2003 NISSAN X-TRAIL seat adjustment

SQUEAK AND RATTLE TROUBLE DIAGNOSES
SE-7
C
D
E
F
G
H
J
K
L
MA
B
SE

TRUNK
Trunk noises are often caused by a loose jack or loose items put into the trunk by the owner.
In addition look for:
1. Trunk lid dumpers out of adjustment
2. Trunk lid striker out of adjustment
3. Trunk lid torsion bars knocking together
4. A loose license plate or bracket
Most of these incidents can be repaired by adjusting, securing or insulating the item(s) or component(s) caus-
ing the noise.
SUNROOF/HEADLINING
Noises in the sunroof/headlining area can often be traced to one of the following:
1. Sunroof lid, rail, linkage or seals making a rattle or light knocking noise
2. Sunvisor shaft shaking in the holder
3. Front or rear windshield touching headlining and squeaking
Again, pressing on the components to stop the noise while duplicating the conditions can isolate most of these
incidents. Repairs usually consist of insulating with felt cloth tape.
SEATS
When isolating seat noise it's important to note the position the seat is in and the load placed on the seat when
the noise is present. These conditions should be duplicated when verifying and isolating the cause of the
noise.
Cause of seat noise include:
1. Headrest rods and holder
2. A squeak between the seat pad cushion and frame
3. Rear seat back lock and bracket
These noises can be isolated by moving or pressing on the suspected components while duplicating the con-
ditions under which the noise occurs. Most of these incidents can be repaired by repositioning the component
or applying urethane tape to the contact area.
UNDERHOOD
Some interior noise may be caused by components under the hood or on the engine wall. The noise is then
transmitted into the passenger compartment.
Causes of transmitted underhood noise include:
1. Any component mounted to the engine wall
2. Components that pass through the engine wall
3. Engine wall mounts and connectors
4. Loose radiator mounting pins
5. Hood bumpers out of adjustment
6. Hood striker out of adjustment
These noise can be difficult to isolate since they cannot be reached from the interior of the vehicle. The best
method is to secure, move or insulate one component at a time and test drive the vehicle. Also, engine RPM
or load can be changed to isolate the noise. Repairs can usually be made by moving, adjusting securing, or
insulating the component causing the noise.

MA-4
DESCRIPTION

DESCRIPTIONPFP:00000
Pre-delivery Inspection ItemsELS000Y5
Shown below are Pre-delivery Inspection Items required for the new vehicle. It is recommended that
necessary items other than those listed here be added, paying due regard to the conditions in each
country.
Perform applicable items on each model. Consult text of this section for specifications.
Install vehicle protection kit
Fit all accessories ordered (if applicable) (e.g. towbar, audio, navigation, air conditioner, styling kit)
UNDER HOOD — engine off
Check coolant level and cooling system for leaks
Charge battery and check terminals for condition
Check drive belts tension (diesel only)
Check fuel filter for water or dust (diesel only) and fuel system for leaks
Check engine oil level and for oil leaks
Check brake and clutch fluid levels and fluid lines for leaks
Check and top up washer reservoirs
Check power steering fluid level and fluid lines for leaks (if applicable)
Check air conditioning system for gas leaks (if applicable)
ON INSIDE AND OUTSIDE
Install transit fuse if removed for vehicle storage
Check instruments, gauges, lamps, horn and accessories for operation
Check wipers and washers for operation and adjustment
Check interior and door mirrors and sun visors for operation
Set radio code and set clock
Check parking brake adjustment
Check clutch pedal adjustment
Check steering lock operation
Check seat adjusters and seat belts for operation
Check all windows for operation and alignment
Check mouldings, trim and fittings for fit and alignment
Check weatherstrips for fit and adhesion
Check hood, trunk lid, door panels and fuel lid for fit and alignment
Check latches, keys, remote key, door locks and remote trunk lid and fuel lid release for operation
Check wheel nut torques
Check tyre pressure (incl. spare tyre)
Check tool kit and jack for operation
Check automatic transmission/transaxle starter inhibitor (if applicable)
Check sunroof for operation and alignment (if applicable)
UNDER BODY
Check manual transmission/transaxle, differential and transfer box for oil level and oil leaks
Tighten bolts and nuts steering linkage and gear box, axle/suspension parts, propeller and exhaust system
Check brake and clutch lines, and oil/fluid reservoirs for leaks
Remove front suspension spacer blocks (if applicable)
Check body mounting torque (if applicable)

MTC-1
MANUAL AIR CONDITIONER
J AIR CONDITIONER
CONTENTS
C
D
E
F
G
H
I
K
L
M
SECTION
A
B
MTC

MANUAL AIR CONDITIONER
PRECAUTIONS .......................................................... 2
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 2
Wiring Diagrams and Trouble Diagnosis .................. 2
TROUBLE DIAGNOSIS .............................................. 3
How to Perform Trouble Diagnoses for Quick and
Accurate Repair ....................................................... 3
WORK FLOW ........................................................ 3
SYMPTOM TABLE ................................................ 3
Component Parts and Harness Connector Location ..... 4
PASSENGER COMPARTMENT ........................... 4
Discharge Air Flow ................................................... 5
Wiring Diagram —HEATER— .................................. 6
Operational Check ................................................... 7
CHECKING BLOWER ........................................... 7
CHECKING DISCHARGE AIR .............................. 7
CHECKING RECIRCULATION ............................. 7
CHECKING TEMPERATURE DECREASE .......... 8
CHECKING TEMPERATURE INCREASE ............ 8
Mode Door ............................................................... 9
INSPECTION FLOW ............................................. 9
Air Mix Door ........................................................... 10
INSPECTION FLOW ........................................... 10
Intake Door Motor Circuit ........................................ 11
INSPECTION FLOW ............................................ 11
COMPONENT DESCRIPTION ............................ 11
DIAGNOSTIC PROCEDURE FOR INTAKE
DOOR MOTOR ................................................... 12
Blower Motor Circuit ............................................... 15
INSPECTION FLOW ........................................... 15
DIAGNOSTIC PROCEDURE FOR BLOWER
MOTOR ............................................................... 16
COMPONENT INSPECTION .............................. 18
Insufficient Heating ................................................. 19
INSPECTION FLOW ........................................... 19
CONTROLLER ......................................................... 21
Removal and Installation ........................................ 21
REMOVAL ........................................................... 21INSTALLATION ................................................... 21
Disassembly and Assembly .................................... 21
BLOWER UNIT ......................................................... 22
Removal and Installation ........................................ 22
REMOVAL ........................................................... 22
INSTALLATION ................................................... 22
Disassembly and Assembly .................................... 23
BLOWER MOTOR .................................................... 24
Removal and Installation ........................................ 24
REMOVAL ........................................................... 24
INSTALLATION ................................................... 24
BLOWER FAN RESISTOR ....................................... 25
Removal and Installation ........................................ 25
REMOVAL ........................................................... 25
INSTALLATION ................................................... 25
INTAKE DOOR MOTOR ........................................... 26
Removal and Installation ........................................ 26
REMOVAL ........................................................... 26
INSTALLATION ................................................... 26
HEATER UNIT ........................................................... 27
Removal and Installation ........................................ 27
REMOVAL ........................................................... 27
INSTALLATION ................................................... 28
Disassembly and Assembly .................................... 29
HEATER CORE ......................................................... 30
Removal and Installation ........................................ 30
REMOVAL ........................................................... 30
INSTALLATION ................................................... 30
MODE DOOR ............................................................ 31
Control Linkage Adjustment ................................... 31
MODE DOOR CONTROL CABLE ....................... 31
AIR MIX DOOR ......................................................... 32
Control Linkage Adjustment ................................... 32
AIR MIX DOOR CONTROL CABLE .................... 32
DUCTS AND GRILLES ............................................. 33
Removal and Installation ........................................ 33
REMOVAL ........................................................... 33
INSTALLATION ................................................... 36

WW-1
WIPER, WASHER & HORN
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION
A
B
WW

WIPER, WASHER & HORN
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Wiring Diagrams and Trouble Diagnosis .................. 3
FRONT WIPER AND WASHER SYSTEM .................. 4
System Description .................................................. 4
WIPER OPERATION ............................................ 4
WASHER OPERATION ......................................... 4
Wiring Diagram — WIPER — .................................. 6
Wiring Diagram — WIPER —/LHD models .............. 7
Terminal and Reference Values for Combination
Switch ....................................................................... 8
Removal and Installation for Front Wiper Arms,
Adjustment for Wiper Arms Stop Location ............... 8
Removal and Installation for Wiper Motor and Link-
age ........................................................................... 9
REMOVAL ........................................................... 10
INSTALLATION ................................................... 10
Washer Nozzle Adjustment ..................................... 11
Washer Tube Layout ............................................... 11
Removal and Installation for Washer Nozzle ......... 12
REMOVAL ........................................................... 12
INSTALLATION ................................................... 12
Inspection for Washer Nozzle ................................ 12
CHECK VALVE ................................................... 12
Removal and Installation for Wiper and Washer
Switch ..................................................................... 12
REMOVAL ........................................................... 12
INSTALLATION ................................................... 12
Removal and Installation for Washer Tank ............. 13
Removal and Installation for Washer Pump ........... 13
REAR WIPER AND WASHER SYSTEM .................. 14
Wiring Diagram — WIP/R — .................................. 14
Terminal and Reference Values for Combination
Switch ..................................................................... 16
Removal and Installation for Rear Wiper Arms ...... 16
WIPER ARMS ..................................................... 16
Removal and Installation for Wiper Motor and Link-
age ......................................................................... 17REMOVAL ........................................................... 17
INSTALLATION ................................................... 17
Washer Nozzle Adjustment .................................... 18
Removal and Installation for Rear Washer Nozzle ... 18
REMOVAL ........................................................... 18
INSTALLATION ................................................... 18
Inspection for Washer Nozzle ................................. 18
CHECK VALVE .................................................... 18
Removal and Installation for Wiper and Washer
Switch ..................................................................... 19
Removal and Installation for Washer Tank ............. 19
Removal and Installation for Washer Pump ........... 19
Washer Tube Layout .............................................. 19
HEADLAMP WASHER ............................................. 20
System Description ................................................. 20
Wiring Diagram —HLC— ....................................... 21
Wiring Diagram —HLC—/RHD models .................. 22
Removal and Installation for Washer Nozzle .......... 23
REMOVAL ........................................................... 23
INSTALLATION ................................................... 23
Inspection for Washer Nozzle ................................. 23
CHECK VALVE .................................................... 23
Removal and Installation for Washer Tank ............. 23
Removal and Installation for Washer Pump ........... 23
Washer Tube Layout .............................................. 24
HORN ........................................................................ 25
Wiring Diagram — HORN — .................................. 25
Removal and Installation ........................................ 26
REMOVAL ........................................................... 26
INSTALLATION ................................................... 26
CIGARETTE LIGHTER ............................................. 27
Wiring Diagram — CIGAR — ................................. 27
Removal and Installation ........................................ 28
REMOVAL ........................................................... 28
INSTALLATION ................................................... 28
POWER SOCKET ..................................................... 29
Wiring Diagram —POWER SOCKET— ................. 29
Removal and Installation for Front Power Socket ... 30
REMOVAL ........................................................... 30

PG-62
HARNESS

F/FOG LT Front Fog Lamp
F/PUMP EC Fuel Pump
FIAR EC Fuel Injector Adjustment Resistor
FRO2 EC Front Heated Oxygen Sensor
FRO2/H EC Front Heated Oxygen Sensor Heater
FRPS EC Fuel Rail Pressure Sensor
FTP EC Fuel Transport Pump
FTS EC Fuel Temperature Sensor
FTS AT A/T Fluid Temperature Sensor Circuit
FUEL EC Fuel Injection System Function
GLORLY EC Glow Relay
GLOW EC Glow Control System
H/AIM LT Headlamp Aiming Control System
H/LAMP LT Headlamp
H/SEAT SE Heated Seat
HEATER MTC Heater System
HLC WW Headlamp Cleaner
HO2S1 EC Heated Oxygen Sensor 1
HO2S1H EC Heated Oxygen Sensor 1 Heater
HO2S2 EC Heated Oxygen Sensor 2
HO2S2H EC Heated Oxygen Sensor 2 Heater
HORN WW Horn
IATS EC Intake Air Temperature Sensor
IATSEN EC Intake Air Temperature Sensor
IGNSYS EC Ignition System
ILL LT Illumination
INJECT EC Injector
INJ/PW EC Fuel Injector Power Supply Circuit
INT/L LT Map Lamp
IVC EC Intake Valve Timing Control Solenoid Valve
KS EC Knock Sensor
LOAD EC Electrical Load Signal
LPSV AT Line Pressure Solenoid Valve
MAFS EC Mass Air Flow Sensor
MAIN AT Main Power Supply and Ground Circuit
MAIN EC Main Power Supply and Ground Circuit
METER DI Speedometer, Tachometer, Temp. and Fuel Gauges
MIL/DL EC MIL & Data Link Connector
MIRROR GW Door Mirror
MULTI BL Multi-Remote Control System
NATS BL Nissan Anti-Theft System
NAVI AV Navigation System
NONDTC AT Non-Detective Items
OVRCSV AT Overrun Clutch Solenoid ValveCode Section Wiring Diagram Name

LT-1
LIGHTING SYSTEM
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION
A
B
LT

LIGHTING SYSTEM
PRECAUTION ............................................................ 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precaution ................................................................ 3
Wiring Diagrams and Trouble Diagnosis .................. 3
HEADLAMP ................................................................ 4
System Description .................................................. 4
DESCRIPTION ...................................................... 4
LOW BEAM OPERATION ..................................... 4
HIGH BEAM OPERATION/FLASH-TO-PASS
OPERATION ......................................................... 4
DRIVING LAMP OPERATION .............................. 4
Schematic ................................................................ 6
Wiring Diagram — H/LAMP — ................................. 7
LHD MODELS ....................................................... 7
RHD MODELS .................................................... 10
Trouble Diagnoses ................................................. 13
Aiming Adjustment for Headlamp ........................... 14
LOW BEAM ......................................................... 14
Aiming Adjustment for Driving Lamp ...................... 15
PREPARATION BEFORE ADJUSTING .............. 15
ADJUSTMENT USING AN ADJUSTMENT
SCREEN (LIGHT/DARK BORDERLINE) ............ 16
ADJUSTING ........................................................ 16
Bulb Replacement for Headlamp and Clearance
lamp ....................................................................... 16
HEAD LAMP ....................................................... 16
CLEARANCE LAMP ........................................... 16
Bulb Replacement for Driving Lamp ...................... 17
Removal and Installation for Headlamp ................. 17
REMOVAL ........................................................... 17
INSTALLATION ................................................... 17
Removal and Installation for Driving Lamp ............ 18
REMOVAL ........................................................... 18
INSTALLATION ................................................... 18
Removal and Installation for Driving Lamp Switch ... 19
HEADLAMP - DAYTIME LIGHT SYSTEM - ............. 20
System Description ................................................ 20DESCRIPTION .................................................... 20
HEADLAMP OPERATION (DAYTIME LIGHT
CANCEL OPERATION) ....................................... 20
DAYTIME LIGHT OPERATION ........................... 20
DRIVING LAMP OPERATION ............................. 20
Schematic ............................................................... 22
Wiring Diagram -DTRL- .......................................... 23
Trouble Diagnoses ................................................. 28
DAYTIME LIGHT CONTROL UNIT INSPECTION
TABLE ................................................................. 28
Bulb Replacement .................................................. 28
Aiming Adjustment .................................................. 28
Removal and Installation ........................................ 28
HEADLAMP AIMING CONTROL ............................. 29
Wiring Diagram -H/AIM- ......................................... 29
Removal and Installation ........................................ 30
Switch Circuit Inspection ........................................ 30
TURN SIGNAL AND HAZARD WARNING LAMPS ... 31
System Description ................................................. 31
TURN SIGNAL OPERATION .............................. 31
HAZARD LAMP OPERATION ............................. 31
Wiring Diagram — TURN — ................................... 33
LHD MODELS ..................................................... 33
RHD MODELS .................................................... 35
Trouble Diagnoses ................................................. 37
Electrical Components Inspection .......................... 37
COMBINATION FLASHER UNIT CHECK ........... 37
Bulb Replacement .................................................. 38
FRONT TURN SIGNAL LAMP ............................ 38
SIDE TURN SIGNAL LAMP ................................ 38
REAR TURN SIGNAL LAMP .............................. 38
Removal and Installation for Front Turn Signal Lamp ... 38
REMOVAL ........................................................... 38
INSTALLATION ................................................... 38
Removal and Installation for Side Turn Signal Lamp ... 38
Removal and Installation for Rear Turn Signal Lamp ... 39
LIGHTING AND TURN SIGNAL SWITCH ................ 40
Removal and Installation ........................................ 40
Switch Circuit Inspection ........................................ 40

PRECAUTION
LT-3
C
D
E
F
G
H
I
J
L
MA
B
LT

PRECAUTION PFP:00011
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
EKS0079M
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precaution EKS003KS

Do not touch the glass of bulb directly by hand. Keep grease and other oily matters away from it. Do not
touch bulb by hand while it is lit or right after being turned off. Burning may result.

Do not leave bulb out of headlamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of the headlamp. When replacing the bulb, be sure to replace it with a new one.

Adjust aiming by tightening aiming screw. (To adjust it toward loosening side, first loosen adjusting screw,
and then make adjustment by tightening.)

To remove soil or sealant of bulbs, do not use organic solvent (thinner, gasoline, etc.)

When replacing bulb, be sure to hold bulb socket and pull it out straight. If wiring harness of the bulb is
pulled at an angle, the bulb may be caught in the lamp, making it difficult to take out.
Wiring Diagrams and Trouble Diagnosis EKS003KT
When you read wiring diagrams, refer to the followings:

Refer to GI-14, "How to Read Wiring Diagrams" in GI section

Refer to PG-2, "POWER SUPPLY ROUTING" for power distribution circuit in PG section
When you perform trouble diagnosis, refer to the followings:

Refer to GI-10, "HOW TO FOLLOW TEST GROUPS IN TROUBLE DIAGNOSES" in GI section

Refer toGI-23, "How to Perform Efficient Diagnosis for an Electrical Incident" in GI section

IDX-5
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
Front Door Trim ................................................... EI-32
Front fog lamp .................................................... LT-52
Front passenger air bag .................................. SRS-35
Front seat .......................................................... SE-24
Front seat belt ...................................................... SB-3
Front seat belt pre-tensioner .... SB-2, SRS-3, SRS-40
Front side air bag ............................................. SRS-37
Front suspension ............................................... FSU-5
Front washer ...................................................... WW-4
Front wiper ......................................................... WW-4
FRPS - Wiring diagram .................... EC-999, EC-1309
FTS - Wiring diagram ...................... EC-994, EC-1304
FUEL - Wiring diagram ...................... EC-218, EC-225
Fuel check valve ................................ EC-473, EC-865
Fuel cut control (at no load high engine speed) EC-38,
EC-500
, EC-887, EC-1218
Fuel filler lid ...................................................... BL-103
Fuel filter .......................................... EC-890, EC-1221
Fuel filter replacement(QR20DEQR25DE) .......... FL-4
Fuel filter replacement(YD22DDTi) ....... FL-17, MA-31
Fuel gauge ............................................................ DI-4
Fuel injection control system ........... EC-885, EC-1216
Fuel injection system ......................... EC-216, EC-223
Fuel injector adjustment resistor .... EC-1115, EC-1404
Fuel injector and fuel tube(QR20DEQR25DE) . EM-32
Fuel injector and fuel tube(YD22DDTi) ............ EM-157
Fuel line inspection(QR20DEQR25DE) . FL-3, MA-23
Fuel line inspection(YD22DDTi) ............ FL-16, MA-31
Fuel pressure check ............................ EC-48, EC-510
Fuel pressure release .......................... EC-48, EC-510
Fuel pump .......... EC-443, EC-835, EC-890, EC-1127,
EC-1416
Fuel pump and gauge(QR20DEQR25DE) .......... FL-4
Fuel rail pressure sensor ................. EC-997, EC-1307
Fuel system(QR20DEQR25DE) .......................... FL-3
Fuel system(YD22DDTi) ..................................... FL-16
Fuel tank(QR20DEQR25DE) ............................ FL-11
Fuel tank(YD22DDTi) ......................................... FL-23
Fuel temperature sensor ................. EC-993, EC-1303
Fuse ................................................................... PG-12
Fuse and fusible link box ................................... PG-76
Fusible link ......................................................... PG-12
G
Gauges ................................................................. DI-4
Gear components (M/T) ....................... MT-20, MT-25
Generator .......................................................... SC-12
Generator - See Alternator ................................ SC-12
Generic scan tool (GST) .................... EC-112, EC-931
Glass .................................................. GW-80, GW-83
GLOW - Wiring diagram EC-1070, EC-1170, EC-1458
Glow plug ....................................... EC-1169, EC-1457
Glow plug(YD22DDTi) ..................................... EM-152
Glow relay ...................... EC-1069, EC-1169, EC-1457
GPS antenna ..................................................... AV-43
Grille - See Exterior ............................................. EI-19
Ground distribution ............................................ PG-13
H
H/AIM - Wiring diagram ...................................... LT-29
H/LAMP - Wiring diagram ........................... LT-4, LT-7
H/MIRROR - Wiring diagram ............................ GW-21
Harness connector ............................................. PG-70
Harness layout ................................................... PG-30
Headlamp ............................................................. LT-4
Headlamp aiming control .................................... LT-29
Headlamp leveler - See Headlamp aiming control .......
LT-29
Headlamp washer ............................................ WW-20
Headlining - See Roof trim .................................. EI-39
Heated oxygen sensor 1 .... EC-176, EC-183, EC-193,
EC-318
, EC-324, EC-611, EC-618, EC-786
Heated oxygen sensor 1 heater ......... EC-138, EC-771
Heated oxygen sensor 2 .... EC-201, EC-208, EC-330,
EC-338
, EC-792
Heated oxygen sensor 2 heater ......... EC-144, EC-776
Heated seat ........................................... SE-18, SE-21
HEATER - Wiring diagram ................................ MTC-6
Heater and cooling unit (Heater core) ............ ATC-131
Heater mirror ..................................................... GW-21
Heater system - Wiring diagram ....................... MTC-6
Heater unit (heater core) .. ATC-136, MTC-27, MTC-30
HFC134a (R134a) system precaution ............... ATC-4
HFC134a (R134a) system service procedure ATC-141
HFC134a (R134a) system service tools .......... ATC-15
HFC134a system service equipment precaution ..........
ATC-10
HO2S1 - Wiring diaram ...... EC-178, EC-186, EC-196,
EC-613
, EC-620
HO2S1H - Wiring diagram ............................... EC-140
HO2S2 - Wiring diagram .... EC-203, EC-211, EC-333,
EC-341
HO2S2H - Wiring diagram ............................... EC-146
Hood .................................................................. BL-12
Horn ................................................................. WW-25
HORN - Wiring diagram ................................... WW-25
How to erase DTC ........................... EC-514, EC-1223
How to erase DTC for OBD system ..... EC-63, EC-895
I
IATS - Wiring diagram ...... EC-158
, EC-977, EC-1287
IATSEN - Wiring diagram ................................ EC-782
Identification ...................................... ATC-12, ATC-13
Idle air volume learning ........................ EC-46, EC-508
Idle speed ............. EC-79, EC-526, EC-905, EC-1231
Ignition coil ......................................... EC-417, EC-798
Ignition coil(QR20DEQR25DE) ....................... EM-29
Ignition control system ....................... EC-417, EC-798
Ignition timing ....................................... EC-79, EC-526
IGNSYS - Wiring diagram .................. EC-418, EC-799
ILL - Wiring diagram ........................................... LT-66
Illumination .......................................................... LT-66
In vehicle sensor ........... ATC-111, ATC-113, ATC-122
INJE/PW - Wiring diagram ............. EC-1158, EC-1446
INJECT - Wiring diagram . EC-429, EC-821, EC-1008,