2003 MITSUBISHI SHOGUN heating

CAUTION
(1) Use a foot to operate the pedal
(2).
(2) The reclining mechanism of the
seatback is spring loaded, caus-
ing it to return to the vertical
position when the lock lever is
operated. When using the lever,
sit close to the seatback or hold
it with your hand.
WARNING
The front seatbacks also serve the
purpose of protecting passengers in
the rear seat from being thrown for-
wards in case of an accident. Thus,
in order to prevent serious injury, the
vehicle should not be driven with a
seatback tilted forward.
G16A030A
Heated seats*
EG16A-J
The heated seats can be operated with the
ignition switch in the“ON”position.
1- Heater high (for quick heating).
2- Heater off.
3- Heater low (to keep the seat warm).
The indication lamp (A) will illuminate while
the heater is on.
CAUTION
(1) Switch off seat heaters when not
in use.
(2) Operate in the high position for
quick heating. Once the seat is
warm, set the heater to low to
keep it warm. Slight variations in
seat temperature may be felt
while using the heated seats.
This is caused by the opera-
tion of the heater’s internal ther-
mostat and does not indicate a
malfunction.
(3) If the following types of per-
sons use the heated seats, they
might become too hot or receive
minor burns (red skin, heat blis-
ters, etc.):
·Children, elderly or ill people
·People with sensitive skin
·Excessively tired people
·People under the influence of
alcohol or sleep inducing medi-
cation (cold medicine, etc.)
(4) Do not use a blanket, cushion, or
other material with high heat
insulation properties on the seat
while using the heater; this
might cause the heater ele-
ment to overheat.
Seat and seat belts
3-10Div:
Out put date:

D06A047A
Water temperature gauge
ED06A-Nb
The water temperature gauge indicates the
engine coolant temperature when the igni-
tion switch is“ON”.
CAUTION
If the indication needle enters the
zone “A” while the engine is run-
ning, it indicates that the engine is
possibly overheating. Immediately
park your vehicle in a safe place and
make the necessary corrections.
(Refer to “Engine overheating” on
page 8-21.)
While driving, care should always be
taken to maintain the normal operat-
ing temperature.
Instruments and controls
4-5
Div:
Out put date:

(8) Stop driving the vehicle if you think the
performance is noticeably low, or that
there is unnecessary engine rotation, or
any other engine trouble, such as with
the ignition, etc.
If it is impractical to stop driving imme-
diately, reduce the speed and drive for
only a short time. Have an inspection
made by your nearest authorized
MITSUBISHI dealer as soon as pos-
sible.
(9) In unusual situations involving grossly
malfunctioning engine operation, a
burnt smell may indicate severe and
abnormal catalyst overheating.
If this occurs, the vehicle should be
stopped in a safe place, the engine
switched off and the vehicle allowed to
cool. Once the engine is cool, a ser-
vice, including a tune-up to manufac-
turer’s specifications, should be
obtained immediately.
Economical driving
EC19AAX
For economical driving, there are some
technical requirements that have to be met.
The prerequisite for low fuel consumption
is a properly adjusted engine. In order to
achieve longer life of the vehicle and the
most economical operation, have the
vehicle serviced by an authorized
MITSUBISHI dealer at regular intervals in
accordance with the service standards.
Fuel economy and generation of exhaust
gas and noise are highly influenced by per-
sonal driving habits as well as the particu-
lar operating conditions. The following
points should be observed in order to mini-
mize wear of brakes, tyres and engine as
well as to reduce environmental pollu-
tion.
(1)Starting
Avoid rapid acceleration and sudden
starts; such operation will result in
higher fuel consumption.
(2)Shifting
Shift only at an appropriate speed and
engine speed. Always use the high-
est gear possible.
The transfer shift lever should be set to
“2H”when driving on normal roads and
express ways to obtain best possible
fuel economy.(3)City traffic
Frequent starting and stopping
increases the average fuel consump-
tion. Use roads with smooth traffic flow
whenever possible. When driving on
congested roads, avoid use of a low
gear at high engine speeds.
(4)Idling
The vehicle consumes fuel even dur-
ing idling. Avoid extended idling when-
ever possible.
(5)Speed
The higher the vehicle speed, the more
fuel consumed. Avoid driving at full
speed. Even a slight release of the
accelerator pedal will save a signifi-
cant amount of fuel.
(6)Tyre inflation pressure
Check the tyre inflation pressures at
regular intervals. Low tyre inflation
pressure increases road resistance and
fuel consumption. In addition, low tyre
pressures adversely affect tyre wear
and driving stability.
Starting and driving
5-7
Div:
Out put date:

Normal conditions
The starting procedure is as follows:
1. Insert the ignition key and fasten the
seat belt.
2. Apply the parking brake.
3. Depress and hold the brake pedal.
4. Place the gearshift lever (manual
transmission) in the“N”(Neutral) or the
selector lever (automatic transmission)
in the“P”(PARK) position.
5. Fully depress the clutch pedal (manual
transmission).
6. After turning the ignition key to the“ON”
position, make certain that all warning
lamps are functioning properly before
starting the engine.
7. Turn the ignition key to the“START”
position without depressing the accel-
erator pedal, and release it when the
engine starts.NOTE
A ticking noise may be heard after start-
ing the engine. This is not an abnormal
condition. The noise will disappear after a
short time of engine running.
If the ticking noise continues after the
engine is warmed up, have your vehicle
checked at an authorized MITSUBISHI
dealer.
Flooded engine
If the engine was flooded during starting,
first operate the starter for 5 to 6 seconds
while fully depressing the accelerator pedal,
then start the engine without depressing the
accelerator pedal.
At extreme cold ambient temperature
If the engine won’t start, depress the accel-
erator pedal about halfway while crank-
ing the engine. Once the engine starts,
release the accelerator pedal.
CAUTION
When starting the engine, make sure
that you press on the brake pedal. At
extreme cold ambient temperature
move your foot to the brake pedal
immediately after the engine has
started.
I27A072A
M/T A/TStarting the engine (diesel-powered
vehicles)
EI02BAI
1. Insert the ignition key and fasten the
seat belt.
2. Apply the parking brake.
3. Depress and hold the brake pedal.
4. On vehicles with a manual transmis-
sion, place the gearshift lever in the“N”
(Neutral) position and depress the clutch
pedal all the way.
On vehicles with an automatic trans-
mission, place the selector lever in the
“P”(PARK) position.
5. Turn the ignition key to the“ON”posi-
tion.
The diesel preheat warning lamp will first
illuminate, and then after a short time go
out, indicating that preheating is com-
pleted.
Starting and driving
5-14Div:
Out put date:

CAUTION
(1) Do not force the vehicle or drive
recklessly on sandy surfaces. In
comparison with normal road
surfaces, the engine and other
drive-system components are
put under excessive strain when
driving on such a surface, and
this could lead to accidents.
(2) If any of following conditions
occur while the vehicle is being
driven, immediately park your
vehicle in a safe place and fol-
low these procedures:
•The needle in the tempera-
ture gauge approaches the
overheating zone.
Refer to the“Engine
overheating”on page 8-21.
•A/T fluid temperature warning
lamp illuminates.
Refer to the“A/T fluid tempera-
ture warning lamp”on page
4-11.
WARNING
When attempting to rock your vehicle
out of a stuck position, be sure that
the area around the vehicle is clear of
people and physical objects. The
rocking motion may cause the
vehicle to suddenly launch forward
or backward, causing injury or dam-
age to nearby people or objects.
NOTE
(1) Avoid sudden braking, acceleration, and
turning; such operations could result in
the vehicle becoming stuck.
(2) If the vehicle becomes stuck in sandy
or muddy roads, it can often be moved
a rocking motion. Move the selector
lever rhythmically between the“D”
(DRIVE) and“R”(REVERSE) posi-
tion (with manual transmission,
between 1st and Reverse), while apply-
ing slight pressure to the accelerator
pedal.
(3) It is recommended to start the vehicle
with parking brake partially, but not
completely, applied by slightly pulling
the parking brake lever.
After the vehicle has become free, do
not forget to release the parking brake.NOTE
(4) If it is necessary to drive in extremely
muddy conditions, the use of tyre
chains is recommended. Because the
extent of muddy conditions is difficult to
judge and the vehicle could become
bogged down very deeply, operation
should be at a low speed. If possible,
get out of the vehicle and check the
conditions ahead before proceeding.
(5) Driving over roads in coastal areas or
roads on which anti-skid preparations
have been spread can cause rust on
the vehicle; wash the vehicle thor-
oughly as soon as possible after such
use.
Climbing sharp gradesSet the transfer shift lever to“4L”(part time
4WD) or“4LLc”(super select 4WD II) to
maximize the engine torque.
WARNING
(1) Go straight up. Do not try to
traverse across a steep slope.
(2) If you begin to lose traction, ease
off the accelerator pedal and
gently turn the steering wheel
alternatively left and right to
regain adequate traction again.
Starting and driving
5-39
Div:
Out put date:

Brake pads(1) With new brake pads, avoid where pos-
sible sudden full application of the
brakes for the first 200 km (125 miles)
of driving.
(2) The disc brakes are provided with a
warning device which emits a shriek-
ing metallic sound while braking if the
brake pads have reached their limit.
If you hear this sound, have the brake
pads replaced by your MITSUBISHI
dealer.
CAUTION
(1) Do not leave any objects or place
a thick floor mat around the
brake pedal; doing so could pre-
vent the full pedal stroke that
would be necessary in an emer-
gency. Make sure that the pedal
can be operated freely at all
times.
(2) Avoid driving habits that cause
heavy braking and never“ride”
the brakes by resting your foot
on the brake pedal while driv-
ing.
It causes brake overheating and
fade.
Anti - lock brake system (ABS)*
EI24ABCb
Environmental conditions can have an
effect on braking. During sudden braking
when there is snow, ice, oil, water etc. on
the road surface, a skid may occur. In this
situation, steering control and braking effec-
tiveness are reduced and the stopping dis-
tance is increased. The vehicle may also
go into an uncontrolled spin.
The ABS helps prevent the wheels from
locking during braking, thus maintaining
directional stability, ensuring controlabil-
ity and providing optimum braking force.Driving hints(1) With ABS fitted, steering during sud-
den braking (when the ABS functions)
differs slightly from when the brakes
are not being applied.
Steer the vehicle carefully in these con-
ditions.(2) Always maintain the same distance
from the vehicle in front of you as you
would for a vehicle not equipped with
ABS.
Compared with vehicles not fitted with
ABS, your vehicle may require a longer
stopping distance in the following
cases:
•Driving on gravel or snow-covered
roads.
•Driving with tyre chains installed.
•Driving on roads where the road sur-
face is pitted or has other differ-
ences in surface height.
•Driving on bumpy roads or other poor
driving surfaces.
(3) In order to ensure that the anti-lock
brake system (ABS) will operate cor-
rectly in situations where tyre chains
have been fitted, drive in“4H”or“4L”
for part time 4WD, or in“4H”,“4HLc”,
or“4LLc”for super select 4WD II.
(4) Operation of ABS is not restricted to
situations where brakes are applied
suddenly. This system may also oper-
ate to prevent wheel lock when you are
driving over manholes, steel road-work
plates, or the vehicle is driven over
steps or level differences in the road,
road markings, or other surfaces which
are difficult for the wheels to grip.
Starting and driving
5-45
Div:
Out put date:

4- Mode selection dial
Main flow directions:
(Face position)
Air flows to the upper part of the
passenger compartment.(Foot/face position)
Air flows to the upper part of the
passenger compartment, and the leg
area.(Foot position)
Air flows to the leg areas.(Foot/ demister position)
Air flows to the leg areas, wind-
screen and door windows.(Demister position)
Air flows to the windscreen and the
door windows.
NOTE
Air always flows out from the side ventila-
tors regardless of the mode selection dial
position.5- Air selection switch
Every time the switch is pressed, alter-
ation is made between outside air intro-
duction and inside air recirculation.
When inside air is recirculated, the indi-
cator lamp comes on.
(Outside position)
Outside air is introduced into the pas-
senger compartment.
(Recirculation position)
Air is recirculated inside the passen-
ger compartment.
NOTE
Normally, use the outside position to keep
the windscreen and side windows clear and
quickly remove fog or frost from the wind-
screen.
If high cooling performance is desired, or
if the outside air is dusty or otherwise con-
taminated use the recirculation position.
Switch to the outside position periodically
to increase ventilation so that the win-
dows do not become fogged up.
CAUTION
Use of the recirculation position for
extended time may cause the win-
dows to fog up.
H03B062A
LHDLeg area heating
EH03BABe
Set the mode selection dial to the posi-
tion shown in the illustration and set the air
selection switch (A) to the outside posi-
tion.
Adjust the temperature by turning the tem-
perature control dial clockwise or anticlock-
wise.
Select the desired blower speed.
NOTE
When the maximum heating is needed, set
the blower speed at 3rd position.
For pleasant driving
6-38Div:
Out put date:

H03H024A
LHDDemisting of the windscreen and
door windows
EH03DAJg
CAUTION
For safety, make sure you have a
clear view through all windows.
To remove frost or mist from the wind-
screen and door windows, use the mode
selection dial (“
”or“
”).
H03H023A
RHD
- To keep the windscreen and door
windows clear of mist, and to keep
leg area heating (when driving in
rain or snow).
1- Set the air selection switch (A) to the
outside position.
2- Set the mode selection dial to the“
”
position.
3- Select the desired blower speed by turn-
ing the blower speed selection dial.
4- Select the desired temperature by turn-
ing the temperature control dial.
5- Push the air conditioning switch (B).
(vehicles with air conditioning)
H03D113A
LHD
- For quick demisting
1- Set the air selection switch (A) to the
outside position.
2- Set the mode selection dial to the“
”
position.
3- Set the blower speed to the maximum
speed position.
4- Set the temperature to the maximum
temperature position.
5- Push the air conditioning switch (B).
(vehicles with air conditioning)
For pleasant driving
6-40Div:
Out put date: