2003 Peugeot 307 CC ESP

22-09-2003
INSTRUMENTS AND CONTROLS29
PETROL INSTRUMENT PANEL DIALS: AUTOMATIC GEARBOX
1 - Rev counter.
2 - Seat belt not fastened warning light.
3 - Engine diagnostics warninglight.
4 - Handbrake and low brake fluidlevel warning light.
5 - Left-hand direction indicator.
6 - Coolant temperature indicator.
7 - Battery charge warning light. 8 -
Central (STOP) warning light.
9 - Low fuel level warning light.
10 - Engine oil pressure warning light.
11 - Fuel gauge.
12 - Right-hand direction indicator.
13 - ABS warning light.
14 -
Air bags and rear, protective,pop-up roll-over hoops warning light.
15 - Passenger air bag disarming indicator light.
16 - Speedometer.
17 - Service indicator, oil level and
total distance recorder.
18 - Trip recorder zero reset.
19 - Rear fog lamp indicator light.
20 - ESP/ASR warning light.
21 - Front fog lamps indicator light.
22 - Main beam headlamps indicator light.
23 - Dipped beam headlampsindicator light.
24 - Lighting rheostat.
25 - Engine oil temperature gauge.
26 - Snow programme indicatorlight.
27 - Gear lever position indicator.
28 - Sport programme indicator light.

22-09-2003
INSTRUMENTS AND CONTROLS31
Electronic stability programme (ESP/ASR)warning light
This comes on for 3 seconds each time the ignition is switched on. If the light remains on or comes on when the engine is running and thevehicle is moving, it is accompaniedby an audible signal and the mes-sage "ESP/ASR not functioning"
on the multi-function display; contact
a PEUGEOT dealer. When the engine is running and the vehicle is moving, it flashes if thesystem is activated. It is lit permanently when it is disarmed.
Battery charge warning light
This comes on each time the ignition is switched on. If it comes on with the engine run- ning, it is accompanied by an audiblesignal and a message "Battery
charge fault" on the multi-function
display. It can indicate:
Ð faulty operation of the charging circuit,
Ð loose battery or starter terminals,
Ð a cut or slack alternator belt,
Ð an alternator fault.
Contact a PEUGEOT dealer.
Engine diagnostics warning light This comes on each time
the ignition is switched on. If it flashes when the engine is run- ning, accompanied by an audiblesignal and the message "Catalytic
converter fault" on the multi-func-
tion display, it indicates a malfunctionin the injection or ignition system.There is a risk of damage to the
catalytic converter.
Contact a PEUGEOT dealer as soon as possible. Passenger air bag disarmed indicatorlight
Illumination of this warning light is accompanied by an audible signaland the message "Passenger air
bag deactivated" on the multi-func-
tion display. If the passager air bag is disarmed, the indicator light comes on whenthe ignition is switched on andremains on. In all cases, if the warning light flashes,
contact a PEUGEOT dealer.
Air bags and rear, protective, pop-uproll-over hoopswarning light
This light comes on for a few seconds when the ignition is switched on. Illumination of this warning light, with the engine running, is accompaniedby an audible signal and a messageon the multi-function display: Ð "Air bag fault" , indicates a fault in
the front air bags or side air bags,
Ð "Roll-over hoops fault" , indicates
a fault in the pop-up roll-over hoops (located in the rear head restraints).
Contact a PEUGEOT dealer.
or
ABS warning light This light comes on for 3 seconds each time the ignition is switched on. If it remains on or comes on above
8 mph (12 kmh), this indicates a mal-
function of the ABS.
However, the vehicle retains conven- tional servo-assisted braking. Illumination of this light is accompa-nied by an audible signal and themessage
"ABS fault" on the multi-
function display.
Contact a PEUGEOT dealer.

