2003 NISSAN X-TRAIL check engine

COMBINATION METERS (RHD MODELS)
DI-37
C
D
E
F
G
H
I
J
L
MA
B
DI
Low Fuel Warning Lamp Illuminate or Not IlluminateEKS0030X
1.DIAGNOSIS MODE INSPECTION
Preform combination meter diagnosis mode. Refer toDI-28, "
Meter/Gauge Operation and Odo/Trip Meter
Segment Check in Diagnosis Mode".
OK or NG
OK >> Check fuel level sensor unit or sub fuel level sensor unit. Refer toDI-37, "Electrical Components
Inspection".
NG >> Replace combination meter.
Electrical Components InspectionEKS0031V
FUEL LEVEL SENSOR UNIT CHECK / GASOLINE ENGINE MODELS
For removal, refer toFL-4, "FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY"for
Gasoline engine models.
Fuel level sensor unit
Check the resistance between terminals 1 and 4.
*1 and *2: When float rod is in contact with stopper.
Sub fuel level sensor unit
Check the resistance between terminals 3 and 1.
*1 and *2: When float rod is in contact with stopper.
FUEL LEVEL SENSOR UNIT CHECK / DIESEL ENGINE MODELS
For removal, refer toFL-17, "FUEL LEVEL SENSOR UNIT"for Diesel engine models.
Fuel level sensor unit
Check the resistance between terminals 1 and 4.
*1 and *2: When float rod is in contact with stopper.Ohmmeter
Float position mm (in)Resistance
valueW
(+) (-)
41*1 Full 24 (2.36) Approx. 4 - 6
*2 Empty 167 (6.57) Approx.79 - 84
SKIA0904E
Ohmmeter
Float position mm (in)Resistance
valueW
(+) (-)
13*1 Full 35 (1.50) Approx. 0.8 -1
*2 Empty 186 (6.38) Approx.79 - 84
SKIA1032E
Ohmmeter
Float position mm (in)Resistance
valueW
(+) (-)
41*1 Full 24 (2.38) Approx. 4 - 6
23 Empty 170 (6.46) Approx. 79 - 84
SKIA0908E

DI-50
WARNING LAMPS
Electrical Components Inspection
EKS002HK
FUEL WARNING LAMP OPERATION CHECK
1. Turn ignition switch “OFF”.
2. Disconnect fuel level sensor unit harness connector B125.
3. Connect a resistor (80W) between fuel level sensor unit harness
connector terminal 1(G) and ground.
4. Turn ignition switch “ON”.
The fuel warning lamp should come on.
OIL PRESSURE SWITCH CHECK
Check the continuity between the terminals of oil pressure switch
and body ground.
DIODE CHECK
lCheck continuity using an ohmmeter.
lDiode is functioning properly if test results are as shown in the
figure at left.
lCheck diodes at the combination meter harness connector
instead of on the combination meter assembly. Refer toDI-40,
"Wiring Diagram—WARN—/LHDModels"orDI-45, "Wiring
Diagram—WARN—/RHDModels".
NOTE:
Specification may vary depending on the type of tester. Before
performing this inspection, be sure to refer to the instruction
manual for the tester to be used.
SKIA0993E
Oil pressure kPa (bar,
kg/cm2,psi)Continuity
Engine runningMore than 10 - 20 (0.10 -
0.20,0.1-0.2,1-3)No
Engine not runningLess than 10 - 20 (0.10 -
0.20,0.1-0.2,1-3)Ye s
MEL425F
SEL901F

EC-1
ENGINE CONTROL SYSTEM
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION
A
EC
ENGINE CONTROL SYSTEM
QR (WITH EURO-OBD)
INDEX FOR DTC ...................................................... 12
Alphabetical Index .................................................. 12
DTC No. Index ....................................................... 14
PRECAUTIONS ........................................................ 16
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ................................................................ 16
On Board Diagnostic (OBD) System of Engine and
A/T .......................................................................... 16
Precaution .............................................................. 16
Wiring Diagrams and Trouble Diagnosis ................ 19
PREPARATION ......................................................... 20
Special Service Tools ............................................. 20
Commercial Service Tools ...................................... 20
ENGINE CONTROL SYSTEM .................................. 22
System Diagram ..................................................... 22
Vacuum Hose Drawing ........................................... 23
System Chart ......................................................... 24
Multiport Fuel Injection (MFI) System .................... 24
Electronic Ignition (EI) System ............................... 27
Air Conditioning Cut Control ................................... 27
Fuel Cut Control (at No Load and High Engine
Speed) .................................................................... 28
CAN communication .............................................. 28
BASIC SERVICE PROCEDURE .............................. 30
Idle Speed and Ignition Timing Check .................... 30
Throttle Valve Closed Position Learning ................ 31
Accelerator Pedal Released Position Learning ...... 31
Idle Air Volume Learning ........................................ 31
Fuel Pressure Check .............................................. 34
ON BOARD DIAGNOSTIC (OBD) SYSTEM ............ 36
Introduction ............................................................ 36
Two Trip Detection Logic ........................................ 36
Emission-related Diagnostic Information ................ 37
NATS (Nissan Anti-theft System) ........................... 48
Malfunction Indicator (MI) ....................................... 48
OBD System Operation Chart ................................ 51
TROUBLE DIAGNOSIS ............................................ 57
Trouble Diagnosis Introduction ............................... 57DTC Inspection Priority Chart ................................. 61
Fail-safe Chart ........................................................ 62
Basic Inspection ..................................................... 64
Symptom Matrix Chart ............................................ 69
Engine Control Component Parts Location ............ 73
Circuit Diagram ....................................................... 77
ECM Harness Connector Terminal Layout ............. 79
ECM Terminals and Reference Value ..................... 79
CONSULT-II Function ............................................. 86
Generic Scan Tool (GST) Function ......................... 96
CONSULT-II Reference Value in Data Monitor ....... 97
Major Sensor Reference Graph in Data Monitor
Mode .....................................................................100
TROUBLE DIAGNOSIS - SPECIFICATION VALUE. 103
Description ............................................................103
Testing Condition ..................................................103
Inspection Procedure ............................................103
Diagnostic Procedure ...........................................104
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT .......................................................................107
Description ............................................................107
Diagnostic Procedure ...........................................107
POWER SUPPLY CIRCUIT FOR ECM ...................108
Wiring Diagram .....................................................108
ECM Terminals and Reference Value ...................109
Diagnostic Procedure ...........................................109
Component Inspection ..........................................113
DTC U1000 CAN COMMUNICATION LINE ............114
Description ............................................................114
On Board Diagnosis Logic ....................................114
DTC Confirmation Procedure ...............................114
Wiring Diagram .....................................................115
Diagnostic Procedure ...........................................116
DTC P0011 IVT CONTROL .....................................117
Description ............................................................117
CONSULT-II Reference Value in Data Monitor Mode
.117
ECM Terminals and Reference Value ...................117
On Board Diagnosis Logic ....................................118

EC-4
ECM Terminals and Reference Value ...................260
On Board Diagnosis Logic ....................................261
DTC Confirmation Procedure ...............................261
Wiring Diagram .....................................................262
Diagnostic Procedure ...........................................263
Component Inspection ..........................................264
Removal and Installation ......................................265
D T C P 1111 I V T C ON T R OL S OL E N OI D VA LV E . .. ..266
Component Description ........................................266
CONSULT-II Reference Value in Data Monitor Mode
.266
ECM Terminals and Reference Value ...................266
On Board Diagnosis Logic ....................................266
DTC Confirmation Procedure ...............................267
Wiring Diagram .....................................................268
Diagnostic Procedure ...........................................269
Component Inspection ..........................................270
Removal and Installation ......................................270
DTC P1121 ELECTRIC THROTTLE CONTROL
ACTUATOR .............................................................271
Description ............................................................271
On Board Diagnosis Logic ....................................271
DTC Confirmation Procedure ...............................271
Diagnostic Procedure ...........................................272
DTC P1122 ELECTRIC THROTTLE CONTROL
FUNCTION ..............................................................273
Description ............................................................273
ECM Terminals and Reference Value ...................273
On Board Diagnosis Logic ....................................273
DTC Confirmation Procedure ...............................274
Wiring Diagram .....................................................275
Diagnostic Procedure ...........................................276
Component Inspection ..........................................277
DTC P1123 THROTTLE CONTROL MOTOR RELAY.279
Component Description ........................................279
CONSULT-II Reference Value in Data Monitor Mode
.279
ECM Terminals and Reference Value ...................279
On Board Diagnosis Logic ....................................279
DTC Confirmation Procedure ...............................279
Wiring Diagram .....................................................281
Diagnostic Procedure ...........................................282
Component Inspection ..........................................283
DTC P1143 HO2S1 .................................................284
Component Description ........................................284
CONSULT-II Reference Value in Data Monitor Mode
.284
ECM Terminals and Reference Value ...................284
On Board Diagnosis Logic ....................................285
DTC Confirmation Procedure ...............................285
Overall Function Check ........................................286
Diagnostic Procedure ...........................................286
Component Inspection ..........................................288
Removal and Installation ......................................289
DTC P1144 HO2S1 .................................................290
Component Description ........................................290
CONSULT-II Reference Value in Data Monitor Mode
.290ECM Terminals and Reference Value ................... 290
On Board Diagnosis Logic .................................... 291
DTC Confirmation Procedure ................................ 291
Overall Function Check ......................................... 292
Diagnostic Procedure ............................................ 292
Component Inspection .......................................... 294
Removal and Installation ....................................... 295
DTC P1146 HO2S2 .................................................. 296
Component Description ........................................ 296
CONSULT-II Reference Value in Data Monitor Mode
. 296
ECM Terminals and Reference Value ................... 296
On Board Diagnosis Logic .................................... 296
DTC Confirmation Procedure ................................ 297
Overall Function Check ......................................... 298
Wiring Diagram ..................................................... 299
Diagnostic Procedure ............................................ 300
Component Inspection .......................................... 301
Removal and Installation ....................................... 302
DTC P1147 HO2S2 .................................................. 303
Component Description ........................................ 303
CONSULT-II Reference Value in Data Monitor Mode
. 303
ECM Terminals and Reference Value ................... 303
On Board Diagnosis Logic .................................... 303
DTC Confirmation Procedure ................................ 304
Overall Function Check ......................................... 305
Wiring Diagram ..................................................... 306
Diagnostic Procedure ............................................ 307
Component Inspection .......................................... 308
Removal and Installation ....................................... 309
DTC P1212 ESP/TCS/ABS COMMUNICATION
LINE ......................................................................... 310
Description ............................................................ 310
On Board Diagnosis Logic .................................... 310
DTC Confirmation Procedure ................................ 310
Diagnostic Procedure ............................................ 310
DTC P1217 ENGINE OVER TEMPERATURE ........311
System Description ...............................................311
CONSULT-II Reference Value in Data Monitor Mode
.311
ECM Terminals and Reference Value ................... 312
On Board Diagnosis Logic .................................... 312
Overall Function Check ......................................... 312
Wiring Diagram ..................................................... 315
Diagnostic Procedure ............................................ 316
Main 12 Causes of Overheating ........................... 323
Component Inspection .......................................... 324
DTC P1706 PNP SWITCH ....................................... 325
