2003 NISSAN X-TRAIL rear bumper

EI-18
REAR BUMPER

6. Remove rear fog lamp connectors. Pull bumper fascia assembly straight rearward to remove.
7. Remove mounting bolts on bumper stay.
8. Remove rear bumper finisher, or rear fog lamps, and the reflectors from bumper.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
After installation, adjust the clearance.

SQUEAK AND RATTLE TROUBLE DIAGNOSES
IP-7
C
D
E
F
G
H
J
K
L
MA
B
IP

TRUNK
Trunk noises are often caused by a loose jack or loose items put into the trunk by the owner.
In addition look for:
1. Trunk lid dumpers out of adjustment
2. Trunk lid striker out of adjustment
3. Trunk lid torsion bars knocking together
4. A loose license plate or bracket
Most of these incidents can be repaired by adjusting, securing or insulating the item(s) or component(s) caus-
ing the noise.
SUNROOF/HEADLINING
Noises in the sunroof/headlining area can often be traced to one of the following:
1. Sunroof lid, rail, linkage or seals making a rattle or light knocking noise
2. Sunvisor shaft shaking in the holder
3. Front or rear windshield touching headlining and squeaking
Again, pressing on the components to stop the noise while duplicating the conditions can isolate most of these
incidents. Repairs usually consist of insulating with felt cloth tape.
SEATS
When isolating seat noise it's important to note the position the seat is in and the load placed on the seat when
the noise is present. These conditions should be duplicated when verifying and isolating the cause of the
noise.
Cause of seat noise include:
1. Headrest rods and holder
2. A squeak between the seat pad cushion and frame
3. Rear seat back lock and bracket
These noises can be isolated by moving or pressing on the suspected components while duplicating the con-
ditions under which the noise occurs. Most of these incidents can be repaired by repositioning the component
or applying urethane tape to the contact area.
UNDERHOOD
Some interior noise may be caused by components under the hood or on the engine wall. The noise is then
transmitted into the passenger compartment.
Causes of transmitted underhood noise include:
1. Any component mounted to the engine wall
2. Components that pass through the engine wall
3. Engine wall mounts and connectors
4. Loose radiator mounting pins
5. Hood bumpers out of adjustment
6. Hood striker out of adjustment
These noise can be difficult to isolate since they cannot be reached from the interior of the vehicle. The best
method is to secure, move or insulate one component at a time and test drive the vehicle. Also, engine RPM
or load can be changed to isolate the noise. Repairs can usually be made by moving, adjusting securing, or
insulating the component causing the noise.

SQUEAK AND RATTLE TROUBLE DIAGNOSES
SE-7
C
D
E
F
G
H
J
K
L
MA
B
SE

TRUNK
Trunk noises are often caused by a loose jack or loose items put into the trunk by the owner.
In addition look for:
1. Trunk lid dumpers out of adjustment
2. Trunk lid striker out of adjustment
3. Trunk lid torsion bars knocking together
4. A loose license plate or bracket
Most of these incidents can be repaired by adjusting, securing or insulating the item(s) or component(s) caus-
ing the noise.
SUNROOF/HEADLINING
Noises in the sunroof/headlining area can often be traced to one of the following:
1. Sunroof lid, rail, linkage or seals making a rattle or light knocking noise
2. Sunvisor shaft shaking in the holder
3. Front or rear windshield touching headlining and squeaking
Again, pressing on the components to stop the noise while duplicating the conditions can isolate most of these
incidents. Repairs usually consist of insulating with felt cloth tape.
SEATS
When isolating seat noise it's important to note the position the seat is in and the load placed on the seat when
the noise is present. These conditions should be duplicated when verifying and isolating the cause of the
noise.
Cause of seat noise include:
1. Headrest rods and holder
2. A squeak between the seat pad cushion and frame
3. Rear seat back lock and bracket
These noises can be isolated by moving or pressing on the suspected components while duplicating the con-
ditions under which the noise occurs. Most of these incidents can be repaired by repositioning the component
or applying urethane tape to the contact area.
UNDERHOOD
Some interior noise may be caused by components under the hood or on the engine wall. The noise is then
transmitted into the passenger compartment.
Causes of transmitted underhood noise include:
1. Any component mounted to the engine wall
2. Components that pass through the engine wall
3. Engine wall mounts and connectors
4. Loose radiator mounting pins
5. Hood bumpers out of adjustment
6. Hood striker out of adjustment
These noise can be difficult to isolate since they cannot be reached from the interior of the vehicle. The best
method is to secure, move or insulate one component at a time and test drive the vehicle. Also, engine RPM
or load can be changed to isolate the noise. Repairs can usually be made by moving, adjusting securing, or
insulating the component causing the noise.

