2003 NISSAN X-TRAIL wiper fluid

MA-4
DESCRIPTION

DESCRIPTIONPFP:00000
Pre-delivery Inspection ItemsELS000Y5
Shown below are Pre-delivery Inspection Items required for the new vehicle. It is recommended that
necessary items other than those listed here be added, paying due regard to the conditions in each
country.
Perform applicable items on each model. Consult text of this section for specifications.
Install vehicle protection kit
Fit all accessories ordered (if applicable) (e.g. towbar, audio, navigation, air conditioner, styling kit)
UNDER HOOD — engine off
Check coolant level and cooling system for leaks
Charge battery and check terminals for condition
Check drive belts tension (diesel only)
Check fuel filter for water or dust (diesel only) and fuel system for leaks
Check engine oil level and for oil leaks
Check brake and clutch fluid levels and fluid lines for leaks
Check and top up washer reservoirs
Check power steering fluid level and fluid lines for leaks (if applicable)
Check air conditioning system for gas leaks (if applicable)
ON INSIDE AND OUTSIDE
Install transit fuse if removed for vehicle storage
Check instruments, gauges, lamps, horn and accessories for operation
Check wipers and washers for operation and adjustment
Check interior and door mirrors and sun visors for operation
Set radio code and set clock
Check parking brake adjustment
Check clutch pedal adjustment
Check steering lock operation
Check seat adjusters and seat belts for operation
Check all windows for operation and alignment
Check mouldings, trim and fittings for fit and alignment
Check weatherstrips for fit and adhesion
Check hood, trunk lid, door panels and fuel lid for fit and alignment
Check latches, keys, remote key, door locks and remote trunk lid and fuel lid release for operation
Check wheel nut torques
Check tyre pressure (incl. spare tyre)
Check tool kit and jack for operation
Check automatic transmission/transaxle starter inhibitor (if applicable)
Check sunroof for operation and alignment (if applicable)
UNDER BODY
Check manual transmission/transaxle, differential and transfer box for oil level and oil leaks
Tighten bolts and nuts steering linkage and gear box, axle/suspension parts, propeller and exhaust system
Check brake and clutch lines, and oil/fluid reservoirs for leaks
Remove front suspension spacer blocks (if applicable)
Check body mounting torque (if applicable)

MA-6
GENERAL MAINTENANCE

GENERAL MAINTENANCEPFP:00000
General MaintenanceELS000AL
General maintenance includes those items which should be checked during the normal day-to-day operation
of the vehicle. They are essential if the vehicle is to continue operating properly. The owners can perform the
checks and inspections themselves or they can have their NISSAN dealers do them for a nominal charge.
OUTSIDE THE VEHICLE
The maintenance items listed here should be performed from time to time, unless otherwise specified.
INSIDE THE VEHICLE
The maintenance items listed here should be checked on a regular basis, such as when performing periodic maintenance, cleaning the
vehicle, etc.
UNDER THE HOOD AND VEHICLE
The maintenance items listed here should be checked periodically e.g. each time you check the engine oil or refuel.Item Reference page
TiresCheck the pressure with a gauge periodically when at a service station, includ-
ing the spare, and adjust to the specified pressure if necessary. Check carefully
for damage, cuts or excessive wear.—
Windshield wiper
bladesCheck for cracks or wear if not functioning correctly. —
Doors and engine
hoodCheck that all doors, the engine hood, the trunk lid and back door operate prop-
erly. Also ensure that all latches lock securely. Lubricate if necessary. Make sure
that the secondary latch keeps the hood from opening when the primary latch is
released.
When driving in areas using road salt or other corrosive materials, check for
lubrication frequently.BL-12
, BL-18
Tire rotationTires should be rotated every 5,000 km (3,000 miles).MA-41
Item Reference page
LampsMake sure that the headlamps, stop lamps, tail lamps, turn signal lamps, and
other lamps are all operating properly and installed securely. Also check head-
lamp aim.—
Warning lamps and
chimesMake sure that all warning lamps and buzzers/chimes are operating properly. —
Steering wheelCheck that it has the specified play.
Check for changes in the steering conditions, such as excessive free play, hard
steering or strange noises.
Free play: Less than 35 mm (1.38 in)—
Seat beltsCheck that all parts of the seat belt system (e.g. buckles, anchors, adjusters and
retractors) operate properly and smoothly, and are installed securely. Check the
belt webbing for cuts, fraying, wear or damage.MA-45
Item Reference page
Windshield washer
fluidCheck that there is adequate fluid in the tank. —
Engine coolant levelCheck the coolant level when the engine is cold.MA-20
(QR20DE,
QR25DE)
MA-28
(YD22DDTi)
Engine oil levelCheck the level after parking the vehicle on a level spot and turning off the
engine.MA-23
(QR20DE,
QR25DE)
MA-33
(YD22DDTi)
Brake and clutch fluid
levelsMake sure that the brake and clutch fluid levels are between the “MAX” and
“MIN” lines on the reservoir.MA-37
, MA-41
BatteryCheck the fluid level in each cell. It should be between the “MAX” and “MIN”
lines.—