Component Description ........................................ 325
CONSULT-II Reference Value in Data Monitor Mode
. 325
ECM Terminals and Reference Value ................... 325
On Board Diagnosis Logic .................................... 325
DTC Confirmation Procedure ................................ 325
Overall Function Check ......................................... 326
Wiring Diagram ..................................................... 327
Diagnostic Procedure ............................................ 328

EC-5
C
D
E
F
G
H
I
J
K
L
M
ECA DTC P1805 BRAKE SWITCH ................................ 329
Description ........................................................... 329
CONSULT-II Reference Value in Data Monitor Mode
. 329
ECM Terminals and Reference Value .................. 329
On Board Diagnosis Logic ................................... 329
DTC Confirmation Procedure ............................... 329
Wiring Diagram .................................................... 330
Diagnostic Procedure ........................................... 331
Component Inspection ......................................... 332
IGNITION SIGNAL .................................................. 334
Component Description ........................................ 334
ECM Terminals and Reference Value .................. 334
Wiring Diagram .................................................... 335
Diagnostic Procedure ........................................... 337
Component Inspection ......................................... 341
Removal and Installation ...................................... 342
INJECTOR CIRCUIT ............................................... 343
Component Description ........................................ 343
CONSULT-II Reference Value in Data Monitor Mode
. 343
ECM Terminals and Reference Value .................. 343
Wiring Diagram .................................................... 344
Diagnostic Procedure ........................................... 345
Component Inspection ......................................... 347
Removal and Installation ...................................... 347
START SIGNAL ...................................................... 348
CONSULT-II Reference Value in Data Monitor Mode
. 348
ECM Terminals and Reference Value .................. 348
Wiring Diagram .................................................... 349
Diagnostic Procedure ........................................... 350
FUEL PUMP CIRCUIT ............................................ 352
Description ........................................................... 352
CONSULT-II Reference Value in Data Monitor Mode
. 352
ECM Terminals and Reference Value .................. 352
Wiring Diagram .................................................... 354
Diagnostic Procedure ........................................... 355
Component Inspection ......................................... 357
Removal and Installation ...................................... 358
REFRIGERANT PRESSURE SENSOR ................. 359
Component Description ........................................ 359
ECM Terminals and Reference Value .................. 359
Wiring Diagram .................................................... 360
Diagnostic Procedure ........................................... 361
Removal and Installation ...................................... 362
ELECTRICAL LOAD SIGNAL ................................ 363
CONSULT-II Reference Value in Data Monitor Mode
. 363
ECM Terminals and Reference Value .................. 363
Wiring Diagram .................................................... 364
Diagnostic Procedure ........................................... 366
DATA LINK CONNECTOR ..................................... 371
Wiring Diagram .................................................... 371
EVAPORATIVE EMISSION SYSTEM ..................... 372
Description ........................................................... 372
Component Inspection ......................................... 374POSITIVE CRANKCASE VENTILATION ...............375
Description ............................................................375
Component Inspection ..........................................375
SERVICE DATA AND SPECIFICATIONS (SDS) ....377
Fuel Pressure .......................................................377
Idle Speed and Ignition Timing .............................377
Calculated Load Value ..........................................377
Mass Air Flow Sensor ...........................................377
Intake Air Temperature Sensor .............................377
Engine Coolant Temperature Sensor ...................377
Heated Oxygen Sensor 1 Heater .........................377
Heated Oxygen sensor 2 Heater ..........................377
Crankshaft Position Sensor (POS) .......................377
Camshaft Position Sensor (PHASE) ....................377
Throttle Control Motor ...........................................378
Injector ..................................................................378
Fuel Pump ............................................................378
QR (WITHOUT EURO-OBD)
INDEX FOR DTC .....................................................379
Alphabetical Index ................................................379
DTC No. Index ......................................................380
PRECAUTIONS ......................................................381
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ...............................................................381
On Board Diagnostic (OBD) System of Engine and
A/T ........................................................................381
Precaution ............................................................381
Wiring Diagrams and Trouble Diagnosis ..............384
PREPARATION .......................................................385
