2003 MITSUBISHI SHOGUN inflation pressure

Exterior
EB21DOIb
B21D219T
1- Engine compartment→P.10-15
Bonnet→P.2-9
2- Windscreen wiper and washer→P.4-17
3- Sunroof*→P.2-15
4- Outside rear-view mirrors→P.5-50
5- Electric window control→P.2-12
6- Locking and unlocking→P.2-4
Keyless entry system*→P.2-5
7- Antenna→P.6-35
8- Headlamps→P.4-14, 8-34, 8-35
9- Front fog lamps*→P.4-22, 8-34, 8-38
10- Turn-signal lamps
→P.4-15, 8-34, 8-37, 8-41
11- Position lamps→P.4-14, 8-34, 8-36
12- Side step lamps*→P.2-7, 8-34, 8-39
13- High-mounted stop lamp→P.8-35, 8-42
14- Backdoor→P.2-10
15- Rear window wiper and washer
→P.4-19
16- Rear fog lamp (LHD only)
→P.4-22, 8-35, 8-41
17- Number plate lamps→P.8-35, 8-42
18- Spare wheel→P.8-11
19- Stop and tail lamps→P.8-35, 8-41
20- Rear fog lamp (RHD only)
→P.4-22, 8-35, 8-41
21- Reversing lamps→P.8-35, 8-41
22- Tyre inflation pressure→P.9-14
Changing tyres→P.8-13
Tyre rotation→P.9-15
Tyre chains→P.9-16
23- Fuel tank filler→P.5-4
Div:
Out put date:

(8) Stop driving the vehicle if you think the
performance is noticeably low, or that
there is unnecessary engine rotation, or
any other engine trouble, such as with
the ignition, etc.
If it is impractical to stop driving imme-
diately, reduce the speed and drive for
only a short time. Have an inspection
made by your nearest authorized
MITSUBISHI dealer as soon as pos-
sible.
(9) In unusual situations involving grossly
malfunctioning engine operation, a
burnt smell may indicate severe and
abnormal catalyst overheating.
If this occurs, the vehicle should be
stopped in a safe place, the engine
switched off and the vehicle allowed to
cool. Once the engine is cool, a ser-
vice, including a tune-up to manufac-
turer’s specifications, should be
obtained immediately.
Economical driving
EC19AAX
For economical driving, there are some
technical requirements that have to be met.
The prerequisite for low fuel consumption
is a properly adjusted engine. In order to
achieve longer life of the vehicle and the
most economical operation, have the
vehicle serviced by an authorized
MITSUBISHI dealer at regular intervals in
accordance with the service standards.
Fuel economy and generation of exhaust
gas and noise are highly influenced by per-
sonal driving habits as well as the particu-
lar operating conditions. The following
points should be observed in order to mini-
mize wear of brakes, tyres and engine as
well as to reduce environmental pollu-
tion.
(1)Starting
Avoid rapid acceleration and sudden
starts; such operation will result in
higher fuel consumption.
(2)Shifting
Shift only at an appropriate speed and
engine speed. Always use the high-
est gear possible.
The transfer shift lever should be set to
“2H”when driving on normal roads and
express ways to obtain best possible
fuel economy.(3)City traffic
Frequent starting and stopping
increases the average fuel consump-
tion. Use roads with smooth traffic flow
whenever possible. When driving on
congested roads, avoid use of a low
gear at high engine speeds.
(4)Idling
The vehicle consumes fuel even dur-
ing idling. Avoid extended idling when-
ever possible.
(5)Speed
The higher the vehicle speed, the more
fuel consumed. Avoid driving at full
speed. Even a slight release of the
accelerator pedal will save a signifi-
cant amount of fuel.
(6)Tyre inflation pressure
Check the tyre inflation pressures at
regular intervals. Low tyre inflation
pressure increases road resistance and
fuel consumption. In addition, low tyre
pressures adversely affect tyre wear
and driving stability.
Starting and driving
5-7
Div:
Out put date:

