2003 NISSAN TEANA Shock

TROUBLE DIAGNOSIS
AT-49
D
E
F
G
H
I
J
K
L
MA
B
AT

3. CHECK VEHICLE MOVE
1. Move selector lever to “P” position.
2. Turn ignition switch OFF.
3. Release parking brake.
4. Push vehicle forward or backward.
Does vehicle move when it is pushed forward or backyard?
YES >>
Mark the box AT- 1 7 6 , "In “P” Position, Vehicle Moves Forward or Backward When Pushed" on
the AT- 3 8 , "
DIAGNOSTIC WORKSHEET" .

Continue “Road Test”.
NO >> GO TO 4.
4. CHECK VEHICLE MOVE
1. Apply parking brake.
2. Start engine.
3. Move selector lever to “N” position.
4. Release parking brake.
Does vehicle move forward or backward?
YES >>
Mark the box AT- 1 7 6 , "In “N” Position, Vehicle Moves" on the AT- 3 8 , "DIAGNOSTIC WORK-
SHEET" .

Continue “Road Test”.
NO >> GO TO 5.
5. CHECK SHIFT SHOCK
1. Apply foot brake.
2. Move selector lever to “R” position.
Is there large shock when changing from
“N” to “R” position?
YES >>
Mark the box AT- 1 7 7 , "Large Shock. “N” → “R” Position" on the AT- 3 8 , "DIAGNOSTIC WORK-
SHEET" .

Continue “Road Test”.
NO >> GO TO 6.
6. CHECK VEHICLE MOVE
Release foot brake for several seconds.
Does vehicle creep backward when foot brake is released?
YES >> GO TO 7.
NO >>

Mark the box AT- 1 7 9 , "Vehicle Does Not Creep Backward in “R” Position" on the AT- 3 8 , "DIAG-
NOSTIC WORKSHEET" .

Continue “Road Test”.
7. CHECK VEHICLE MOVE
Move selector lever to “D”, “3”, “2” and “1” positions and check if vehicle creeps forward.
Does vehicle creep forward in all four positions?
YES >> Go to AT- 5 0 , "Cruise Test — Part 1" .
NO >>

Mark the box AT- 1 8 1 , "Vehicle Does Not Creep Forward in “D”, “3”, “2” or “1” Position" on the
AT- 3 8 , "
DIAGNOSTIC WORKSHEET" .

Continue “Road Test”.

TROUBLE DIAGNOSIS
AT-55
D
E
F
G
H
I
J
K
L
MA
B
AT

Symptom ChartBCS0010B
Numbers are arranged in order of inspection.
Perform inspections starting with number one and work up.
Items Symptom Condition Diagnostic item Reference page
No Lock-up
Engagement/
TCC InoperativeTorque converter
is not locked up.ON vehicle1. Accelerator pedal position sensor
EC-272
*1, EC-652*2
2. Vehicle speed sensor·A/T (Revolution
sensor) and vehicle speed sensor·MTRAT- 8 0, AT- 8 6
3. PNP switchAT- 1 6 1
4. Engine speed signalAT- 11 6
5. A/T fluid temperature sensorAT- 11 0
6. Line pressure testAT- 4 6
7. Torque converter clutch solenoid valveAT- 1 0 5
8. Control valve assemblyAT- 2 2 5
OFF vehicle 9. Torque converterAT- 2 5 5
Torque converter
clutch piston slip.ON vehicle1. A/T fluid levelAT- 1 4
2. Accelerator pedal position sensor
EC-272*1, EC-652*2
3. Line pressure testAT- 4 6
4. Torque converter clutch solenoid valveAT- 1 0 5
5. Line pressure solenoid valveAT- 1 2 6
6. Control valve assemblyAT- 2 2 5
OFF vehicle 7. Torque converterAT- 2 5 5
Lock-up point is
extremely high or
low.ON vehicle1. Accelerator pedal position sensor
EC-272
*1, EC-652*2
2. Vehicle speed sensor·A/T (Revolution
sensor) and vehicle speed sensor·MTRAT- 8 0, AT- 8 6
3. Torque converter clutch solenoid valveAT- 1 0 5
4. Control valve assemblyAT- 2 2 5
Shift ShockSharp shock in
shifting from “N”
to “D” position.ON vehicle1. Engine idle speed
EC-45
*1, EC-387*2
2. Accelerator pedal position sensor
EC-272*1, EC-652*2
3. Line pressure testAT- 4 6
4. A/T fluid temperature sensorAT- 11 0
5. Engine speed signalAT- 11 6
6. Line pressure solenoid valveAT- 1 2 6
7. Control valve assemblyAT- 2 2 5
8. N-D accumulatorAT- 2 2 5
OFF vehicle 9. Forward clutchAT- 3 0 7
Too sharp a
shock in change
from D
1 to D2 .ON vehicle1. Accelerator pedal position sensor
EC-272
*1, EC-652*2
2. Line pressure testAT- 4 6
3. Accumulator servo releaseAT- 2 2 5
4. Control valve assemblyAT- 2 2 5
5. A/T fluid temperature sensorAT- 11 0
OFF vehicle 6. Brake bandAT- 3 2 9

AT-56
TROUBLE DIAGNOSIS

Shift ShockToo sharp a
shock in change
from D
2 to D3 .ON vehicle1. Accelerator pedal position sensor
EC-272
*1, EC-652*2
2. Line pressure testAT- 4 6
3. Control valve assemblyAT-225
OFF vehicle4. High clutchAT-3015. Brake bandAT-329
Too sharp a
shock in change
from D
3 to D4 .ON vehicle1. Accelerator pedal position sensor
EC-272
*1, EC-652*2
2. Line pressure testAT- 4 6
3. Control valve assemblyAT-225
OFF vehicle4. Brake bandAT-3295. Overrun clutchAT-307
6. Forward one-way clutchAT-319
Gear change
shock felt during
deceleration by
releasing acceler-
ator pedal.ON vehicle1. Accelerator pedal position sensor
EC-272*1, EC-652*2
2. Line pressure testAT- 4 6
3. Overrun clutch solenoid valveAT-100
4. Control valve assemblyAT-225
Large shock
changing from 1
2
to 1
1 in “1” posi-
tion.ON vehicle 1. Control valve assemblyAT-225OFF vehicle 2. Low & reverse brakeAT-315
Improper Shift
TimingToo high a gear
change point from
D
1 to D2 , from
D
2 to D3 , from
D
3 to D4 .ON vehicle1. Accelerator pedal position sensor
EC-272
*1, EC-652*2
2. Vehicle speed sensor·A/T (Revolution
sensor) and vehicle speed sensor·MTRAT- 8 0, AT- 8 6
3. Shift solenoid valve AAT- 9 0
4. Shift solenoid valve BAT- 9 5
Gear change
directly from D
1
to D
3 occurs.ON vehicle1. A/T fluid levelAT- 1 4
2. Accumulator servo releaseAT-225
OFF vehicle 3. Brake bandAT-329
Too high a
change point from
D
4 to D3 , from
D
3 to D 2 , from
D
2 to D1 .ON vehicle1. Accelerator pedal position sensor
EC-272
*1, EC-652*2
2. Vehicle speed sensor·A/T (Revolution
sensor) and vehicle speed sensor·MTRAT- 8 0, AT- 8 6
Kickdown does
not operate when
depressing pedal
in D
4 within kick-
down vehicle
speed.ON vehicle1. Accelerator pedal position sensor
EC-272
*1, EC-652*2
2. Vehicle speed sensor·A/T (Revolution
sensor) and vehicle speed sensor·MTRAT- 8 0, AT- 8 6
3. Shift solenoid valve AAT- 9 0
4. Shift solenoid valve BAT- 9 5
Kickdown oper-
ates or engine
overruns when
depressing pedal
in D
4 beyond
kickdown vehicle
speed limit.ON vehicle1. Vehicle speed sensor·A/T (Revolution
sensor) and vehicle speed sensor·MTRAT- 8 0
, AT- 8 6
2. Accelerator pedal position sensor
EC-272*1, EC-652*2
3. Shift solenoid valve AAT- 9 0
4. Shift solenoid valve BAT- 9 5
Gear change
from 2
2 to 23 in
“2” position.ON vehicle1. PNP switchAT-161
2. A/T positionAT-215
Items Symptom Condition Diagnostic item Reference page