Special Service Tools ...........................................385
Commercial Service Tools ....................................385
ENGINE CONTROL SYSTEM ................................387
System Diagram ...................................................387
Vacuum Hose Drawing .........................................388
System Chart ........................................................389
Multiport Fuel Injection (MFI) System ...................389
Electronic Ignition (EI) System .............................392
Air Conditioning Cut Control .................................392
Fuel Cut Control (at No Load and High Engine
Speed) ..................................................................393
CAN communication .............................................393
BASIC SERVICE PROCEDURE .............................395
Idle Speed and Ignition Timing Check ..................395
Throttle Valve Closed Position Learning ...............396
Accelerator Pedal Released Position Learning ....396
Idle Air Volume Learning ......................................396
Fuel Pressure Check ............................................399
ON BOARD DIAGNOSTIC (OBD) SYSTEM ..........401
Introduction ...........................................................401
Two Trip Detection Logic ......................................401
Emission-related Diagnostic Information ..............401
NATS (Nissan Anti-theft System) .........................403
Malfunction Indicator (MI) .....................................404
TROUBLE DIAGNOSIS ..........................................407
Trouble Diagnosis Introduction .............................407

EC-6
DTC Inspection Priority Chart ...............................410
Fail-safe Chart ......................................................411
Basic Inspection ...................................................412
Symptom Matrix Chart ..........................................417
Engine Control Component Parts Location ..........421
Circuit Diagram .....................................................425
ECM Harness Connector Terminal Layout ...........427
ECM Terminals and Reference Value ...................427
CONSULT-II Function ...........................................434
CONSULT-II Reference Value in Data Monitor .....443
Major Sensor Reference Graph in Data Monitor
Mode .....................................................................446
TROUBLE DIAGNOSIS - SPECIFICATION VALUE. 449
Description ............................................................449
Testing Condition ..................................................449
Inspection Procedure ............................................449
Diagnostic Procedure ...........................................450
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT .......................................................................453
Description ............................................................453
Diagnostic Procedure ...........................................453
POWER SUPPLY CIRCUIT FOR ECM ...................454
Wiring Diagram .....................................................454
ECM Terminals and Reference Value ...................455
Diagnostic Procedure ...........................................455
Component Inspection ..........................................459
DTC U1000 CAN COMMUNICATION LINE ............460
Description ............................................................460
On Board Diagnosis Logic ....................................460
DTC Confirmation Procedure ...............................460
Wiring Diagram .....................................................461
Diagnostic Procedure ...........................................462
DTC P0102, P0103 MAF SENSOR .........................463
Component Description ........................................463
CONSULT-II Reference Value in Data Monitor Mode
.463
ECM Terminals and Reference Value ...................463
On Board Diagnosis Logic ....................................464
DTC Confirmation Procedure ...............................464
Wiring Diagram .....................................................466
Diagnostic Procedure ...........................................467
Component Inspection ..........................................469
Removal and Installation ......................................469
DTC P0117, P0118 ECT SENSOR ..........................470
Component Description ........................................470
On Board Diagnosis Logic ....................................470
DTC Confirmation Procedure ...............................471
Wiring Diagram .....................................................472
Diagnostic Procedure ...........................................473
Component Inspection ..........................................474
Removal and Installation ......................................474
DTC P0120 TP SENSOR ........................................475
Component Description ........................................475
CONSULT-II Reference Value in Data Monitor Mode
.475
ECM Terminals and Reference Value ...................475
On Board Diagnosis Logic ....................................476
DTC Confirmation Procedure ...............................476Wiring Diagram ..................................................... 479
Diagnostic Procedure ............................................ 480
Component Inspection .......................................... 482
Remove and Installation ....................................... 483
DTC P0121 APP SENSOR ...................................... 484
Component Description ........................................ 484
CONSULT-II Reference Value in Data Monitor Mode
. 484
ECM Terminals and Reference Value ................... 484
On Board Diagnosis Logic .................................... 485
DTC Confirmation Procedure ................................ 485
Wiring Diagram ..................................................... 486
Diagnostic Procedure ............................................ 487
Component Inspection .......................................... 489
Remove and Installation ....................................... 489
DTC P0134 HO2S1 ................................................. 490
Component Description ........................................ 490
CONSULT-II Reference Value in Data Monitor Mode
. 490
ECM Terminals and Reference Value ................... 490
On Board Diagnosis Logic .................................... 491
Overall Function Check ......................................... 491
Wiring Diagram ..................................................... 492
Diagnostic Procedure ............................................ 493
Component Inspection .......................................... 494
Removal and Installation ....................................... 495
DTC P0327, P0328 KS ............................................ 496
Component Description ........................................ 496
ECM Terminals and Reference Value ................... 496
On Board Diagnosis Logic .................................... 496
DTC Confirmation Procedure ................................ 496
Wiring Diagram ..................................................... 498
Diagnostic Procedure ............................................ 499
Component Inspection .......................................... 500
Removal and Installation ....................................... 500
DTC P0335 CKP SENSOR (POS) .......................... 501
Component Description ........................................ 501
CONSULT-II Reference Value in Data Monitor Mode
. 501
ECM Terminals and Reference Value ................... 501
On Board Diagnosis Logic .................................... 502
DTC Confirmation Procedure ................................ 502
Wiring Diagram ..................................................... 503
Diagnostic Procedure ............................................ 504
Component Inspection .......................................... 505
Removal and Installation ....................................... 506
DTC P0340 CMP SENSOR (PHASE) ..................... 507
Component Description ........................................ 507
ECM Terminals and Reference Value ................... 507
On Board Diagnosis Logic .................................... 507
DTC Confirmation Procedure ................................ 508
Wiring Diagram ..................................................... 509
Diagnostic Procedure ............................................ 510
Component Inspection .......................................... 512
Removal and Installation ....................................... 512
DTC P0500 VSS ...................................................... 513
Component Description ........................................ 513
ECM Terminals and Reference Value ................... 513

EC-7
C
D
E
F
G
H
I
J
K
L
M
ECA On Board Diagnosis Logic ................................... 513
DTC Confirmation Procedure ............................... 513
Overall Function Check ........................................ 514
Wiring Diagram .................................................... 515
Diagnostic Procedure ........................................... 517
DTC P0550 PSP SENSOR ..................................... 518
Component Description ........................................ 518
CONSULT-II Reference Value in Data Monitor Mode
. 518
ECM Terminals and Reference Value .................. 518
On Board Diagnosis Logic ................................... 518
DTC Confirmation Procedure ............................... 518
Wiring Diagram .................................................... 520
Diagnostic Procedure ........................................... 521
Component Inspection ......................................... 522
DTC P0605 ECM .................................................... 523
Component Description ........................................ 523
On Board Diagnosis Logic ................................... 523
DTC Confirmation Procedure ............................... 523
Diagnostic Procedure ........................................... 525
DTC P0650 MI ........................................................ 526
Component Description ........................................ 526
On Board Diagnosis Logic ................................... 526
DTC Confirmation Procedure ............................... 526
Overall Function Check ........................................ 526
Wiring Diagram .................................................... 527
Diagnostic Procedure ........................................... 528
DTC P1065 ECM POWER SUPPLY ....................... 530
Component Description ........................................ 530
On Board Diagnosis Logic ................................... 530
DTC Confirmation Procedure ............................... 530
Wiring Diagram .................................................... 531
Diagnostic Procedure ........................................... 532
DTC P1121 ELECTRIC THROTTLE CONTROL
ACTUATOR ............................................................ 534
Description ........................................................... 534
On Board Diagnosis Logic ................................... 534
DTC Confirmation Procedure ............................... 534
Diagnostic Procedure ........................................... 535
DTC P1122 ELECTRIC THROTTLE CONTROL
FUNCTION .............................................................. 536
Description ........................................................... 536
ECM Terminals and Reference Value .................. 536
On Board Diagnosis Logic ................................... 536
