2003 MERCEDES-BENZ CL600 door lock

139 Controls in detail
Control system
Vehicle submenu
Access the
VEHICLE
submenu via the
SET-
INGS
menu. Use the
VEHICLE
submenu to
make general vehicle settings. The follow-
ing functions are available:
Setting station selection mode
Use the
STATION SEARCH USING
function
to select the manual or memory station se-
lection mode for the radio (
page 122).

Move the selection marker with
the
æ
or
ç
button to the
VEHI-
CLE
submenu.

Press button
j
or
k
repeatedly
until you see this message in the dis-
play:
STATION SEARCH USING
.
The selection marker is on the current
setting.

Press
æ
or
ç
to select the de-
sired station selection mode. You can
select:


FREQUENCY


MEMORY
selects next stored station
Setting automatic locking
Use this function to activate or deactivate
the automatic central locking. With the au-
tomatic central locking system activated,
the vehicle is centrally locked at vehicle
speeds of approximately 9 mph
(15 km/h).

Move the selection marker with
the
æ
or
ç
button to the
VEHI-
CLE
submenu.

Press button
j
or
k
repeatedly
until you see this message in the dis-
play:
AUTOMATIC DOOR LOCK
.
The selection marker is on the current
setting.

Press
æ
or
ç
to switch
AUTOMATIC DOOR LOCK
ON or
OFF
.
Function
Page
Set station selection mode
(radio)
see
below
Set automatic locking
139

141 Controls in detail
Control system
After entering the vehicle, the steering
wheel and seat will move into the position
stored in memory when

the driver’s door is closed


you put the key in the starter switch


press the appropriate stored position
button on the memory switch
(page 105).

Move the selection marker with
the
æ
or
ç
button to
the
CONVENIENCE
submenu.

Press button
j
or
k
repeatedly
until you see this message in the dis-
play:
EASY-ENTRY FEATURE ACTIVATE
.
The selection marker is on the current
setting.

Press
æ
or
ç
to change the
easy-entry / exit setting.
The following settings are available for the
easy-entry / exit feature:
Warning!
G
You must make sure that no one can be-
come trapped or injured by the moving
steering wheel and the driver’s seat when
the easy-entry / exit feature is in operation
and the driver’s door is being opened or the
key is removed from the starter switch. Do
not leave children unattended in the vehicle,
or with access to an unlocked vehicle. Unsu-
pervised use of vehicle equipment may
cause an accident and / or serious personal
injury.
Do not leave children unattended in the ve-
hicle, or with access to an unlocked vehicle.
Children could open the driver’s door and
unintentionally activate the easy-entry / exit
feature, which could result in an accident
and / or serious personal injury.
iTo cancel seat / steering wheel move-
ment, do one of the following:

Press seat adjustment switch
(page 35)


Move the steering column stalk
(page 37)


Press the memory switch
(page 105)
OFF
The
easy-entry / exit
feature is deactivat-
ed.
STEER. COL.
Only the steering
column is moved.
ST. COL + SEAT
Both the steering
column and the
seat are moved.

152 Controls in detailGood visibilityActivating exterior rear view mirror
parking position
The buttons are located on the driver’s
door.
1Driver’s side exterior rear view mirror
2Passenger-side exterior rear view
mirror
Follow these steps to activate the mirror
parking position so that the passen-
ger-side exterior rear view mirror will be
turned downward to the stored position.
Make sure you have stored a parking
position for the passenger-side exterior
rear view mirror (
page 107).

Make sure that the
MIRROR SETTING
WHEN PARKING
function in the
CONVENIENCE
submenu in the control
system, is switched to
ON (page 142).

Switch on ignition (if not already on).

Press button2 for passenger-side ex-
terior rear view mirror.

Place the gear selector lever in reverse
gear R.
The passenger-side exterior rear view
mirror will be turned downward in the
stored position.
The exterior rear view mirror returns to its
previously stored driving position:


10 seconds after you put the gear se-
lector lever out of position R


immediately once you exceed a vehicle
speed of approx. 6 mph (10 km/h)


immediately when you press button1
for driver’s side exterior rear view
mirrorElectrically folding exterior rear view
mirrors
Folding the exterior rear view mirrors in
and out automatically
When the corresponding function in the
control system is activated (
page 142):


The exterior rear view mirrors automat-
ically fold in as soon as the vehicle is
locked from the outside.


The exterior rear view mirrors automat-
ically fold out as soon as the vehicle is
unlocked and the driver’s or passenger
door are subsequently opened.

154 Controls in detailGood visibilityWindshield wipers
Information on the windshield wipers is
found in the “Getting started” section
(page 47).
A rain sensor automatically controls the
windshield wipers depending on how wet
the windshield is.

Switch on ignition.

Set the wiper switch to position I
(page 47).
After the initial wipe, pauses between
wipes are automatically controlled by the
rain sensor which monitors the wetness of
the windshield.
Headlamp cleaning system
The switch is located on the left side of the
dashboard.
1Headlamp washer switch
Switch on ignition.

Press switch1.
iIntermittent wiping is interrupted when
the vehicle is at a standstill and a front
door is opened.
!To prevent the windshield wipers from
being damaged, do not leave the wiper
switch in intermittent setting when the
vehicle is taken to an automatic car
wash or when cleaning the windshield.
The switch should not be left in inter-
mittent setting as the wipers will wipe
the windshield once every time the en-
gine is started. Dust that accumulates
on the windshield might scratch the
glass when wiping occurs on a dry
windshield. iIf intermittent wiping is on and you turn
the key in the steering lock from posi-
tion 1 to position 2 (
page 31) and
keep the key in that position longer
than 2 seconds, the wipe interval will
be set to approx. 5 seconds.

169 Controls in detail
Power windows
Power windows
Opening and closing the windows
The side windows can be opened and
closed electrically. The switches for all the
side windows are on the driver’s door. The
switches for the respective windows are
on the passenger door and on the rear cen-
ter console.
1Left front window
2Right front window
3Right rear window
4Left rear windowAdditional switches for the rear windows
are located on the rear center console.
1Left rear window
2Right rear window
Warning!
G
When closing the windows, make sure that
there is no danger of anyone being harmed
by the closing procedure.
The closing of the door windows can be im-
mediately halted by releasing the switch or,
if switch was pressed past the resistance
point and released, by pressing the respec-
tive switch.
If the window encounters an obstruction
t h a t b l o c k s i t s p a t h i n a c i r c u m s t a n c e w h e r e
you pressed the switch past the resistance
point and released it to close the window,
the automatic reversal function will stop the
window and open it slightly.
If the window encounters an obstruction
t h a t b l o c k s i t s p a t h i n a c i r c u m s t a n c e w h e r e
you are closing the window by pressing and
holding the switch, by pressing and holding
button
‹
on the SmartKey, or by press-
ing and holding the lock button
(vehicles with KEYLESS-GO*) on the door
handle, the automatic reversal function will
not operate.
When leaving the vehicle, always remove the
key from starter switch, take the SmartKey
with KEYLESS-GO* with you, and lock your
vehicle. Do not leave children unattended in
the vehicle, or with access to an unlocked
vehicle. Unsupervised use of vehicle equip-
ment can cause an accident and/or serious
personal injury.

170 Controls in detailPower windows
Turn key in the starter switch to
position1 or2.
Opening the windows

Lightly press switch
k
to resistance
point.
The window will move downwards until
you release the switch.
Closing the windows

Lightly press switch
j
to resistance
point.
The window will move upwards until
you release the switch.
If you pull and hold the switch up when
closing the window, and upward move-
ment of the window is blocked by some
obstruction including but not limited to
arms, hands, fingers etc., the automat-
ic reversal will not operate.Fully opening the windows

Press switch
k
past the resistance
point and release.
Fully closing the windows

Press switch
j
past the point of re-
sistance and release.
!If the upward movement of the window
is blocked during the closing proce-
dure, the window will stop and open
slightly.
Remove the obstruction, press the
switch
j
again past the resistance
point and release.
If the window still does not close when
there is no obstruction, then hold the
switch
j
down. The side window
will then close without the obstruction
sensor function.
Warning!
G
Driver's door only:
If within five seconds you again press the
switch past the resistance point and re-
lease, the automatic reversal will not func-
tion.

172 Controls in detailPower windowsClosing the side windows and sliding /
pop-up roof with KEYLESS-GO*
Press and hold lock button at door
(page 52) until the side windows and
the sliding / pop-up roof are closed.
Synchronizing power windows
The power windows must be resynchro-
nized each time after the battery has been
disconnected:
Push the power window switches until
the side windows are closed and hold
the switches for approximately one
second.
Warning!
G
When closing the windows and the sliding /
pop-up roof, make sure that there is no dan-
ger of anyone being harmed by the closing
procedure.
The windows will not automatically re-open
if blocked during convenience closing.
If potential danger exists, proceed as fol-
lows:
SmartKey

Release the
‹
button.


Press and hold the
Œ
button until
the windows and the sliding / pop-up
roof open again.
KEYLESS-GO*


Release the lock button.


Pull on the door handle and hold firmly.
The side windows and the
sliding / pop-up roof will open for as long
as the door handle is held but the door
not opened.

174 Controls in detailSliding / pop-up roofOpening the sliding / pop-up roof auto-
matically
To select a sunroof opening position,
press the switch to the resistance point
and release it when the sunroof has
reached the required position.
The sliding / pop-up roof now opens to
the position set if the switch is pressed
past the resistance point in the “open”
direction.
Closing the sliding / pop-up roof auto-
matically

Press the switch past the resistance
point in the “close” direction and re-
lease.
The sliding / pop-up roof closes com-
pletely.
Stopping the sliding / pop-up roof

Move the switch in any direction.If the movement of the sliding / pop-up
roof is blocked during the closing pro-
cedure, the roof will stop and reopen
slightly.Opening and closing the sliding /
pop-up roof with the SmartKey
The power windows will also be opened or
closed when you operate the sliding /
pop-up roof with the key.

Aim transmitter eye at the front door
handle.
iYou can also open or close the sliding /
pop-up roof using the:

SmartKey (
page 171)


button
O
in the control panel of
the automatic climate control
(
page 159)


button
e
in the control panel of
the automatic climate control
(
page 159)
!To avoid damaging the seals, do not
transport any objects with sharp edges
which can stick out of the sliding /
pop-up roof.
The sliding / pop-up roof can be opened
or closed manually should an electrical
malfunction occur (
page 301).
Warning!
G
Never operate the windows or sliding /
pop-up roof if there is the possibility of any-
one being harmed by the opening or closing
procedure.
In case the procedure causes potential dan-
ger, the procedure can be stopped immedi-
ately by releasing the remote control button.
To reverse direction of movement,
press
Œ
for opening or
‹
for closing