Cautions on handling of 4WD
vehicles
EI49A-Xa
Tyre and disc wheelsSince the driving torque can be applied to
the 4 wheels, the performance of the
vehicle when operating in 4WD is greatly
affected by the condition of the tyres.
Pay close attention to the tyres.
•Install specified tyres on all wheels. Refer
to“Tyre and wheels”on page 10-10.
•Be sure to equip the car with all four tyres
and wheels of the same size and type.
When replacement of any of the tyres or
wheels is necessary, replace all of them.
•All tyres should be rotated whenever the
wear difference between front and rear
tyres is recognizable.
Good vehicle performance cannot be
expected if there is a difference in wear
between tyres. Refer to the“Tyre rotation”
on page 9-15.
•Check the tyre inflation pressure regu-
larly.
CAUTION
Always use tyres of the same size,
same type, and same brand, which
have no wear differences.
Using the tyres of differ in size, type,
brand or a different degree of wear
will cause excessive loading, result-
ing in possible damage to the drive
system.Jacking up a 4-wheel drive vehicles
WARNING
Do not crank the engine while jack-
ing up the vehicle.
The tyre on the ground may turn and
the vehicle may roll off the jack.Operate clutch pedal slowly and
positivelyQuick or slight clutch engagement made
while the engine is running at high speed
will cause damage to the clutch and trans-
mission because the tractive force is very
great.
Operate the pedal slowly and positively.
I07A002A
1
Parking brake
EI07AAEd
To park the vehicle, first bring it to a com-
plete stop, fully engage the parking brake,
and then move the gearshift lever to 1st (on
an uphill) or Reverse (on a downhill) posi-
tion, for vehicles with a manual transmis-
sion or set the selector lever to“P”(PARK)
position on automatic transmission
vehicles.To apply1- Pull the lever up without pushing the
button at the end of the hand grip.
Starting and driving
5-42Div:
Out put date:

On a flooded road(1) Avoid flooded roads. Water could enter
the brake discs, resulting in tempo-
rarily ineffective brakes. In such cases,
lightly depress the brake pedal to see
if the brakes operate properly. If they do
not, lightly depress the pedal several
times while driving in order to dry the
brake pads.
(2) When driving in rain or on a road with
many puddles a layer of water may
form between the tyres and the road
surface.
This reduces a tyre’s frictional resis-
tance on the road, resulting in loss of
steering stability and braking capabil-
ity.
To cope with this, observe the follow-
ing items:
(a)Drive your vehicle at a slow speed.
(b)Do not drive on worn tyres. Always
maintain the specified tyre inflation
pressures.
On a snow-covered or frozen road(1) When driving on a snow-covered or fro-
zen road, it is recommended that you
use snow tyres or tyre chains.
Refer to the“Snow tyres”and“Tyre
chains”sections.
(2) Avoid high-speed operation, sudden
acceleration, abrupt brake applica-
tion and sharp cornering.
(3) Depressing the brake pedal during
travel on such a road may cause tyre
slippage and skidding. When traction
between the tyres and the road is
reduced the wheels may skid and the
vehicle cannot readily be brought to a
stop by conventional braking tech-
niques. Braking will differ, depending
upon whether you have anti-lock
brakes (ABS). If you do have ABS,
brake by pressing the brake pedal
hard, and keeping it pressed. If you do
not have ABS, pump the brake pedal
with short rapid jabs, each time fully
applying and fully releasing for great-
est effect.
(4) Allow extra distance between your
vehicle and the vehicle in front of you,
and avoid sudden braking.
Tools and jack
EN01BOI
The storage location of the tools and jack
should be remembered in case of an emer-
gency.
For emergencies
8-3
Div:
Out put date:

CAUTION
(1) Grasp the spare wheel firmly
when removing or attaching it.
(2) When removing the spare wheel,
put on gloves. Removing the
spare wheel with your hands
may cause injury to the fin-
gers.
(3) Check the air pressure of the
spare wheel frequently and
make sure it is ready for emer-
gency use at any time.
Driving with an insufficient tyre
pressure can lead to an acci-
dent. If you have no choice but
to drive with an insufficient tyre
pressure, keep your speed down
and inflate the tyre to the cor-
rect pressure as soon as pos-
sible. (Refer to“Tyre inflation
pressure”on page 9-14.)
Maintaining the spare wheel at
the highest specified air pres-
sure will ensure that it can
always be used under any con-
ditions (city/high-speed driv-
ing, varying load weight, etc.)
N03A082A
Removal of spare wheel
1. To remove the bolt cover, insert the igni-
tion key into the lock, pulling the bolt
cover with the key still in it towards you.
N03A359A
2. Then loosen the spare wheel bolts with
the wheel nut wrench.
And then remove the spare wheel.
For emergencies
8-12Div:
Out put date:

N24A119A
Type 2On the aluminium wheel type vehicle (Type
2), temporarily tighten the wheel nuts by
hand until the flanges of the wheel nuts
come into contact with the wheel.
NOTE
(1) Flange nuts (Type 2) can be tempo-
rarily used on the steel wheel, but
return to the original wheel and tyre as
soon as possible.
(2) If all four wheels on vehicles with flange
nuts (Type 2) are changed to steel
wheels, use tapered nuts (Type 1).
CAUTION
Never apply oil to either wheel bolts
or nuts, as it will cause them to over-
tighten.
N24A286A
9. Lower the vehicle slowly and then
tighten the nuts crisscross in two or
three steps until each nut has been
tightened securely.
Tightening torque:
98 to 118 Nm
(Achieved by applying a force of 370 to
430 N at the end of the wheel nut
wrench supplied with the vehicle)
CAUTION
Never use extra force by your foot to
the wheel nut wrench or by using a
pipe extension as you can over-
tighten the nut.
10. Lower and remove the jack and stow
the jack, jack handle, wheel nut wrench
and flat tyre wheel. Have the flat tyre
repaired as soon as possible.
N24A100A
11. Check tyre inflation pressure. The infla-
tion pressure specification is shown on
the label. Refer to the illustration.
For emergencies
8-16Div:
Out put date:

Maintenance
Engine oil ...................................................... 9- 2
Automatic transmission fluid ...................... 9- 4
Engine coolant ............................................. 9- 5
Battery ........................................................... 9- 6
Brake fluid .................................................... 9- 8
Power steering fluid...................................... 9- 9
Clutch fluid ................................................... 9-10
Washer fluid ................................................... 9-11
Wheel condition ............................................ 9-12
Tyre inflation pressure ................................. 9-14
Tyre rotation ................................................. 9-15
Snow tyres .................................................... 9-16
Tyre chains ................................................... 9-16
Fuel, engine coolant,
oil and exhaust gas leakage..................... 9-17
Exterior and interior lamp operation........... 9-18
Meter, gauge and indication /
warning lamp operation ............................ 9-18
Clutch pedal free play ................................. 9-18
Brake pedal free play.................................... 9-18
Parking brake lever stroke ........................... 9-19
Hinges and latches lubrication.................... 9-19
Wiper blades.................................................. 9-19
Ventilation slots ............................................ 9-21
Weatherstripping........................................... 9-21
Additional equipment
(For regions where snow is encountered). 9-21
Div:
Out put date:

Tyre inflation pressure
EM13AOIbar (kPa)
To 5 passengers To max. load At trailer towing
Front Rear Front Rear Front Rear
235/80R16 109S2.0 (200),
2.0 (200)*2.0 (200),
2.1 (210)*2.0 (200),
2.0 (200)*2.2 (220),
2.4 (240)*2.0 (200) 2.4 (240)
265/70R16 112H2.0 (200),
2.0 (200)*2.0 (200),
2.0 (200)*2.0 (200),
2.0 (200)*2.0 (200),
2.3 (230)*2.0 (200) 2.4 (240)
265/70R16 112S2.0 (200),
2.0 (200)*2.0 (200),
2.0 (200)*2.0 (200),
2.0 (200)*2.0 (200),
2.2 (220)*2.0 (200) 2.4 (240)
*: Above 160 km/h
Check the tyre inflation pressure of all the tyres while they are cold; if insufficient or excessive, adjust to the specified value.
After the tyre inflation pressure has been adjusted, check the tyres for damage and air leaks. Be sure to put rubber caps on the valves.
Maintenance
9-14Div:
Out put date: