12 13 14 15161718 19 20212223 24 25262728 29 30-
TM.50 - -
GND - --
LSH1
TM.31TM.87TM.30
WFS I/O WFS O
-
GND LS1 - - -
BRS -- - --
KLIKU - - - -
--
-- -





-

- - -
-- - --
- - - -
- -
- --






-

- - -
-- - --
- - -
: Standard, : Option Remarks
Abbreviation E32 ENG,
5speed M/T
E32 ENG,
4speed A/T (BTRA)

1F1-72 M162 ENGINE CONTROLS
OXYGEN SENSOR
1 Electricity Wire
2 Oxygen Sensor Housing
3 Sensor Ceramic
4 Electrode (Internal)
5 Electrode (External)
6 Heating Coil
7 Open Space
8 Protector Tube
Functions The oxygen sensor optimizes the combustion (Air-Fuel Ratio 14.7:1) and resets the Air-fuel ratio in the ECU after sensingthe amount of oxygen from the exhaust gases to diminish the exhaust gases.
- Rich(<1) above approx. 450mV
- Lean(>1) below approx. 450mV
Locatoin of Sensor Oxygen sensor is located on the front exhaust pipe.

M162 ENGINE CONTROLS 1F1-73
Oxygen Sensor Signal Voltage Inspection
1. Measure the oxygen sensor signal voltage between the ECUterminal No.11 and No.9. Maintain the engine speed ia at idle while the coolant temperature is over 80 °C.
If the measured value is not within the specified value, thepossible cause may be in cable, oxygen sensor or ECU.
Oxygen Sensor Heating Voltage Inspection
1. Measure the oxygen sensor heating voltage between the ECU terminal No.11 and No.9. Maintain the engine speed ia at idle while the coolant temperature is over 80 °C.
If the measured value is not within the specified value, the possible cause may be in cable, oxygen sensor or ECU.
Oxygen Sensor Heating Current Consumption
Inspection
1. Measure the oxygen sensor heating current consumption between the ECU terminal No.9 and No.5 while the ignition switch is in "ON" position. If the measured value is not within the specified value, the possible cause may be in cable, oxygen sensor or ECU.
Specified Value 0.2 - 2.0 A
Specified Value -0.2 - 1.0 V
Specified Value 11 - 14

Type
Spring TypeCoil Spring Shock Absorber
Stabilizer TypeDescription
5-link
Coil Spring
13.8 mm
126.8 mm 384.5 mm
139.6 mm 2.58 kg
Cylindrical Reciprocation Type Torsion Bar Type
SECTION 2D
REAR SUSPENSION
TABLE OF CONTENTS
SPECIFICATIONS
GENERAL SPECIFICATIONS
Wire Diameter (mm) Diameter (mm)Free Heigth (mm)Outer Diameter (mm) Spring Constant (kg m)
Application
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 2D-1
General Specifications . . . . . . . . . . . . . . . . . . 2D-1
Fastener Tightening Specifications . . . . . . . . . 2D-1
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . 2D-2 Noise (During Straight Driving) . . . . . . . . . . . . 2D-2
Oil Leakage . . . . . . . . . . . . . . . . . . . . . . . . . . 2D-2
Noise (During Turning) . . . . . . . . . . . . . . . . . . 2D-2 Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2D-3
Component Locator . . . . . . . . . . . . . . . . . . . 2D-4
Maintenance and Repair . . . . . . . . . . . . . . . 2D-5
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 2D-5
Rear Suspension(5-Link) . . . . . . . . . . . . . . . . 2D-5
Rear Shock Absorber . . . . . . . . . . . . . . . . . . . 2D-9
FASTENER TIGHTENING SPECIFICATIONS
Application
Upper Nut Stabilizer Bar Bolt Lateral Rod Nut Shock Absorber Mounting Nut Upper Arm Fixing Nut
N
m
16 - 22 30 - 45
150 - 180 50 - 65
150 - 180

REAR SUSPENSION 2D-3
HEATING
Check
Lack of Oil Insufficient Backlash of GearsExcessive Preload of Bearing Action
Replenish Adjust Adjust

SECTION 3D
REAR DRIVE AXLE
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 3D-1 General Specifications . . . . . . . . . . . . . . . . . . 3D-1
Fastener Tightening Specifications . . . . . . . . . 3D-2
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . 3D-3 Noise (During Straight Driving) . . . . . . . . . . . . 3D-3
Oil Leakage . . . . . . . . . . . . . . . . . . . . . . . . . . 3D-3
Noise (During Turning) . . . . . . . . . . . . . . . . . . 3D-3
Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3D-3
Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3D-4 Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3D-4
Component Locator . . . . . . . . . . . . . . . . . . . 3D-5
Maintenance and Repair . . . . . . . . . . . . . . . 3D-6
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 3D-6
Axle Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3D-6
Axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3D-9
Unit Repair . . . . . . . . . . . . . . . . . . . . . . . . . 3D-11 Axle Housing . . . . . . . . . . . . . . . . . . . . . . . . . 3D-11
LSD (Limited Slip Diffrential) . . . . . . . . . . . . . 3D-16
SPECIFICATIONS
GENERAL SPECIFICATIONS
Axle Shaft Type
Axle Housing TypeDifferential Reduction Ratio
Type Gear M/T M/TA/T (MB)M/TA/T (BTRA) M/T A/T (BTRA)
Description
Semi - floating
Salibury (Build-up)
Conventional Type Hypoid Gear
4.55 4.55 3.73 4.555.384.274.89Application
661NA 662NA 661LA 662LA

REAR DRIVE AXLE 3D-3
Checks
Worn or Damaged Tooth of Pinion or Side Gear Worn Pinion Shaft Excessive Backlash of Pinion Gear and Side Gear Excessive End-play of Rear Axle ShaftIncorrect Contact of Side Gear and Differential CaseAxle Housing CrackBent or Poor Installation of Drive Pinion Oil Seal
Damaged or Torn Drive Pinion Oil Seal Loosened Bearing CollarWorn or Damaged Universal JointWorn or Damaged Axle Shaft Bearing Checks
Excessive OilFaulty Seal of Carrier Contact Surface Axle Housing Crack Worn or Damaged Oil Seal Checks
Lack of OilLow Viscosity of OilInsufficient Oil Excessive Backlash of Ring Gear
Worn or Damaged Tooth of Ring and Pinion GearWorn or Damaged Drive Pinion BearingBent Axle HousingBent Differential Case Worn Pinion Shaft Incorrect Drive Pinion PreloadIncorrect Contact of Ring Gear and Pinion DIAGNOSIS
NOISE (DURING STRAIGHT DRIVING)
Action
Replenish
Replace Replace
Adjust
ReplaceReplaceReplaceReplace Replace Adjust
Retightening
OIL LEAKAGE
Action Adjust
Repair
Replace Replace
NOISE (DURING TURNING)
Action
Replace Replace Replace Adjust
Replace ReplaceReplace Replace ReplaceReplaceReplace
HEATING
Checks
Lack of Oil Insufficient Backlash of GearsExcessive Preload of Bearing Action
Replenish AdjustAdjust