2003 SSANGYONG MUSSO oil

1B3-52 OM600 ENGINE MECHANICALLength(L)
Assembly Procedure
1. Replace the cylinder head gasket.
2. Install the cylinder head onto the crankcase.
Notice Align the cylinder head holes with the guide pins.
3. Measure the length(L) of cylinder head bolts. Notice If the max. length is exceeded, replace the bolts.
Thread Dia. Max. Limit(L)
M10 M10 M1080mm
102mm 115mm 82mm
104mm 117mm
when new
4. Coat the head contact surface of bolts and thread with oil
and insert them as shown. - Cylinder head bolts arrangement
Bore 1 ........................................... M10 ×
80
2 ........................................... M10 × 102
3 ........................................... M10 × 11 5
4 ........................................... M 8 × 50
5 ........................................... M 8 × 80 OM662LA

1B3-56 OM600 ENGINE MECHANICAL
17. Coat the camshaft with oil and install the camshaft on thecylinder head to be TDC mark(arrow) upward.
18. Measure the axial end play of the camshaft.
End Play 0.06 - 0.21mm
Notice If out of standard, adjust it with the proper thickness of
locking washer.
19. Install the bearing caps on the camshaft according to the number on the caps.
20. Tighten the bearing cap bolts according to the numerical sequence.
Tightening Torque 25 Nm
Notice
Tighten the No. 1 bolts(light arrow) first and then tighten the No. 2 bolts(dark arrow) stage by stage.
OM662LA OM661LA

OM600 ENGINE MECHANICAL 1B3-61
38. Replace the O-ring of heater feed pipe and install it to thecylinder head. NoticeFor installation, clean the hole.
39. Install the bracket of heater feed pipe to the oil filter.
40. Install the fuel pipe and the accelerator control linkage.
41. Connect the fuel lines to the injection nozzles and to the injection pump. Box Wrench Insert 000 589 77 03 00
Tightening Torque 18 Nm

1B3-62 OM600 ENGINE MECHANICAL
43. By inserting a rod into the tensioning lever upper hole andpulling the rod, install the bolt and then tighten the nut.
44. Install the oil dipstick tube bracket.
Tightening Torque 10 Nm
45. Hold the cooling fan with the counter holder and tighten the bolt.
42. Install the poly V-belt.
Notice Be careful not to contaminate the belt.
Tightening Torque 23 Nm

OM600 ENGINE MECHANICAL 1B3-63
TIMING CASE COVER
Preceding Work : Removal of the cooling fanRmoval of the V-belt tensioning device Removal of the vibration damper and hub Removal of the alternator
1 Bolt............................................................ 10Nm
2 Cylinder Head Cover
3 Gasket ................................................... Replace
4 Socket Bolt ................................................ 25Nm
5 Fuel Filter
6 Square Nut
7 Oil Pan
8 Socket Bolt ................................................ 10Nm
9 Bolt .................................................... M6 : 10Nm
M8 : 23Nm 10 Power Steering Pump
11 Bolt
12 Belt Pulley 13 Bolt
............................................................ 32Nm
14 Timing Case Cover
15 Bolt ............................................................ 23Nm
16 Alternator Bracket
17 Bolt ............................................................ 45Nm
18 Bolt ............................................................ 25Nm
19 Bolt ............................................................ 10Nm
20 Closing Cover
21 Socket Bolt ................................................ 23Nm
22 Guide Pulley
23 Bolt .............................................................. 9Nm
24 Guide Pulley Bracket
25 Nut ............................................................. 23Nm

1B3-64 OM600 ENGINE MECHANICAL
8. Remove the guide pulley bracket (24).
Tools Required
116 589 03 07 00 Socket Wrench Removal Procedure
1. Remove the fan clutch and cooling fan belt pulley.
2. Drain the engine oil completely.
3. Remove the oil dipstick tube bracket bolts.
4. Remove the crankshaft pulley.
5. Loosen the bolt (1) and then remove the cylinder head cover(2) and gasket.
6. Remove the vacuum pump.
7. Detach the closing cover (20). Remove the bolts(21) and then remove the guide pulley (22).

1B3-66 OM600 ENGINE MECHANICAL
18. Remove the timing case cover (19) bolts and then removethe timing case cover (14). Notice Be careful not to damage the cylinder head gasket or oil pan gasket.
13. Remove the camshaft.
14. Remove the socket bolts(4) in the chain box.
Socket Wrench 115 589 03 07 00
15. Remove the injection pump. NoticeSee the ‘Removal of fuel injection pump ’.
16. Remove the oil pan bolts (8, 9) in the area of the timing case cover (14).
17. Slightly loosen the remaining oil pan bolts.

OM600 ENGINE MECHANICAL 1B3-67
Installation Procedure
1. Thoroughly clean the sealing surface and apply sealant.
2. Install the timing case cover.Notice Bolts arrangement
1.M6 x 60
2.M6 x 70
3.M6 x 40
3. Tighten the socket bolts in the chain box.
Tightening Torque 10 Nm
Tightening Torque 23 Nm
4. Tighten the oil pan bolts.
Tightening Torque 10 Nm 10 Nm23 Nm
Socket bolt
M6 bolt M8 bolt