AT-60
TROUBLE DIAGNOSIS

Slips/Will Not
EngageNo creep at all.
AT- 1 7 9
, AT-181
ON vehicle1. A/T fluid levelAT- 1 42. Line pressure testAT- 4 6
3. Control valve assemblyAT-225
OFF vehicle4. Forward clutchAT-3075. Oil pumpAT-275
6. Torque converterAT-255
Almost no shock
or clutches slip-
ping in change
from D
1 to D2 .ON vehicle1. A/T fluid levelAT- 1 4
2. Accelerator pedal position sensor
EC-272*1, EC-652*2
3. Line pressure testAT- 4 6
4. Accumulator servo releaseAT-225
5. Control valve assemblyAT-225
OFF vehicle 6. Brake bandAT-329
Almost no shock
or slipping in
change from D
2
to D
3 .ON vehicle1. A/T fluid levelAT- 1 4
2. Accelerator pedal position sensor
EC-272*1, EC-652*2
3. Line pressure testAT- 4 6
4. Control valve assemblyAT-225
OFF vehicle5. High clutchAT-3016. Forward clutchAT-307
Almost no shock
or slipping in
change from D
3
to D
4 .ON vehicle1. A/T fluid levelAT- 1 4
2. Accelerator pedal position sensor
EC-272*1, EC-652*2
3. Line pressure testAT- 4 6
4. Control valve assemblyAT-225
OFF vehicle 5. Brake bandAT-329
Races extremely
fast or slips in
changing from D
4
to D
3 when
depressing pedal.ON vehicle1. A/T fluid levelAT- 1 4
2. Accelerator pedal position sensor
EC-272*1, EC-652*2
3. Line pressure testAT- 4 6
4. Line pressure solenoid valveAT-126
5. Shift solenoid valve AAT- 9 0
6. Control valve assemblyAT-225
OFF vehicle7. Brake bandAT-3298. Forward clutchAT-307
Races extremely
fast or slips in
changing from D
4
to D
2 when
depressing pedal.ON vehicle1. A/T fluid levelAT- 1 4
2. Accelerator pedal position sensor
EC-272*1, EC-652*2
3. Line pressure testAT- 4 6
4. Line pressure solenoid valveAT-126
5. Shift solenoid valve AAT- 9 0
6. Shift solenoid valve BAT- 9 5
7. Control valve assemblyAT-225
OFF vehicle8. Brake bandAT-3299. Forward clutchAT-307
Items Symptom Condition Diagnostic item Reference page