WW-8
FRONT WIPER AND WASHER SYSTEM

Terminal and Reference Values for Combination SwitchEKS0032P
Removal and Installation for Front Wiper Arms, Adjustment for Wiper Arms
Stop Location
EKS0032Q
1. Prior to front wiper arm installation, turn on wiper switch to oper-
ate front wiper motor and then turn it “OFF” (Auto Stop).
2. Lift the blade up and then set it down onto glass surface to set
the blade center to clearance “L1” & “L2” immediately before
tightening nut.
3. Eject washer fluid. Turn on front wiper switch to operate front
wiper motor and then turn it “OFF”.
4. Ensure that front wiper blades stop within clearance “L1” & “L2”.

Tighten front wiper arm nuts to specified torque.

Before reinstalling front wiper arm, clean up the pivot area as
illustrated. This will reduce possibility of front wiper arm loose-
ness.
TERMINAL
NO.WIRE
COLORITEM CONDITION
DATA (DC Voltage)
IGNITION
SWITCHCONDITION OR OPERATION
13 L/YWiper auto
Stop signalONWiper is moving Approx. 0V
Wiper while the vehicle is stopped Battery voltage
14 LWiper motor
Operation signal (LO)ON Wiper switchOFF Battery voltage
LO Approx. 0V
15 Y/G Ignition ON signal ON — Battery voltage
16 L/BWiper motor
Operation signal (HI)ON Wiper switchOFF Battery voltage
HI Approx. 0V
17 B/W Ground OFF — —
18 G Washer switch signal ON Wiper switchWASH Approx. 0V
OFF Battery voltage
PKIA5548E
Clearance “L1”: 49.2 - 64.2 mm (1.937 - 2.528 in)
Clearance “L2”: 39.3 - 54.3 mm (1.547 - 2.138 in)
Front wiper:
23.6 N-m (2.4 kg-m, 17 ft-lb)
PKIA5763E
SEL024J

WW-16
REAR WIPER AND WASHER SYSTEM

Terminal and Reference Values for Combination SwitchEKS00330
Removal and Installation for Rear Wiper Arms EKS00331
WIPER ARMS
1. Turn on wiper switch to operate wiper motor and then turn it
“OFF” (Auto Stop).
2. Lift the blade up and then set it down onto glass surface. Set the
black center to clearance “L” immediately before tightening the
nut.
3. Eject washer fluid. Turn on wiper switch to operate wiper motor
and then turn it “OFF”.
4. Ensure that wiper blades stop on the lowest heat wire.

Center to clearance "L".

Tighten rear wiper arm nuts to specified torque.

Before reinstalling wiper arm, clean up the pivot area as
illustrated. This will reduce possibility of wiper arm
looseness.
TERMINAL
NO.WIRE
COLORITEM CONDITION
DATA(DC Voltage)
IGNITION
SWITCHCONDITION OR OPERATION
21 WWiper motor
Operation signal
(ON)ON Wiper switchOFF Battery voltage
ON Approx. 0V
22 LG/BWasher switch sig-
nalON Wiper switchWASH Approx. 0V
OFF Battery voltage
23 BR/YWiper motor
Operation signalON Wiper switch: INT
24 B/W Ground OFF — —
SKIA0083J
"L" : 63.1±7.5 mm (2.484±0.295 in)
: 15.2 N-m (1.5 kg-m, 11 ft-lb)SKIA0077E
SEL024J

IDX-7
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
Park/neutral position switch (A/T) .................... AT-100
Park/neutral position switch (M/T) ..................... MT-13
PCV (positive crankcase ventilation) . EC-478, EC-870
PGC/V - Wiring diagram .................................. EC-267
PHASE - Wiring diagram ................... EC-255, EC-648
Pilot bushing replacement - See Pilot
converter(QR20DEQR25DE) ........................... EM-82
Piston assembly(QR20DEQR25DE) .............. EM-103
Piston pin inspection(QR20DEQR25DE) ......... EM-99
Piston pin inspection(YD22DDTi) .................... EM-222
Piston ring inspection(QR20DEQR25DE) ...... EM-100
Piston ring inspection(YD22DDTi) ................... EM-227
Piston to bore clearance(QR20DEQR25DE) . EM-103
Piston to bore clearance(YD22DDTi) .............. EM-230
PNP/SW - Wiring diagram EC-375, EC-727, EC-1183,
EC-1480
PNPSW1 - Wiring diagram .............................. EC-817
POS - Wiring diagram ........................ EC-248, EC-640
POWER - Wiring diagram .................................... PG-3
Power antenna .................................................. AV-41
Power door lock .................................................. BL-22
Power seat ......................................................... SE-10
Power socket ................................................... WW-29
Power steering fluid level ......................... PS-6, MA-44
Power steering gear .......................................... PS-13
Power steering oil pressure switch EC-1186, EC-1483
Power steering oil pump .................................... PS-24
Power steering pressure (PSP) sensor .......... EC-274,
EC-656
Power supply routing ........................................... PG-2
Power window .................................................. GW-40
Precations for Leak detection dye ................... ATC-12
Precautions (General) .......................................... GI-4
Pre-delivery inspection ........................................ MA-4
Pressure plate - See Clutch cover ..................... CL-14
PRGVLV - Wirng diagram ............................... EC-810
Propeller shaft ..................................................... PR-3
Propeller shaft on vehicle service ........................ PR-3
PS/SEN - Wiring diagram .................. EC-275, EC-657
PST/SW - Wiring diagram ............. EC-1187, EC-1484
Q
Quick-glow system ........................ EC-1169
, EC-1457
R
R/FOG - Wiring diagram ..................................... LT-56
Radiator(QR20DEQR25DE) ................ CO-12, CO-14
Radiator(YD22DDTi) ............................ CO-34, CO-38
Radio - See Audio ............................................... AV-4
Rear air spoiler .................................................... EI-30
Rear bumper ........................................................ EI-17
Rear disc brake ................................................. BR-32
Rear door ............................................................ BL-18
Rear fog lamp ..................................................... LT-56
Rear panel finisher .............................................. EI-31
Rear seat ........................................................... SE-31
Rear seat belt ...................................................... SB-4
Rear side window ............................................. GW-13
Rear suspension ............................................... RSU-5
Rear washer .................................................... WW-14
Rear window defogger ...................................... GW-17
Rear wiper ....................................................... WW-14
Refrigerant connection precaution ..................... ATC-5
Refrigerant discharging evacuating charging ATC-141
Refrigerant general precaution .......................... ATC-5
Refrigerant lines ............................................. ATC-141
Refrigerant pressure sensor EC-451, EC-843, ATC-18,
ATC-94
, ATC-157
Refrigeration cycle ........................................... ATC-18
Release bearing (clutch) .................................... CL-12
Removal and installation (A/T) ......................... AT-413
Removal and installation (Transfer) ................... TF-55
Reverse idler shaft (M/T) ...................... MT-20, MT-25
Reverse lamp switch (M/T) - See Back-up lamp switch
(M/T) .................................................................. MT-13
Reverse main gear (M/T) ...................... MT-20, MT-25
Rocker cover(QR20DEQR25DE) .................... EM-42
Rocker cover(YD22DDTi) ............................... EM-168
Room lamp ......................................................... LT-76
Room lamp - See Interior lamp ........................... LT-76
ROOM/L - Wiring diagram .................................. LT-76
RP/SEN - Wiring diagram .................. EC-452, EC-844
RRO2 - Wiring diagram ..................... EC-777, EC-793
S
S/LOCK - Wiring diagram ....................... BL-24
, BL-45
S/SIG - Wiring diagram .................. EC-1199, EC-1496
SCTC/V - Wiring diagram ............. EC-1095, EC-1129,
EC-1136
, EC-1141, EC-1146, EC-1384, EC-1418,
EC-1424
, EC-1429, EC-1434
SEAT - Wiring diagram ...................................... SE-11
Seat belt inspection .......................................... MA-45
Seat belt pre-tensioner disposal ..................... SRS-42
Seat belt, front ..................................................... SB-3
Seat belt, rear ...................................................... SB-4
Seat, front .......................................................... SE-24
Seat, rear ........................................................... SE-31
Self-diagnosis (Transfer) ................................... TF-30
SEN/PW - Wiring diagram ................. EC-369, EC-721
Sheft warning system ...................................... BL-104
SHIFT - Wiring diagram ................................... AT-399
Shift control components (M/T) ............. MT-22, MT-27
Shift fork (M/T) ...................................... MT-22, MT-27
Shift lever ........................................................... MT-14
Shift lock system .............................................. AT-398
Shift schedule .................................................. AT-530
Shift solenoid valve A (A/T) ............................. AT-128
Shift solenoid valve B (A/T) ............................. AT-128
Side air bag (satellite) sensor ......................... SRS-39
Side window - See Rear side window ............... GW-13
Spark plug replacement(QR20DEQR25DE) ... MA-26
Spark plug(QR20DEQR25DE) ........................ EM-30
Specification value ............................. EC-119, EC-566
Speedometer ........................................................ DI-4
Spiral cable ..................................................... SRS-33