22-09-2003
Lighting rheostat With the lights on, press the button tovary the intensity of thelighting of the instru-ments and controls.
When the lighting reaches the mini-mum (or maximum) setting, release thebutton then press it again to increase(or reduce) the brightness. As soon as the lighting is of the required brightness, release the button.
Trip recorder zero reset With the ignition on, press the button.
Instrument panel display After switching on the ignition, three functions are shown in succession:
Ð service indicator (see corresponding section),
Ð engine oil level indicator,
Ð total distance recorder (total and trip distances).Note:
the total and trip distances are displayed for 30 seconds when the ignition
is switched off, on opening the driver's door, as well as on locking and unlocking the vehicle. Engine oil level indicator When the ignition is switched on, the engine oil level is indicated for approxi- mately 10 seconds, after the servicing information.
Surplus oil Flashing indicates a surplus of oil which can cause damage to the engine. If the surplus of oil is confirmed by checking using the dipstick,
contact a PEUGEOT dealer without delay. No oil Flashing indicates a lack of oil which can cause damage to the engine. If the lack of oil is confirmed by checking using the dipstick, it is essential to top up the level. Oil level gauge fault Check the oil level using the dipstick. If the level is correct, the flashing indicates a true engine oil level gauge fault.
Contact a PEUGEOT dealer.
INSTRUMENTS AND CONTROLS
34
The value obtained by checking the level using the dipstick is only correct if the vehicle has been on level ground, with the engine off, for more than 10 min
utes.

22-09-2003
YOUR 307 CC IN DETAIL35
MULTI-FUNCTION SCREENS Presentation Monochrome screen B This enables the following information to be displayed:
Ð the time,
Ð the date,
Ð the outside temperature (the
¡C
symbol flashes when there is a risk of ice),
Ð the radio displays,
Ð the status of the openings (doors, bonnet...),
Ð the warning messages (e.g. "Bat- tery charge fault") or information messages (e.g. "Passenger airbag deactivated") displayedtempo-rarily can be cleared bypressing button 1or 2,
Ð the trip computer (see corres- ponding section). Monochrome screen CT andcolour screen DT These two systems are controlled by the
RT3 audio/telephone keypad.
They enable the following informa-tion to be displayed:
Ð the time,
Ð the date,
Ð the outside temperature (a message warns you when there is a risk of ice),
Ð the audio source displays (radio, CD, ...),
Ð the telematic system displays (telephone, services, ...),
Ð the status of the openings (doors, bonnet, ...),
Ð the warning messages (e.g. "Fuel level low") and vehicle functionsstatus messages (e.g. "Passengerair bag deactivated") displayed
temporarily,
Ð the trip computer display (see cor- responding section),
Ð the satellite navigation system displays (see corresponding sec-tion).
Note: to enable you to use all of your
system's functions, you have twoCD ROMs: one, "Configuration",
contains the software and the various
display and spoken information lan-
guages, the other, "Navigation",contains the satellite navigation sys-tem map data. Monochrome screen CT Main menu
Press the RT3 audio/telephone "MENU"
button to access the main
menu and select one of the following
applications:
Ð navigation - guidance (see section "Satellite navigation system"),
Ð trip computer (see corresponding section),
Ð directory (see "RT3 audio/tele- phone" section),
Ð telematics (see "RT3 audio/tele- phone" section),
Ð configuration (see corresponding section).