CHASSIS AND BODY MAINTENANCE
MA-45
C
D
E
F
G
H
I
J
K
MA
B
MA

Drive ShaftELS000CL

Check boot and drive shaft for cracks, wear, damage and
grease leakage.
Lubricating Locks, Hinges and Hood LatchesELS000BR
Checking Seat Belts, Buckles, Retractors, Anchors and AdjustersELS000BS
Checking Body CorrosionELS000C0
Visually check body panels for collision damage (scratches, chipping, rubbing, etc.) or damage to the anti-cor-
rosion materials. In particular, check the following locations.
HEMMED PANELS
Hood front end, door lower end, trunk lid rear end, etc.
PA N E L J O I N T
Side sill of rear fender and center pillar, rear wheel housing of rear fender, around strut tower in engine com-
partment, etc.
PA N E L E D G E
Trunk lid opening, sunroof opening, fender wheel-arch flange, fuel filler lid flange, around holes in panel, etc.
PARTS CONTACT
Waist moulding, windshield moulding, bumper, etc.
SFA108A
Front door Refer to BL-18, "DOOR" .
Back door Refer to BL-99, "
BACK DOOR" .

REAR FOG LAMP
LT-59
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb ReplacementEKS0015L
1. Remove rear fog lamp. Refer to LT- 5 9 , "Removal and Installa-
tion" .
2. Turn bulb socket counterclockwise and unlock it.
3. Remove bulb.
Removal and InstallationEKS0015M
REMOVAL
1. Remove rear fog lamp mounting screws (2).
2. Take out rear fog lamp from bumper, then disconnect connector.
INSTALLATION
Install in the reverse order of removal, paying attention to the following.Rear fog lamp : 12V 21W
SKIA0052E
SKIA0090E
Rear fog lamp mounting screws
Tightening torque : 1.4 N·m (0.14 kg-m, 12 in-lb)