TROUBLE DIAGNOSIS FOR SYMPTOMS
AT-177
D
E
F
G
H
I
J
K
L
MA
B
AT

4. DETECT MALFUNCTIONING ITEM
1. Disassemble A/T. Refer to AT- 2 5 5 , "
Disassembly" .
2. Check the following items:
–Forward clutch assembly. Refer to AT- 3 0 7 , "Forward and Overrun Clutches" .
–Overrun clutch assembly. Refer to AT- 3 0 7 , "Forward and Overrun Clutches" .
–Reverse clutch assembly. Refer to AT- 2 9 6 , "Reverse Clutch" .
OK or NG
OK >> GO TO 5.
NG >> Repair or replace damaged parts.
5. SYMPTOM CHECK
Check again. Refer to AT- 4 8 , "
Check at Idle" .
OK or NG
OK >>INSPECTION END
NG >> GO TO 6.
6. CHECK TCM
1. Check TCM input/output signals. Refer to AT- 6 4 , "
TCM Terminals and Reference Value" .
2. If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK >>INSPECTION END
NG >> Repair or replace damaged parts.
Large Shock. “N” → “R” PositionBCS0014D
SYMPTOM:
Large shock when shifting from “N” to “R” position.
DIAGNOSTIC PROCEDURE
1. CHECK SELF-DIAGNOSTIC RESULTS (ECM)
Perform self-diagnosis. Refer to EC-82, "
SELF-DIAG RESULTS MODE" (QR engine) or EC-427, "SELF-
DIAG RESULTS MODE" (VQ engine).
Is any malfunction detected by self-diagnostic results?
YES >> Check the malfunctioning system. Refer to EC-82, "SELF-DIAG RESULTS MODE" (QR engine)
or EC-427, "
SELF-DIAG RESULTS MODE" (VQ engine).
NO >> GO TO 2.
2. CHECK SELF-DIAGNOSTIC RESULTS (TCM)
Perform self-diagnosis. Refer to AT- 6 9 , "
SELF-DIAGNOSTIC RESULT MODE" or AT- 7 6 , "Diagnostic Proce-
dure Without CONSULT-II" .
Is any malfunction detected by self-diagnostic results?
YES >> Check the malfunctioning systems. Refer to AT- 6 9 , "SELF-DIAGNOSTIC RESULT MODE" or AT-
77, "Judgement of Self-Diagnosis Code" .
NO >> GO TO 3.

POWER DOOR LOCK SYSTEM
BL-23
C
D
E
F
G
H
J
K
L
MA
B
BL


through body grounds M71 and M72.
When you meet either the above-mentioned
Power is supplied

through BCM terminal 51

to each door lock actuator terminal 2
Ground is supplied

to each door lock actuator terminal 3

through BCM terminal 50.
Each door lock actuator unlocks the door lock
When the front door switch (driver side) is ON (door is OPEN), ground is supplied

to BCM terminal 62

through front door switch (driver side) terminal 2

through front door switch (driver side) case ground.
When the front door switch (passenger side) is ON (door is OPEN), ground is supplied

to BCM terminal 12

through front door switch (passenger side) terminal 2

through front door switch (passenger side) case ground.
When the rear door switch LH is ON (door is OPEN), ground is supplied

to BCM terminal 63

through rear door switch LH terminal 2

through rear door switch LH case ground.
When the rear door switch RH is ON (door is OPEN), ground is supplied

to BCM terminal 13

through rear door switch RH terminal 2

through rear door switch RH case ground.
KEY REMINDER DOOR SYSTEM
When door lock and unlock switch is operated to lock doors with ignition key put in key cylinder and or door
open, all door lock actuators are locked and then unlocked.
VEHICLE SPEED SENSING AUTO DOOR LOCK FUNCTION

When the vehicle speed exceeds more than 26 km/h (16MPH), all doors are automatically locked.

After auto door is locked, and once again the door lock is released, this function does not operate.

This function returns to the normal operation when either opening doors or turning key switch OFF.

After operating shock sensing auto door unlock function, this function does not operate until key is
released. (For vehicle with intelligent key, until key switch is turned to OFF.)
OVERRIDE MECHANISM
When an inside handle is pulled while driver side door lock knob is being locked, door is unlocked and opens.
And, all doors are unlocked.
CAN Communication System DescriptionBIS000VX
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitBIS000VY
Refer to LAN-49, "CAN System Specification Chart" .

