2003 Lexus IS300 Basic Functions / LEXUS 2003 IS300 OWNER'S MANUAL (OM53439U)

IN CASE OF AN EMERGENCY
276
CAUTION
SportCross:
The spare tire was designed especially for your
Lexus. Do not use it on any other vehicle.
 Do not use more than one spare tire at the same time.
 Do not exceed 80 km/h (50 mph) when driving with the
spare tire.
 The standard tire should be repaired and replaced as
soon as possible.
 Avoid sudden acceleration, sudden deceleration and
sharp turns with the spare tire.
Changing procedure
SV41027

1Jack 2Jack handle 3Wrench 4 Spare tire
1. Get the jack, wrench and spare tire.
To prepare yourself for an emergency, you should familiarize
yourself with the use of the jack and each tool, and their
storage locations.
2003 IS300 from Aug. '02 Prod. (OM53439U)

IN CASE OF AN EMERGENCY
277
SS41005

1Joint
2When removing the jack, turn the joint by hand in the
ºcontractº direction until the jack is free.
3 When storing, turn the joint by hand in the ºexpandº
direction u ntil the jack is firmly secured to prevent it from
flying forward during a collision or sudden braking.
SV41028
To remove the spare tire:
1Remove the tool tray
2Loosen the bolt and remove it.
When storing the spare tire, place it with the inner side of the
wheel facing up. Then bolt the tire in place and install the tool
tray to prevent the tire from flying forward during a collision or
sudden braking.
2003 IS300 from Aug. '02 Prod. (OM53439U)

IN CASE OF AN EMERGENCY
278
SV41033
2. Block the wheel diagonally opposite the flat tire to keep
the vehicle from rolling when it is jacked up.
When blocking the wheel, place a wheel block in front of one
of the front wheels or behind one of the rear wheels.
SS41008
3. Loosen all the wheel nuts.
Always loosen the wheel nuts before raising the vehicle.
Turn the wheel nuts counterclockwise to loosen them. To get
maximum leverage, fit the wrench to the nut so that the handle
is on the right side, as shown above. Grab the wrench near the
end of the handle and pull up on the handle. Be careful that the
wrench does not slip off the nut.
Do not remove the nuts yet ± just unscrew them about one±half
turn.
CAUTION
Never use oil or grease on the bolts or nuts. The nuts
may loosen and the wheels may fall off, which could
cause a serious accident.
2003 IS300 from Aug. '02 Prod. (OM53439U)

IN CASE OF AN EMERGENCY
279
SV04003
4. Position the jack at the jack points as shown.
Make sure the jack is positioned on a level and solid surface.
SV41031
5. After making sure no one is in the vehicle, raise it high
enough so that the spare tire can be installed.
Allow for the fact that you need more ground clearance when
putting on the spare tire than when removing the flat tire.
To raise the vehicle, insert the jack handle into the jack (it is a
loose fit) and turn it clockwise. As the jack touches the vehicle
and begins to lift, double±check that it is properly positioned.
CAUTION
Never get under the vehicle when the vehicle is
supported by the jack alone.
2003 IS300 from Aug. '02 Prod. (OM53439U)

IN CASE OF AN EMERGENCY
280
SS41011
6. Remove the wheel nuts and remove the flat tire.
Lift the flat tire straight off and put it aside.
SL41003
7. Remove the wheel ornament.
When installing the alloy wheels, at this point, remove the
wheel ornament from the flat tire and replace it on the newly
installed tire.
SS41012
Before putting on the wheel, remove any corrosion on the
mounting surfaces with a wire brush or such. Installation of
wheels without good metal±to±metal contact at the mounting
surface can cause wheel nuts to loosen and eventually cause
a wheel to come off while driving.
2003 IS300 from Aug. '02 Prod. (OM53439U)

IN CASE OF AN EMERGENCY
281
SS41013
8. Reinstall all the wheel nuts finger tight.
Align the holes in the wheel with the bolts. Then lift up the
wheel and get at least the top bolt started through its hole.
Wiggle the tire and press it back over the other bolts.
Reinstall the wheel nuts and tighten them as much as you can
by hand. Press the tire back and see if you can tighten them
more.
CAUTION
Never use oil or grease on the bolts or nuts. Doing so
may lead to overtightening the nuts and damaging the
bolts. The nuts may loosen and the wheels may fall off,
which could cause a serious accident. If there is oil or
grease on any bolt or nut, clean it.
SS41014
9. Lower the vehicle completely and tighten the wheel
nuts.
Turn the jack handle counterclockwise to lower the vehicle.
Use only the wheel nut wrench to tighten the nuts. Do not use
other tools or any additional leverage other than your hands,
such as a hammer, pipe or your foot. Make sure the wrench
is securely engaged over the nut.
Tighten each nut a little at a time in the order shown. Repeat
the process until all the nuts are tight.
CAUTION
 When lowering the vehicle, make sure all portions of
your body and all other persons around will not be
injured as the vehicle is lowered to the ground.
 As soon as possible after changing wheels, have the
wheel nuts tightened by torque wrench at 103 N´m
(10.5 kgf´m, 76 ft´lbf.).
2003 IS300 from Aug. '02 Prod. (OM53439U)

IN CASE OF AN EMERGENCY
282
SL41002
10. Reinstall the wheel ornament.
Put the wheel ornament into position and then tap it firmly with
the side or heel of your hand to snap it into place.
CAUTION
Take due care in handling the ornament to avoid
unexpected personal injury.
11. After changing the wheel, check the air pressure of the
replaced tire. Stow all the tools, jack and flat tire securely.
If the pressure of the replaced tire is low, drive slowly to the
nearest service station and fill to the correct pressure.
Do not forget to reinstall the tire valve cap as dirt and moisture
could get into the valve core and possibly cause air leakage.
If the cap is missing, put a new one on as soon as possible.
This is the same procedure for changing or rotating your tires.
CAUTION
 When reinstalling a standard tire, take due care in
handling the ornament to avoid unexpected personal
injury.
 Before driving, make sure all the tools, jack and flat
tire are securely in place in their storage location to
reduce the possibility of personal injury during a
collision or sudden braking.
2003 IS300 from Aug. '02 Prod. (OM53439U)

IN CASE OF AN EMERGENCY
283
IF YOUR VEHICLE BECOMESSTUCK
If your vehicle becomes stuck in snow, mud, sand, etc.,
then you may attempt to rock the vehicle free by moving
it forward and backward.
Your vehicle is equipped with the traction control system,
turn off the system to become unstuck to allow the tires
to spin enough to remove the vehicle from the
obstruction. (For details, see ºTraction control systemº
on page 244 or 246.)
CAUTION
Do not attempt to rock the vehicle free by moving it
forward and backward if people or objects are anywhere
near the vehicle. During the rocking operation the
vehicle may suddenly move forward or backward as it
becomes unstuck, causing injury or damage to nearby
people or objects.
NOTICE
If you rock your vehicle, observe the following precautions to prevent damage to the transmission and
other parts.
Do not depress the accelerator pedal while shifting the selector lever or before the transmission iscompletely shifted to forward or reverse gear.
Do not race the engine and avoid spinning thewheels.
If your vehicle remains stuck after rocking the vehicleseveral times, consider other ways such as towing.
2003 IS300 from Aug. '02 Prod. (OM53439U)