2003 Peugeot 307 CC ESP
[x] Cancel search: ESPPage 89 of 173
22-09-2003
YOUR 307 CC IN DETAIL87
The ISOFIX KIDDY child seat* It can be fitted in the "rear facing" position from birth to 13 kg and in the"forwards facing" position from 9 to18 kg.
In the rear, in the "forwards facing" position, it is imperative that the frontseat is in the mid-way position on the
runner, seat back upright. In the "rear facing" position, the body of the child seat must be in contactwith the back of the correspondingfront seat.The ISOFIX R…MER Duo child seat* This seat must only be fitted in the "forwards facing" position for chil-dren weighing between 9 and 18 kg.It is secured without the upper strap
called the Top Tether. For your child's comfort, three seat body angles are possible: upright,reclining and flat. When the Ršmer Duo is installed in
the rear, the vehicle's front seat mustbe adjusted so that the child's feet donot touch the back of the front seat.These seats can also be used onseats not fitted with ISOFIX mount-ings. In this case it is compulsory toattach them to the vehicle's seat bymeans of the three-point seat belt. Refer to the "Summary table for fitting child seats". Follow the instructions for fitting the child seat in the seat manufac-turer's instruction booklet.
* You can only fit ISOFIX child seats
approved by PEUGEOT on your vehicle's ISOFIX mountings.
Page 103 of 173
22-09-2003
YOUR 307 CC IN DETAIL
98
LOCKING/UNLOCKING WITH
A BATTERY FAILURE Driver's door Insert the key in the lock to lock or
unlock the door.Passenger's door
Ð to lock, insert the key in the lock
(located on the edge of the door) then turn an eighth of a turn to
the left.
Ð to unlock, use the interior door opening control (see correspond-ing section).
Boot
The boot is locked, contact a PEUGEOT
dealer.
Page 105 of 173
22-09-2003
YOUR 307 CC IN DETAIL101
Closing the roof:
Carry out the preparatory operations, indicated on the previous page.
Then, press button 3until the roof closing operation is
complete, confirmed by an audible signal.
When carrying out this manoeuvre, the four windows
lower, the boot opens, the moving shelf and the roof unfoldand position themselves, the hinged covers fold, then theboot closes. Note: if you continue to press button 3once the cycle is
complete, the four windows rise again. The control buttons for the windows become operational again at the end of the roof operation. In the case of an electric or hydraulic malfunction of the
roof, it is possible to close the roof manually. Please consult the breakdown procedure described at the end of this handbook.
During roof opening and closing operations, to
avoid any risk of injury, ensure that there is no-one in the proximity of the moving parts.
Operation of the roof is the sole responsibility of
the driver.
To guarantee correct operation, do not release but-ton 3 when the roof is in an intermediate position
(neither completely open or closed). However, in the
event of danger, release the control knob and the
operation will stop instantly. Once the danger hasbeen eliminated, complete the operation.
Page 118 of 173
22-09-2003
YOUR 307 CC IN DETAIL109
ELECTRIC WINDOWS
1 - Driver's electric window
switch.
2 - Passenger's electric window switch.
3 - Rear right electric window switch.
4 - Rear left electric window switch.
5 - Disarming of the rear electric window switches (child lock). Front windows safety auto-reverse When the window rises and meets an obstacle, it stops and partiallylowers again. Note: In the event of unwanted opening of the window on closing (for examplein the presence of frost), press the
switch until it opens completely, thenpull it immediately until it closes.Continue to hold the switch forapproximately one second after thewindow has closed. The safety auto-reverse function is not active during these operations. Disarming the rear window controls For the safety of your children, press switch
5to prevent operation of the
rear windows irrespective of theirposition. When the button is raised, the controls are disarmed. When thebutton is lowered, the controls areactive.
You have two options: Manual operation:
Press or pull the switch gently. The window stops as soon as the switchis released. Automatic operation: Press or pull the switch fully: the window opens or closes completelywhen the switch is released.Pressing the switch again stops the
movement of the window. Note: when one of the doors is
opened or approximately 45 sec- onds following removal of the igni-
tion key, none of the windows can be
opened or closed. The ignition mustbe switched on again to permitopening or closing of the windows.
Page 119 of 173
22-09-2003
YOUR 307 CC IN DETAIL
110
EXTERIOR MIRRORS Electric rear view mirrors
Ð Slide switch Ato the right or to the
left to select the corresponding
mirror.
Ð Move knob Bin all four directions
to adjust.
Ð Return switch Ato the centre
position.
When parked, the mirrors can be folded back electrically by pullingknob Arearwards or automatically
when locking the vehicle.
The exterior mirrors are unfolded by switching on the ignition to the sec-ond notch or to the ON position.
Note: the function that controls fold-
ing of the mirrors when locking thevehicle can be disarmed. Contact a
PEUGEOT dealer.SIMULTANEOUS CONTROL
OF ALL 4 WINDOWS Control 6opens or closes all of the
windows simultaneously.
To disarm the action of control 6on
the rear windows, press the rear win- dows disarming control 5.
Operation of the simulta- neous control of all fourwindows is the sole
responsibility of the driver.
Always remove the key from the ignition whenleaving the vehicle, evenfor a short time.
In the event of contact duringoperation of the windows, youmust reverse the movement of the
window. To do this, press theswitch concerned. When the driver operates the pas- senger electric window switches,he must ensure that no one is preventing correct closing of thewindows. The driver must ensure that the passengers use the electric
windows correctly. Be aware of children when opera- ting the windows.
REINITIALISING THE ELECTRIC WINDOWS Following reconnection of the battery or in the event of a malfunction,release the switch and pull it again
until it closes completely. Hold theswitch for approximately one secondafter closing. The safety auto-reverse function is not active during these operations.
Page 126 of 173
YOUR 307 CC IN DETAIL117
S
: sport programme
: snow programme
P ark: to immobilise the vehicle or start the engine ,
with the handbrake on or off.
R everse: to reverse(select this function with the vehi-
cle stationary, engine at idle).
N eutral: to start the engine and to park, with the hand-
brake on. Note: if function Nis engaged inadvertently while dri-
ving, allow the engine to return to idle before engaging function Dto accelerate.
D rive: for drivingin automatic mode.
M anual: for drivingin manual mode. Moving off
With the engine running, to move off from position
P:
it is essential to press the
brake pedal to exit position P,
select function R, D or M, then
gradually release the pressureon the brake pedal; the vehicle
moves off immediately.
You can also move off from positionN :
release the handbrake, with yourfoot on the brake,
select function R, D or M, then
gradually release the pressureon the brake pedal; the vehicle
moves off immediately.
WARNING When the engine is at idle, brakes not applied, if function R, D or Mis
selected the vehicle moves evenwithout the accelerator beingpressed. For this reason, do not leave chil-
dren unsupervised inside the vehicle, with the engine running .
When maintenance operations needto be carried out with the engine run-ning, apply the handbrake and selectposition P.
"PORSCHE TIPTRONIC SYSTEM" AUTOMATIC GEARBOX The four speed automaticgearbox offers a choice between the comfort of inte-
gral automatic operation , enhanced by a sportand a snow programme, or the
pleasure of manual gear changing .
Gear selection gate Move the lever in the gate to select a function. Once the function is selected, the corresponding indicator light appears on
the instrument panel display.
22-09-2003
Page 131 of 173
22-09-2003
YOUR 307 CC IN DETAIL121
TRACTION CONTROL (ASR)
AND DYNAMIC STABILITY
CONTROL (ESP) These systems are linked and com-
plement the ABS.
The ASR system optimises drive to prevent the wheels skidding, by act-ing on the brakes of the drive wheelsand on the engine. It also allows thedirectional stability of the vehicle tobe improved on acceleration. If there is a variation between the tra- jectory followed by the vehicle and
that required by the driver, the ESPsystem automatically acts on theengine and the brake of one or morewheels, in order to put the vehicleback on course.Disarming the ASR/ESP systems In exceptional conditions (starting a vehicle which is bogged down, stuck
in snow, on soft ground, ...), it may
be advisable to disarm the ASR and
ESP systems, so that the wheels canmove freely and regain grip.
Press the "ESP OFF" switch,
located on the central section of the fascia.
The switch lights up and thewarning light comes on: the
ASR and ESP systems aredisarmed.
These are triggered again: automatically if the ignition is
switched off,
automatically above 30 mph
(50 km/h),
manually by pressing the switchagain.
Operation of the ASR and
ESP systems
The warning light flashes if
the ASR or ESP is activated.Operating check
When a malfunction of the systems occurs, the switchlight flashes and the warninglight comes on, accompa-nied by an audible signal
and the message "ESP/ASR not
functioning" on the multifunction
display.
Contact a PEUGEOT dealer to have the system checked.
The ESP/ASR systems offer exceptional safety innormal driving, but thisshould not encourage thedriver to take extra risks or
drive at high speed. The correct functioning of these systems depends on observationof the manufacturer's recommen-dations regarding the wheels (tyresand rims), the braking components,the electronic components, and thePEUGEOT assembly and opera-tion procedures. After an impact, have the system
checked by a PEUGEOT dealer.
Page 147 of 173
22-09-2003
PRACTICAL INFORMATION135
CHANGING A BULB Front lights Note:
on the right-hand side, remove the style cover, fixed
with two plastic screws, to access the bulbs. Handle the bulbs with a dry cloth.
1 - Dipped beam headlamps (H7-55 W).
2 - Main beam headlamps (H1-55 W).
3 - Front fog lamps (H1-55 W). Turn the protective cover corresponding to the faulty
bulb a quarter of a turn and remove it.
Disconnect the connector.
Press the end of the securing clip to free it. Change the bulb. When fitting the new bulb, ensure that the direction notches are positioned correctly and the securing clip
is fixed properly.
Reconnect the connector.
Refit the protective cover, positioning it with the arrowupwards, then turn it a quarter of a turn to the right. The headlamps are fitted with polycarbonate glass with aprotective coating.
Do not clean them with a dry or abra-
sive cloth, nor with a detergent or solvent product .
Use a sponge and soapy water.
4 - Side lights (W 5 W). Pull the socket rearwards, remove the bulb and
change it.
5 - Direction indicators (PY 21 W amber). Turn the bulb holder a quarter of a turn and remove it.
Change the bulb.
Note: In certain climatic conditions (low temperature,
humidity), condensation inside the headlamp glass is
normal ; it disappears a few minutes after the lights are
switched on.