2003 HONDA CIVIC HATCHBACK lock

µCheck your tires
f requently f or wear and proper
pressure. Both are important in
preventing ‘‘hydroplaning’’ (loss of
traction on a wet surface). In the
winter, mount snow tires on all f our
wheels f or the best handling.
Watch road conditions caref ully,
they can change f rom moment to
moment. Wet leaves can be as slip-
pery as ice. ‘‘Clear’’ roads can have
patches of ice. Driving conditions
can be very hazardous when the
outside temperature is near f reezing.
The road surf ace can become
covered with areas of water puddles
mixed with areas of ice, so your
traction can change without warning.
Be caref ul when downshif ting. If
traction is low, you can lock up the
drive wheels f or a moment and cause
askid. Be very cautious when passing, or
beingpassedbyothervehicles.The
spray f rom large vehicles reduces
your visibility, and the wind buf f eting
can cause you to lose control.Your car is not designed to tow a
trailer. Attempting to do so can void
your warranties.
Traction
Towing a Trailer
Driving
Driving in Bad Weather, Towing a Trailer
152

µ
Î ÌÌÌ
Î
Maint enance
160 Service at the indicated distance or time whichever comes first. miles x
1,000
km x 1,000
months
Service the following items at the recommended intervals.
Every 110,000 miles (176,000 km)
Inspect every 110,000 miles (176,000 km), otherwise adjust only if noisy
At 120,000 miles (192,000 km) or 10 years,
then every 60,000 miles (96,000 km) or 5 years Every 3 years (independent of mileage)
See dust and pollen filter on page for replacement information under special driving conditions.
See information on maintenance and emissions warranty, last column, page . Check oil and coolant at each fuel stop
Every 15,000 miles (24,000 km) in dusty conditions, otherwise use normal schedule
Replace every 5,000 miles (8,000 km) or 6 months
Check engine oil and coolant
Replace engine oil
Rotate tires (Check tire inflation and condition at least once per month)
Replace engine oil filter
Inspect front and rear brakes
Lubricate all hinges, locks, and latches
Visually inspect the following items:
Tie rod ends, steering gear box and boots
Suspension components
Driveshaft boots
Check parking brake adjustment
Visually inspect the following items: Brake hoses and lines (including ABS)
All fluid levels and condition of fluidsExhaust system, Fuel lines and connections
Lights and controls, Vehicle underbody
Inspect and adjust drive belts
Replace dust and pollen filter
Replace transmission fluid
Replace air cleaner element
Replace spark plugs
Inspect valve clearance
Inspect idle speed
Replace engine coolant
Replace brake fluid 10 16
203230484064 5080609670
112 80
128 90
144 100160110176120192
Every 160,000 miles (256,000 km) or 8 years 24 48 72
12 36 60
:: 157
190
Maintenance Schedule for Severe Conditions

µµ
Ø Ø Ø ØØØØØØØØØØ Ø ØØØØØØ
ÌÌ
Î
Î Ì
CONT INUED
Maint enance 161
U.S. Owners
Canadian Owners
A, B, C, D, E
AB C D E
Refer to page to determine which schedule to use.
Use the Maintenance Schedule for Severe Conditions.
Service at the indicated distance or time, whichever comes first. Do the items in as required for each distance/time.
5,000 mi/8,000 km/6 mos
10,000 mi/16,000 km/1 yr
15,000 mi/24,000 km
15,000 mi/24,000 km/1-½yrs
20,000 mi/32,000 km/1 yr
25,000 mi/40,000 km/2 yrs
30,000 mi/48,000 km
30,000 mi/48,000 km/2 yrs
35,000 mi/56,000 km/2-½yrs
40,000 mi/64,000 km/2 yrs
45,000 mi/72,000 km
45,000 mi/72,000 km/3 yrs
3yrs
50,000 mi/80,000 km/3 yrs
55,000 mi/88,000 km/3-½yrs
60,000 mi/96,000 km
60,000 mi/96,000 km/3 yrs
65,000 mi/104,000 km/4 yrs
70,000 mi/112,000 km/4 yrs
75,000 mi/120,000 km
75,000 mi/120,000 km/4-½yrs
80,000 mi/128,000 km/4 yrs
85,000 mi/136,000 km/5 yrs
90,000 mi/144,000 km
90,000 mi/144,000 km/5 yrs
95,000 mi/152,000 km/5-½yrs
100,000 mi/160,000 km/5 yrs
105,000 mi/168,000 km
105,000 mi/168,000 km/6 yrs Do item in A.
Do items in A, B.
Do item in E.
Do item in A.
DoitemsinA,B,C.
Do item in A.
Do item in E.
DoitemsinA,B,D.
Do item in A.
DoitemsinA,B,C.
Do item in E.
Do item in A.
Replace brake fluid (independent of mileage).
Do items in A, B.
Do item in A.
Do item in E.
Replace transmission fluid.
DoitemsinA,B,C,D.
Do item in A.
Do items in A, B.
Do item in E.
Do item in A.
DoitemsinA,B,C.
Do item in A.
Do item in E.
DoitemsinA,B,D.
Do item in A.
Do item in A, B, C.
Do item in E.
Do item in A. Replace engine oil.
Replace engine oil filter.
Inspect front and rear brakes.
Rotate tires (follow pattern on page 196 ).
Lubricate all hinges, locks, and latches.
Inspect tie rod ends, steering gear box and boots.
Inspect suspension components.
Inspect driveshaft boots.
Check parking brake adjustment.
Inspect brake hoses and lines (including ABS).
Check all fluid levels, condition of fluids, and check
for leaks.
Inspect exhaust system.
Inspect fuel lines and connections.
Check all lights.
Inspect the underbody.
Inspect and adjust drive belts.
Replace dust and pollen filter .
Replace air cleaner element every 15,000 mi/
24,000 km (independent of time) under dusty
conditions, otherwise use Normal Conditions
schedule.
156
Check engine oil and coolant at each fuel stop.
Check and adjust valve clearance, cold engine, only if noisy.See information on maintenance and emissions warranty, last
column, page .
See dust and pollen filter on page for replacement information
under special driving conditions.
157
NOTE: : :
190
Maintenance Schedule for Severe Conditions (listed by distance/time)

Remove the radiator cap by
pushing down and turning
counterclockwise.
Turn the radiator cap counter-
clockwise, without pressing down
on it, until it stops. This relieves
any pressure remaining in the
cooling system.
Make sure the engine and radiator
are cool.
The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.Do not add any rust inhibitors or
other additives to your car’s cooling
system. They may not be compatible
with the coolant or engine compo-
nents.
Pour coolant into the reserve tank.
Fill it to half way between the MAX
and MIN marks. Put the cap back
on the reserve tank.
Pourthecoolantslowlyand
caref ully so you do not spill. Clean
up any spills immediately. Spilled
coolant could damage components
in the engine compartment.
Put the radiator cap back on.
Tighten it f ully.
2. 3. 4. 5.6.
1. Maint enance
Cooling Syst em
172RADIATOR CAP
RESERVE TANK

Loosen the drain plug on the
bottom of the radiator. Drain the
coolant into an appropriate
container.Disengage the holding clip at the
bottom of the reserve tank.
Remove the drain cap and install a
rubber hose. Drain the coolant
into an appropriate container.
When the coolant stops draining,
tightenthedrainplugatthe
bottom of the radiator.
Remove the rubber hose and
reinstall the drain cap securely.Tighten the drain cap with the
holding clip securely.
Put the cover back in place and
tighten the bolts securely.
Reinstall the nine holding-clips and
lock each clip in place by pushing
on its center.
6. 7.
4.
5.8.
9.
Maint enance
Cooling Syst em
174 DRAIN PLUG
DRAIN CAP
HOLDING CLIP

Torque the spark plug. (If you do
not have a torque wrench, tighten
the spark plug two-thirds of a turn
af ter it contacts the cylinder head.)
Tightening torque:
Put the new spark plug into the
socket, then screw it into the hole.
Screw it in by hand so you do not
crossthread it.
Remove the spark plug with a 16
mm (f ive-eighths inch) spark plug
socket.
Remove the ignition coil.
Disconnect the wire connector
f rom the ignition coil by pushing
on the lock tab and pulling on the
connector. Pull on the plastic
connector, not the wires.
Use a wrench to remove the bolt
holding the ignition coil. Pull the
ignition coil up slightly.
8.
7.
6.
3. 4. 5.
Spark Plugs
Maint enance
182 BOLT CONNECTOR
IGNITION COIL LOCK TAB
13 lbf·ft (18 N·m , 1.8 kgf·m)

Install the ignition coil into the
hole.
Connect the wire connector to the
ignition coil. Make sure it locks in
place.Push the ignition coil down all the
way. Install the bolt.
Repeat this procedure f or the
other three spark plugs.
Reinstall the coil cover, and
tighten the f our nuts.
Tightening torque:
NGK:
DENSO:
9.
10. 13.
12.
11.
Specif ications:
Maint enance
Spark Plugs
183
7 lbf·ft (9.8 N·m , 1.0 kgf·m)
IZFR6K-11SKJ20DR-M11
Tighten the spark plugs caref ully. A
spark plug that is too loose can
overheat and damage the engine.
Overtightening can cause damage to
the threads in the cylinder head.

Disconnect the blade assembly
fromthewiperarmbypushingin
the lock tab. Hold the lock tab in
while you push the blade assembly
toward the base of the arm.
Raise the wiper arm of f the
windshield.
Check the condition of the wiper
blades at least every six months.
Look f or signs of cracking in the
rubber, or areas that are getting
hard. Replace the blades if you f ind
these signs, or if they leave streaks
and unwiped areas when used.
To replace a f ront wiper blad:Raise the driver’s side f irst, then
the passenger’s side. 2.
1.
Wiper Blades
Maint enance
186 WIPER ARMS
LOCK TAB