2003 FORD MUSTANG ECO mode

PINPOINT TEST G: THE ANTI - THEFT SYSTEM DOES NOT OPERATE Test Step Result / Action to Take
NOTE:
Large metallic objects, electronic debit transponder devices or a second key on the same
key ring as the PATS ignition key may cause vehicle starting problems and record DTCs under
certain conditions. If a fault cannot be identified, examine the customer's key for such objects or
devices. If present, inform the customer that they need to keep these objects from touching the
PATS ignition key while starting the engine. These objects and devices cannot damage the
PATS ignition key, but can cause a momentary problem if they are too close to the key during
engine start. If a problem occurs, turn ignition OFF and restart the engine with all other objects
on the key ring held away from the ignition key. Check to ensure the encoded ignition key used
by the customer is an approved Ford encoded ignition key (encoded ignition keys from Rotunda,
Ilco, Curtis, or Strattec are approved Ford encoded ignition keys). F1 USE THE DTCS FROM THE INSTRUMENT
CLUSTER SELF- TESTS z
Use the recorded results from the Instrument
Cluster Continuous and On- Demand Self-Tests.
z Is DTC B1600 retrieved? Yes
GO to
F2 .
No
If other DTCs are retrieved, REFER
to Instrument Cluster Diagnostic
Trouble Code (DTC) Index.
If no DTCs are retrieved, system is
OK. F2 PROGRAM A NEW ENCODED IGNITION KEY
z
Key in OFF position.
z NOTE: Check to make sure the customer and
replacement encoded ignition keys are approved
Ford encoded PATS ignition keys. Unapproved
PATS keys do not always operate correctly over
different temperature ranges (encoded ignition
keys from Rotunda, Ilco, or Strattec are approved
encoded ignition keys).
z Cut a new encoded ignition key.
z Key in ON position.
z Program the new encoded ignition key; for
additional information, refer to Key Programming — Erase All Key Codes and Program
Two Keys .
z Enter the following diagnostic mode on the
diagnostic tool: Instrument Cluster On- Demand
Self- Test.
z Is DTC B1600 still present? Yes
GO to
F3 .
No
If no other DTCs are retrieved,
system is OK.
If other DTCs are retrieved, REFER
to Instrument Cluster Diagnostic
Trouble Code (DTC) Index. F3 INSTALL A NEW PATS TRANSCEIVER
z
Key in OFF position.
z Install a new PATS transceiver; for additional
information, refer to Module — Passive Anti - Theft
Transceiver .
z Key in ON position.
z NOTE: Use the customer's original encoded
ignition key, not the encoded ignition key that was
cut in the previous step.
z Enter the following diagnostic mode on the
diagnostic tool: Instrument Cluster On- Demand
Self- Test.
z Is DTC B1600 retrieved? Yes
INSTALL a new instrument cluster;
for additional information, REFER to
Section 413
- 01 . CYCLE the ignition
to RUN using two encoded ignition
keys. Go To Pinpoint Test J to
initialize the module. REPEAT the
self- test. CLEAR the DTCs.
No
System is OK. Klj . 9 ba
182003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST H: THE ANTI-
THEFT SYSTEM DOES NOT OPERATE
CORRECTLY — PATS RECEIVED INVALID FORMAT OF KEY- CODE
FROM IGNITION KEY TRANSPONDER (PARTIAL KEY READ) Key Programming to enable the PID SPARE KEY to
ENABLE. TEST the system for normal operation.
Once completed, GO to G5 .
G5 CHECK THE ENCODED IGNITION
KEYS FOR CORRECT OPERATION z
Key in OFF position.
z Key in ON position.
z Start the vehicle using the first
encoded ignition key.
z Key in ON position.
z Start the vehicle with the second
ignition key.
z Key in OFF position.
z Does the vehicle start correctly
using both encoded ignition
keys? Yes
System is OK. If there are additional keys that need to
be programmed, for additional information, REFER to
Key Programming
— Program a Key Using Two
Programmed Keys .
No
GO to G6 .