IDX-3
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
Blower unit ....................... ATC-125, MTC-22, MTC-24
BOOST - Wiring diagram ............... EC-1040, EC-1347
Boring/horning cylinder block(QR20DEQR25DE) .......
EM-103
Brake booster .................................................... BR-23
Brake fluid change ............................................... BR-8
Brake fluid level ................................................. MA-41
Brake fluid level and line check ........................... BR-8
Brake hydraulic line ........................................... BR-10
Brake inspection ................................................ MA-43
Brake lines and cables inspection ..................... MA-41
Brake master cylinder ........................................ BR-14
Brake pedal ......................................................... BR-6
Brake switch ..... EC-380, EC-733, EC-1177, EC-1475
BRK/SW - Wiring diagram EC-381, EC-735, EC-1178,
EC-1476
Bulb specifications .............................................. LT-92
Bumper, front ....................................................... EI-14
Bumper, rear ........................................................ EI-17
C
Camshaft inspection(QR20DEQR25DE) .......... EM-55
Camshaft inspection(YD22DDTi) .................... EM-171
Camshaft position sensor (CMPS) EC-1056, EC-1062,
EC-1363
, EC-1369
Camshaft position sensor (PHASE) .. EC-254, EC-646
Camshaft(QR20DEQR25DE) ........................... EM-53
Camshaft(YD22DDTi) ...................................... EM-170
CAN - Wiring diagram ......... EC-133, EC-580, EC-945,
EC-1269
, LAN-10, LAN-26, LAN-51, LAN-69, LAN-87
CAN (Controller Area Network) ........... BRC-8, LAN-9,
LAN-25
, LAN-50, LAN-68, LAN-86
CAN communication EC-38, EC-132, EC-500, EC-579,
EC-888
, EC-944, EC-1268, AT-32, AT-97, AT-329,
TF-43
, BRC-8, LAN-9, LAN-25, LAN-50, LAN-68,
LAN-86
Canister-See EVAP canister ............. EC-476, EC-868
CHARGE - Wiring diagram .................... SC-13, SC-14
Charging system ................................................ SC-12
Chassis and body maintenance ........................ MA-37
CHIME - Wiring diagram ................ DI-52, DI-55, DI-56
CIGAR - Wiring diagram .................................. WW-27
Cigarette lighter ............................................... WW-27
Circuit breaker ................................................... PG-12
CKPS - Wiring diagram .. EC-947, EC-1046, EC-1052,
EC-1271
, EC-1353, EC-1359
Clearance lamp ........................................ LT-4, LT-60
Clock ................................................................... DI-61
CLOCK - Wiring diagram .................................... DI-61
Closed loop control .............................. EC-35, EC-497
Clutch cover ....................................................... CL-14
Clutch disc ......................................................... CL-14
Clutch master cylinder ......................................... CL-8
Clutch operating cylinder ................................... CL-10
Clutch pedal ......................................................... CL-5
Clutch release bearing ....................................... CL-12