22-09-2003
YOUR 307 CC IN DETAIL
36
Parameter configuration Monochrome screen B Press button
1for two seconds to
gain access to the settings.
Then, each press of this button permits scrolling of the various parameters.
Ð language of the information displayed,
Ð unit of speed (km or miles),
Ð unit of temperature (degrees Celsius or Fahrenheit),
Ð time format (12 or 24 hours),
Ð hour,
Ð minute,
Ð year,
Ð month,
Ð day.Pressing button 2enables you to
change the parameter selected. Continue pressing the button forrapid scrolling. After ten seconds without action, the
screen returns to the usual display,the modified data are recorded.
Ð configuration (see corresponding
section),
Ð map (see section "Satellite naviga- tion system").
A few definitions Superimposed display: a window appears over the current application for a short while, toannounce a change of status ofanother application. Permanent application: main application currently in use, displayed in the main screen
window. Contextual menu: limited menu associated with the main application currently in use,displayed in the main screen
window.
Colour screen DT Main menu
Press the RT3 audio/telephone "MENU"
button to access the main
menu and select one of the following
applications:
Ð navigation - guidance (see section "Satellite navigation system"),
Ð trip computer (see corresponding section),
Ð directory (see "RT3 audio/tele- phone" section),
Ð telematics (see "RT3 audio/tele- phone" section),

22-09-2003
YOUR 307 CC IN DETAIL
36
Parameter configuration Monochrome screen B Press button
1for two seconds to
gain access to the settings.
Then, each press of this button permits scrolling of the various parameters.
Ð language of the information displayed,
Ð unit of speed (km or miles),
Ð unit of temperature (degrees Celsius or Fahrenheit),
Ð time format (12 or 24 hours),
Ð hour,
Ð minute,
Ð year,
Ð month,
Ð day.Pressing button 2enables you to
change the parameter selected. Continue pressing the button forrapid scrolling. After ten seconds without action, the
screen returns to the usual display,the modified data are recorded.
Ð configuration (see corresponding
section),
Ð map (see section "Satellite naviga- tion system").
A few definitions Superimposed display: a window appears over the current application for a short while, toannounce a change of status ofanother application. Permanent application: main application currently in use, displayed in the main screen
window. Contextual menu: limited menu associated with the main application currently in use,displayed in the main screen
window.
Colour screen DT Main menu
Press the RT3 audio/telephone "MENU"
button to access the main
menu and select one of the following
applications:
Ð navigation - guidance (see section "Satellite navigation system"),
Ð trip computer (see corresponding section),
Ð directory (see "RT3 audio/tele- phone" section),
Ð telematics (see "RT3 audio/tele- phone" section),

22-09-2003
YOUR 307 CC IN DETAIL43
Manual station search Press the "MAN" button.
Briefly press button Jor Lto increase or decrease the frequency displayed.
By continuing to press the button in the direction selected, you will obtain continuous scrolling of the frequency. The scrolling stops at the first station found as soon as the button is released.Pressing the "MAN"button again returns you to automatic station search.
Manual storing of stations in the memory Select the station required. Press one of the buttons "1"to "6" for more than two seconds.
The sound stops then becomes audible again, confirming that the station has been stored in the memory. Automatic storing of FM stations in the memory (autostore)
Press button Odown for more than two seconds.
Your radio automatically stores the six stations with the strongest signal in FM. These stations are stored in the FMast wave-
band.
If it is not possible to find 6 stations, the remaining memories are empty. Recalling stations stored in the memory For each waveband, briefly press one of the buttons "1" to"6" to recall the corresponding station.

22-09-2003
YOUR 307 CC IN DETAIL45
PTY function This allows you to listen to stations broadcasting a specific type of programme (news, culture, sport, rock etc.). With FMselected, press the "TA" button for more than two seconds to switch this function on or off.
To search for a PTYprogramme:
Ð select the PTYfunction,
Ð briefly press button Jor Lto scroll down the list of the various types of programmes offered.
Ð when the programme of your choice is displayed, keep button Jor Lpressed for more than
two seconds to carry out an automatic search (after an automatic search the PTYfunction is
switched off).
In PTY mode the different types of programmes can be stored in memory. To do this, press the preselection buttons "1" to "6"
for more than two seconds. Briefly press the corresponding button to recall the type of programme stored in the memory.
EON system
This connects stations which are part of the same network. It enables the broadcasting of traffic information or a PTYpro-
gramme by a station that is part of the same network as the station to which you are listening. This service is available when you have selected the TAtraffic information programme or the PTYfunction.