DTC Confirmation Procedure ............................... 537
Wiring Diagram .................................................... 538
Diagnostic Procedure ........................................... 539
Component Inspection ......................................... 540
DTC P1123 THROTTLE CONTROL MOTOR RELAY. 542
Component Description ........................................ 542
CONSULT-II Reference Value in Data Monitor Mode
. 542
ECM Terminals and Reference Value .................. 542
On Board Diagnosis Logic ................................... 542
DTC Confirmation Procedure ............................... 542
Wiring Diagram .................................................... 544
Diagnostic Procedure ........................................... 545
Component Inspection ......................................... 546DTC P1212 ESP/TCS/ABS COMMUNICATION
LINE ........................................................................547
Description ............................................................547
On Board Diagnosis Logic ....................................547
DTC Confirmation Procedure ...............................547
Diagnostic Procedure ...........................................547
DTC P1217 ENGINE OVER TEMPERATURE ........548
System Description ...............................................548
CONSULT-II Reference Value in Data Monitor Mode
.548
ECM Terminals and Reference Value ...................549
On Board Diagnosis Logic ....................................549
Overall Function Check ........................................549
Wiring Diagram .....................................................552
Diagnostic Procedure ...........................................553
Main 12 Causes of Overheating ...........................560
Component Inspection ..........................................561
DTC P1805 BRAKE SWITCH .................................562
Description ............................................................562
CONSULT-II Reference Value in Data Monitor Mode
.562
ECM Terminals and Reference Value ...................562
On Board Diagnosis Logic ....................................562
DTC Confirmation Procedure ...............................562
Wiring Diagram .....................................................564
Diagnostic Procedure ...........................................565
Component Inspection ..........................................566
HO2S1 HEATER .....................................................568
Description ............................................................568
CONSULT-II Reference Value in Data Monitor Mode
.568
ECM Terminals and Reference Value ...................568
Wiring Diagram .....................................................569
Diagnostic Procedure ...........................................570
Component Inspection ..........................................572
Removal and Installation ......................................572
HO2S2 HEATER .....................................................573
Description ............................................................573
CONSULT-II Reference Value in Data Monitor Mode
.573
ECM Terminals and Reference Value ...................573
Wiring Diagram .....................................................574
Diagnostic Procedure ...........................................575
Component Inspection ..........................................576
Removal and Installation ......................................576
IAT SENSOR ...........................................................577
Component Description ........................................577
Wiring Diagram .....................................................578
Diagnostic Procedure ...........................................579
Component Inspection ..........................................580
Removal and Installation ......................................580
HO2S1 .....................................................................581
Component Description ........................................581
CONSULT-II Reference Value in Data Monitor Mode
.581
ECM Terminals and Reference Value ...................581
Wiring Diagram .....................................................582
Diagnostic Procedure ...........................................583

EC-12
[QR (WITH EURO-OBD)]
INDEX FOR DTC
[QR (WITH EURO-OBD)]INDEX FOR DTCPFP:00024
Alphabetical IndexEBS00B0G
Check if the vehicle is a model with Euro-OBD (E-OBD) system or not by the "Type approval number" on the
identification plate. Refer toGI-45, "
IDENTIFICATION PLATE".
NOTE:
If DTC U1000 is displayed with other DTC, first perform the trouble diagnosis for DTC U1000. Refer to
EC-114
.
Items
(CONSULT-II screen terms)DTC*1
Reference page
CONSULT-II
GST*2ECM*3
APP SEN/CIRCUIT P0121 0121EC-154
A/T 1ST GR FNCTN P0731 0731AT-151
A/T 2ND GR FNCTN P0732 0732AT-158
A/T 3RD GR FNCTN P0733 0733AT-165
A/T 4TH GR FNCTN P0734 0734AT-172
ATF TEMP SEN/CIRC P0710 0710AT-136
BRAKE SW/CIRCUIT P1805 1805EC-329
CAN COMM CIRCUIT*7 U1000 1000*6EC-114
CKP SEN/CIRCUIT P0335 0335EC-217
CMP SEN/CIRCUIT P0340 0340EC-223
CYL 1 MISFIRE P0301 0301EC-206
CYL 2 MISFIRE P0302 0302EC-206
CYL 3 MISFIRE P0303 0303EC-206
CYL 4 MISFIRE P0304 0304EC-206
ECM P0605 0605EC-249
ECM BACK UP/CIRC P1065 1065EC-256
ECT SEN/CIRCUIT*5 P0117 0117EC-141
ECT SEN/CIRCUIT*5 P0118 0118EC-141
ENG OVER TEMP P1217 1217EC-311
ENGINE SPEED SIG P0725 0725AT-147
E T C A C T R P 11 2 1 11 2 1EC-271
ETC FUNCTION/CIRC P1122 1122EC-273
ETC MOT RLY/CIRC P1123 1123EC-279
FUEL SYS-LEAN-B1 P0171 0171EC-194
FUEL SYS-RICH-B1 P0172 0172EC-200
HO2S1 (B1) P0132 0132EC-160
HO2S1 (B1) P0133 0133EC-166
HO2S1 (B1) P0134 0134EC-174
HO2S1 (B1) P1143 1143EC-284
HO2S1 (B1) P1144 1144EC-290
HO2S1 HTR (B1) P0031 0031EC-120
HO2S1 HTR (B1) P0032 0032EC-120
HO2S2 (B1) P0138 0138EC-181
HO2S2 (B1) P0139 0139EC-187
HO2S2 (B1) P1146 1146EC-296
HO2S2 (B1) P1147 1147EC-303