Clutch release mechanism ................................ CL-12
Clutch withdrawal lever ...................................... CL-12
CMPS - Wiring diagram . EC-947, EC-1058, EC-1064,
EC-1271
, EC-1365, EC-1371
Coil spring (rear) ............................................... RSU-8
Collision diagnosis .......................................... SRS-48
Combination meter ............................................... DI-4
Combination switch ............................................. LT-40
Component Location (auto A/C) ......... ATC-35, MTC-4
Compression pressure(QR20DEQR25DE) ..... EM-67
Compression pressure(YD22DDTi) ................ EM-196
Compressor clutch removal and installation .. ATC-146
Compressor special service tool ...................... ATC-14
Condenser ..................................................... ATC-155
Connecting rod bearing clearance(QR20DEQR25DE)
EM-101
Connecting rod bearing clearance(YD22DDTi) EM-232
Connecting rod bushing clearance(YD22DDTi) EM-226
Connecting rod(QR20DEQR25DE) ............... EM-101
Connecting rod(YD22DDTi) .............. EM-223, EM-228
CONSULT for engine ......................... EC-102, EC-551
CONSULT-II for engine ................... EC-926, EC-1251
Control lever (M/T) ............................................. MT-14
Control unit ..................................... ATC-120, MTC-21
Control units (terminal arrangement) ................. PG-72
Controller Area Network (CAN) ........... BRC-8, LAN-9,
LAN-25
, LAN-50, LAN-68, LAN-86
Converter housing installation ......................... AT-523
COOL/F - Wiring diagram EC-352, EC-704, EC-1014,
EC-1322
Coolant replacement(QR20DEQR25DE) ........ MA-20
Coolant replacement(YD22DDTi) ..................... MA-28
Cooling circuit (engine)(QR20DEQR25DE) ....... CO-7
Cooling circuit (engine)(YD22DDTi) ................. CO-29
Cooling fan ............................................ CO-18, CO-36
Cooling fan relay EC-363, EC-715, EC-1024, EC-1331
Coupling sleeve (M/T) ........................... MT-20, MT-25
Cowl top .............................................................. EI-20
Cowl top cover .................................................... EI-20
Crankcase ventilation system .......... EC-888, EC-1219
Crankcase ventilation system - See Positive crankcase
ventilation ........................................... EC-478
, EC-870
Crankshaft position sensor (POS) ..... EC-247, EC-638
Crankshaft position sensor (TDC) EC-1044, EC-1050,
EC-1351
, EC-1357
Crankshaft(QR20DEQR25DE) ........................ EM-83
Cylinder block boring(QR20DEQR25DE) ...... EM-104
Cylinder block boring(YD22DDTi) ................... EM-230
Cylinder block(QR20DEQR25DE) ................... EM-82
Cylinder block(YD22DDTi) .............................. EM-212
Cylinder head bolt tightening(QR20DEQR25DE) ........
EM-69
Cylinder head bolt tightening(YD22DDTi) ....... EM-198
Cylinder head gasket selection(YD22DDTi) ... EM-199
Cylinder head(QR20DEQR25DE) ................... EM-67
Cylinder head(YD22DDTi) .............................. EM-196
D
Data link connector ............................ EC-469
, EC-861
Data link connector for Consult ......... EC-104, EC-553,

IDX-4
ALPHABETICAL INDEX
EC-926, EC-1251
Daytime light system ........................................... LT-20
Daytime running light - See Daytime light system LT-20
DEF - Wiring diagram ....................................... GW-21
Desiccant Assembly ...................................... ATC-156
Diagnosis sensor unit ..................................... SRS-41
Diagnostic trouble code (DTC) ...................... EC-1223
Diagnostic trouble code (DTC) for OBD system EC-19,
EC-54
, EC-482, EC-513, EC-874, EC-894, EC-1205
Diagnostic trouble code (DTC) inspection priority chart
EC-76
, EC-523, EC-904, EC-1230
Differential gear (FF M/T) ..................... MT-23, MT-28
DLC - Wiring diagram ........................ EC-469, EC-861
Door glass ........................................... GW-80, GW-83
Door glass Fitting Adjustment ............. GW-80, GW-83
Door lock ................................................. BL-91, BL-95
Door mirror ........................................................ GW-86
Door trim ............................................................. EI-32
Door, front .......................................................... BL-18
Door, rear ........................................................... BL-18
Drive belt inspection(QR20DEQR25DE) ......... MA-20
Drive belt inspection(YD22DDTi) ...................... MA-27
Drive belt(QR20DEQR25DE) .......................... EM-13
Drive belt(YD22DDTi) ..................................... EM-131
Drive shaft (front) ............................................. FAX-11
Drive shaft (rear) ............................................. RAX-10
Driver air bag .................................................. SRS-30
Dropping resistor (A/T) ...................... AT-160, AT-393
DTC work support ............................................ EC-111
DTRL - Wiring diagram ....................................... LT-20
Dual pressure switch ........ ATC-18, ATC-95, ATC-158
Duct and grilles ............................... ATC-137, MTC-33
E
ECM input/output signal ....................... EC-95
, EC-543
ECM power supply EC-124, EC-282, EC-571, EC-664,
EC-937
, EC-1261
ECM relay ...................................... EC-1110, EC-1399
ECM/PW - Wiring diagram ................. EC-283, EC-665
ECTS - Wiring diagram ...... EC-164, EC-599, EC-983,
EC-1293
EGR function ................ EC-1073, EC-1080, EC-1465
EGR volume control valve ............ EC-1073, EC-1080,
EC-1465
EGRC/V - Wiring diagram ............. EC-1076, EC-1083,
EC-1467
Electric sunroof .................................................. RF-10
Electric throttle control actuator ........ EC-290, EC-292,
EC-310
, EC-668, EC-671, EC-690
Electrical load signal circuit ................ EC-456, EC-848
Electrical unit ..................................................... PG-72
Electrical units location ...................................... PG-65
Electronic ignition (EI) system ............. EC-37, EC-499
Engine control circuit diagram EC-93, EC-541, EC-917,
EC-1243
Engine control component parts location .......... EC-88,
EC-536
Engine control module (ECM) ........... EC-279, EC-661, EC-1089
, EC-1091, EC-1378, EC-1380
Engine control system diagram and chart ........ EC-30,
EC-492
, EC-883, EC-1214
Engine coolant temperature sensor (ECTS) ... EC-162,
EC-597
, EC-981, EC-1291
Engine coolant(QR20DEQR25DE) .................... CO-9
Engine coolant(YD22DDTi) .............................. CO-31
Engine fail-safe system ....................... EC-77, EC-524
Engine oil filter replacement(QR20DEQR25DE) .........
MA-25
Engine oil filter replacement(YD22DDTi) MA-33, MA-35
Engine oil precautions .......................................... GI-7
Engine oil replacement(QR20DEQR25DE) ..... MA-23
Engine oil replacement(YD22DDTi) .................. MA-33
Engine oil(QR20DEQR25DE) ............................. LU-7
Engine oil(YD22DDTi) ....................................... LU-20
Engine removal(QR20DEQR25DE) ................ EM-78
Engine removal(YD22DDTi) ........................... EM-208
ETC1 - Wiring diagram ..................... EC-293, EC-673
ETC2 - Wiring diagram ..................... EC-304, EC-684
ETC3 - Wiring diagram ..................... EC-311, EC-691
EVAP canister purge volume control solenoid valve ....
EC-265
, EC-473, EC-809, EC-865
EVAP vapor lines inspection(QR20DEQR25DE) ........
MA-26
Evaporative emission (EVAP) system EC-473, EC-865
Evaporator .................................................... ATC-158
Exhaust manifold(QR20DEQR25DE) .............. EM-23
Exhaust manifold(YD22DDTi) ......................... EM-141
Exhaust system ................................................... EX-2
Exhaust system inspection ..................... EX-2, MA-37
Expansion valve ............................................ ATC-159
Exterior EI-21, EI-22, EI-24, EI-25, EI-26, EI-27, EI-28,
EI-30
, EI-31
F
F/FOG - Wiring diagram ......................... LT-52
, LT-53
F/PUMP - Wiring diagram EC-444, EC-836, EC-1134,
EC-1422
Fan control amp. ............................. ATC-84, ATC-129
Fan switch ....................................................... MTC-18
FIAR - Wiring diagram .................. EC-1117, EC-1406
Final drive (FF M/T) .............................. MT-23, MT-28
Finisher, interior - See Trim ................................ EI-32
Finisher, rear panel ............................................. EI-31
Floor trim ............................................................. EI-38
Flow charts ......................................................... GI-23
Fluid temperature sensor (A/T) ........................ AT-111
Fluorescent leak detector ............................. ATC-160
Flywheel (clutch) ................................................ CL-14
Flywheel runout(QR20DEQR25DE) EM-108, EM-235
Fog lamp, front ................................................... LT-52
Fork rod (M/T) ....................................... MT-22, MT-27
Freeze frame data EC-55, EC-514, EC-895, EC-1223
FRO2 - Wiring diagram ..................... EC-772, EC-787
Front bumper ...................................................... EI-14
Front disc brake ................................................. BR-27
Front door .......................................................... BL-18