BL-30
POWER DOOR LOCK SYSTEM

CONSULT-II Function (BCM)BIS000W3
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II START PROCEDURE
Refer to GI-34, "CONSULT-II Start Procedure" .
CONSULT-II APPLICATION ITEMS
Data Monitor
*: With Intelligent Key system
Active Test
BCM diagnosis
partInspection item, Self-diagnosis
modeContent
Door lockDATA MONITOR Displays BCM input data on real-time basis.
ACTIVE TEST Sends drive signals to door lock actuator to perform operation check.
Monitor item Content
IGN ON SW Indicates [ON/OFF] condition of ignition switch in ON position.
KEY ON SW Indicates [ON/OFF] condition of key switch.
CDL LOCK SW Indicates [ON/OFF] condition of lock signal from door lock and unlock switch.
CDL UNLOCK SW Indicates [ON/OFF] condition of unlock signal from door lock and unlock switch.
DOOR SW-DR Indicates [ON/OFF] condition of front door switch driver side.
DOOR SW-AS Indicates [ON/OFF] condition of front door switch passenger side.
DOOR SW-RR Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL Indicates [ON/OFF] condition of rear door switch LH.
BACK DOOR SW This is displayed even when it is not equipped.
LOCK STATUS Indicates [ON/OFF] condition of driver side door lock knob
SHOCK SENSOR Indicates [ON/OFF] condition of shock sensor
VEHICLE SPEED Indicates [km/h] condition of vehicle speed
KEYLESS LOCK Indicates [ON/OFF] condition of lock signal from keyfob.
KEYLESS UNLOCK Indicates [ON/OFF] condition of unlock signal from keyfob.
I-KEY LOCK* Indicates [ON/OFF] condition of lock signal from door request switch.
I-KEY UNLOCK* Indicates [ON/OFF] condition of unlock signal from door request switch.
Test item Content
DOOR LOCKThis test is able to check all door lock actuators lock or unlock operation.
These actuators lock or unlock when “LOCK” or “UNLOCK” on CONSULT-II screen is touched.

PRECAUTIONS
BRC-37
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC

[VDC/TCS/ABS]PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
BFS000G3
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Brake SystemBFS000DL

Recommended fluid is brake fluid “DOT 3” or “DOT 4”. Refer to MA-14, "RECOMMENDED FLUIDS AND
LUBRICANTS" .

Never reuse drained brake fluid.

Be careful not to splash brake fluid on painted areas.

To clean or wash all parts of master cylinder and disc brake caliper, use clean brake fluid.

Never use mineral oils such as gasoline or kerosene. They will
ruin rubber parts of the hydraulic system.

Using a flare nut wrench when removing flare nuts, and use a
flare nut torque wrench when tighten brake tube flare nuts.

When installing brake tubes, be sure to check torque.

Before working, turn ignition switch OFF and disconnect electri-
cal connector of ABS actuator and electric unit (control unit) or
battery negative terminal.
WARNING:
Clean brake pads and shoes with a waste cloth, then wipe with
a dust collector.
Precautions for Brake ControlBFS000DM

During ABS operation, brake pedal lightly vibrates and a mechanical noise may be heard. This is normal.

Just after starting vehicle after ignition switch ON, brake pedal may vibrate or motor operating noise may
be heard from engine room. This is a normal status of operation check.

Stopping distance may be longer than that of vehicles without ABS when vehicle drives on rough, gravel,
or snow-covered (fresh, deep snow) roads.

When an error is indicated by ABS or another warning lamp, collect all necessary information from cus-
tomer (what symptoms are present under what conditions) and check for simple causes before starting
diagnostic servicing. Besides electrical system inspection, check brake booster operation, brake fluid
level, and fluid leaks.

If tire size and type are used in an improper combination, or brake pads are not Genuine NISSAN parts,
stopping distance or steering stability may deteriorate.

If there is a radio, antenna, or antenna lead-in wire (including wiring) near control module, ABS function
may have a malfunction or error.

If aftermarket parts (car stereo, CD player, etc.) have been installed, check for incidents such as harness
pinches, open circuits, and improper wiring.

If the following components are replaced with non-genuine components or converted, the VDC OFF indi-
cator lamp and SLIP indicator lamp may turn on or the VDC system may not operate properly. Compo-
nents related to suspension (Shock Absorber, Strut, Spring, Bush, etc.), Tires, wheels (exclude specified
SBR820BA