Page 147 of 173
22-09-2003
PRACTICAL INFORMATION135
CHANGING A BULB Front lights Note:
on the right-hand side, remove the style cover, fixed
with two plastic screws, to access the bulbs. Handle the bulbs with a dry cloth.
1 - Dipped beam headlamps (H7-55 W).
2 - Main beam headlamps (H1-55 W).
3 - Front fog lamps (H1-55 W). Turn the protective cover corresponding to the faulty
bulb a quarter of a turn and remove it.
Disconnect the connector.
Press the end of the securing clip to free it. Change the bulb. When fitting the new bulb, ensure that the direction notches are positioned correctly and the securing clip
is fixed properly.
Reconnect the connector.
Refit the protective cover, positioning it with the arrowupwards, then turn it a quarter of a turn to the right. The headlamps are fitted with polycarbonate glass with aprotective coating.
Do not clean them with a dry or abra-
sive cloth, nor with a detergent or solvent product .
Use a sponge and soapy water.
4 - Side lights (W 5 W). Pull the socket rearwards, remove the bulb and
change it.
5 - Direction indicators (PY 21 W amber). Turn the bulb holder a quarter of a turn and remove it.
Change the bulb.
Note: In certain climatic conditions (low temperature,
humidity), condensation inside the headlamp glass is
normal ; it disappears a few minutes after the lights are
switched on.
Page 148 of 173
22-09-2003
PRACTICAL INFORMATION
136
Direction indicator side
repeaters (WY 5 W amber).
Push the repeater forwards and
release the assembly.
Hold the connector and turn thelens a quarter turn.
Change the bulb. Rear lights
1 - Brake lights (diodes).
2 - Side lights (diodes).
3 - Direction indicators (P 21 W).
4 - Reversing light (P 21 W),
left side.
Fog lamp (P 21 W), right side. Direction indicators
Remove the 3 bolts of the corre- sponding boot side trim to access
the light (use the 20 Torx TM
adaptor
of tool Clocated in the handbook
pocket),
Remove the light fixing nut insidethe boot,
Remove the light,
Unscrew the bulb holder 5a
quarter of a turn,
Remove the bulb holder,
Change the faulty bulb.
Note: When refitting, take care to
position the bulb holder and the light
correctly.
Amber coloured bulbs
(direction indicators andside repeaters), must bereplaced with bulbs ofidentical specification
and colour.
All work on the diode lights must be carried out
by a PEUGEOT dealer.
Page 149 of 173
22-09-2003
PRACTICAL INFORMATION
136
Direction indicator side
repeaters (WY 5 W amber).
Push the repeater forwards and
release the assembly.
Hold the connector and turn thelens a quarter turn.
Change the bulb. Rear lights
1 - Brake lights (diodes).
2 - Side lights (diodes).
3 - Direction indicators (P 21 W).
4 - Reversing light (P 21 W),
left side.
Fog lamp (P 21 W), right side. Direction indicators
Remove the 3 bolts of the corre- sponding boot side trim to access
the light (use the 20 Torx TM
adaptor
of tool Clocated in the handbook
pocket),
Remove the light fixing nut insidethe boot,
Remove the light,
Unscrew the bulb holder 5a
quarter of a turn,
Remove the bulb holder,
Change the faulty bulb.
Note: When refitting, take care to
position the bulb holder and the light
correctly.
Amber coloured bulbs
(direction indicators andside repeaters), must bereplaced with bulbs ofidentical specification
and colour.
All work on the diode lights must be carried out
by a PEUGEOT dealer.