IDX-7
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
Park/neutral position switch (A/T) .................... AT-100
Park/neutral position switch (M/T) ..................... MT-13
PCV (positive crankcase ventilation) . EC-478, EC-870
PGC/V - Wiring diagram .................................. EC-267
PHASE - Wiring diagram ................... EC-255, EC-648
Pilot bushing replacement - See Pilot
converter(QR20DEQR25DE) ........................... EM-82
Piston assembly(QR20DEQR25DE) .............. EM-103
Piston pin inspection(QR20DEQR25DE) ......... EM-99
Piston pin inspection(YD22DDTi) .................... EM-222
Piston ring inspection(QR20DEQR25DE) ...... EM-100
Piston ring inspection(YD22DDTi) ................... EM-227
Piston to bore clearance(QR20DEQR25DE) . EM-103
Piston to bore clearance(YD22DDTi) .............. EM-230
PNP/SW - Wiring diagram EC-375, EC-727, EC-1183,
EC-1480
PNPSW1 - Wiring diagram .............................. EC-817
POS - Wiring diagram ........................ EC-248, EC-640
POWER - Wiring diagram .................................... PG-3
Power antenna .................................................. AV-41
Power door lock .................................................. BL-22
Power seat ......................................................... SE-10
Power socket ................................................... WW-29
Power steering fluid level ......................... PS-6, MA-44
Power steering gear .......................................... PS-13
Power steering oil pressure switch EC-1186, EC-1483
Power steering oil pump .................................... PS-24
Power steering pressure (PSP) sensor .......... EC-274,
EC-656
Power supply routing ........................................... PG-2
Power window .................................................. GW-40
Precations for Leak detection dye ................... ATC-12
Precautions (General) .......................................... GI-4
Pre-delivery inspection ........................................ MA-4
Pressure plate - See Clutch cover ..................... CL-14
PRGVLV - Wirng diagram ............................... EC-810
Propeller shaft ..................................................... PR-3
Propeller shaft on vehicle service ........................ PR-3
PS/SEN - Wiring diagram .................. EC-275, EC-657
PST/SW - Wiring diagram ............. EC-1187, EC-1484
Q
Quick-glow system ........................ EC-1169
, EC-1457
R
R/FOG - Wiring diagram ..................................... LT-56
Radiator(QR20DEQR25DE) ................ CO-12, CO-14
Radiator(YD22DDTi) ............................ CO-34, CO-38
Radio - See Audio ............................................... AV-4
Rear air spoiler .................................................... EI-30
Rear bumper ........................................................ EI-17
Rear disc brake ................................................. BR-32
Rear door ............................................................ BL-18
Rear fog lamp ..................................................... LT-56
Rear panel finisher .............................................. EI-31
Rear seat ........................................................... SE-31
Rear seat belt ...................................................... SB-4
Rear side window ............................................. GW-13
Rear suspension ............................................... RSU-5
Rear washer .................................................... WW-14
Rear window defogger ...................................... GW-17
Rear wiper ....................................................... WW-14
Refrigerant connection precaution ..................... ATC-5
Refrigerant discharging evacuating charging ATC-141
Refrigerant general precaution .......................... ATC-5
Refrigerant lines ............................................. ATC-141
Refrigerant pressure sensor EC-451, EC-843, ATC-18,
ATC-94
, ATC-157
Refrigeration cycle ........................................... ATC-18
Release bearing (clutch) .................................... CL-12
Removal and installation (A/T) ......................... AT-413
Removal and installation (Transfer) ................... TF-55
Reverse idler shaft (M/T) ...................... MT-20, MT-25
Reverse lamp switch (M/T) - See Back-up lamp switch
(M/T) .................................................................. MT-13
Reverse main gear (M/T) ...................... MT-20, MT-25
Rocker cover(QR20DEQR25DE) .................... EM-42
Rocker cover(YD22DDTi) ............................... EM-168
Room lamp ......................................................... LT-76
Room lamp - See Interior lamp ........................... LT-76
ROOM/L - Wiring diagram .................................. LT-76
RP/SEN - Wiring diagram .................. EC-452, EC-844
RRO2 - Wiring diagram ..................... EC-777, EC-793
S
S/LOCK - Wiring diagram ....................... BL-24
, BL-45
S/SIG - Wiring diagram .................. EC-1199, EC-1496
SCTC/V - Wiring diagram ............. EC-1095, EC-1129,
EC-1136
, EC-1141, EC-1146, EC-1384, EC-1418,
EC-1424
, EC-1429, EC-1434
SEAT - Wiring diagram ...................................... SE-11
Seat belt inspection .......................................... MA-45
Seat belt pre-tensioner disposal ..................... SRS-42
Seat belt, front ..................................................... SB-3
Seat belt, rear ...................................................... SB-4
Seat, front .......................................................... SE-24
Seat, rear ........................................................... SE-31
Self-diagnosis (Transfer) ................................... TF-30
SEN/PW - Wiring diagram ................. EC-369, EC-721
Sheft warning system ...................................... BL-104
SHIFT - Wiring diagram ................................... AT-399
Shift control components (M/T) ............. MT-22, MT-27
Shift fork (M/T) ...................................... MT-22, MT-27
Shift lever ........................................................... MT-14
Shift lock system .............................................. AT-398
Shift schedule .................................................. AT-530
Shift solenoid valve A (A/T) ............................. AT-128
Shift solenoid valve B (A/T) ............................. AT-128
Side air bag (satellite) sensor ......................... SRS-39
Side window - See Rear side window ............... GW-13
Spark plug replacement(QR20DEQR25DE) ... MA-26
Spark plug(QR20DEQR25DE) ........................ EM-30
Specification value ............................. EC-119, EC-566
Speedometer ........................................................ DI-4
Spiral cable ..................................................... SRS-33