G6 RETRIEVE THE INSTRUMENT
CLUSTER DTCS — CHECK FOR DTC
B1601 z
Retrieve and document
continuous DTCs.
z Enter the following diagnostic
mode on the diagnostic tool:
Clear Continuous DTCs.
z Carry out a instrument cluster
self- test using both ignition keys
from Step G5.
z Is DTC B1601 retrieved? Yes
INSTALL a new instrument cluster; for additional
information, REFER to
Section 413 - 01 . CYCLE the
ignition to RUN using two encoded ignition keys. GO
to Pinpoint Test J to initialize the vehicle. REPEAT the
self- test. CLEAR the DTCs.
No
System is OK.
If other DTCs are retrieved, REFER to Instrument
Cluster Module Diagnostic Trouble Code (DTC) Index. Test Step Result / Action to Take
NOTE:
Large metallic objects, electronic debit transponder devices or a second key on the same
key ring as the PATS ignition key may cause vehicle starting problems and record DTCs under
certain conditions. If a fault cannot be identified, examine the customer's key for such objects or
devices. If present, inform the customer that they need to keep these objects from touching the
PATS ignition key while starting the engine. These objects and devices cannot damage the
PATS ignition key, but can cause a momentary problem if they are too close to the key during
engine start. If a problem occurs, turn ignition OFF and restart the engine with all other objects
on the key ring held away from the ignition key. Check to ensure the encoded ignition key used
by the customer is an approved Ford encoded ignition key (encoded ignition keys from Rotunda,
Ilco, Curtis, or Strattec are approved Ford encoded ignition keys). H1 USE THE DTCS FROM THE
INSTRUMENT CLUSTER SELF TESTS z
Use the recorded results from the
Instrument Cluster Continuous and
On- Demand Self- Tests.
z Is DTC B1602 retrieved? Yes
GO to
H2 .
No
System is OK. CHECK all customer encoded
ignition keys with Instrument Cluster On- Demand
Self- Test to verify all other keys are programmed. Klj . 11 ba
182003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST I: THE ANTI-
THEFT SYSTEM DOES NOT OPERATE
CORRECTLY — PATS TRANSCEIVER SIGNAL IS NOT RECEIVED
(NOT CONNECTED, DAMAGED, OR WIRING) H2 OBTAIN A NEW ENCODED
IGNITION KEY z
Key in OFF position.
z Cut a new encoded ignition key.
z Key in ON position.
z Program a new encoded ignition
key; for additional information, refer
to Key Programming — Erase All Key
Codes and Program Two Keys .
z Enter the following diagnostic mode
on the diagnostic tool: Instrument
Cluster On- Demand Self- Test.
z Is DTC B1602 retrieved? Yes
GO to
H3 .
No
System is OK. If the customer has any remaining
encoded keys at home, instruct them to carry out
Key Programming — Program a Key Using Two
Programmed Keys on each remaining key. This
procedure is detailed in the Owners Guide. H3 INSTALL A NEW PATS
TRANSCEIVER z
Key in OFF position.
z Install a new PATS transceiver; for
additional information, refer to
Module — Passive Anti - Theft
Transceiver .
z Key in ON position.
z Enter the following diagnostic mode
on the diagnostic tool: Instrument
Cluster On- Demand Self- Test.
z Are any DTCs retrieved? Yes
REFER to Instrument Cluster Diagnostic Trouble
Code (DTC) Index.
No
System is OK.
Test Step Result / Action to Take
I1 USE THE DTCS FROM THE INSTRUMENT CLUSTER
SELF TESTS z
Use the recorded results from the Instrument Cluster
Continuous and On- Demand Self-Tests.
z Is DTC B1681 retrieved? Yes
GO to
I2 .
No
System is OK. I2 CHECK THE PATS TRANSCEIVER FOR VOLTAGE —
CIRCUIT 20 (WH/LB) z
Key in OFF position.
z Disconnect: PATS Transceiver C252.
z Key in ON position.
z Measure the voltage between PATS transceiver C252
Pin 2, Circuit 20 (WH/LB), harness side and ground. Yes
GO to
I3 .
No
REPAIR Circuit 20 (WH/LB).
REPEAT the self- test. CLEAR
the DTCs. Klj . 12 ba
182003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST J: THE ANTI-
THEFT SYSTEM DOES NOT OPERATE
CORRECTLY — PCM ID DOES NOT MATCH BETWEEN
INSTRUMENT CLUSTER AND PCM PINPOINT TEST K: THE ANTI - THEFT SYSTEM DOES NOT OPERATE If other DTCs are retrieved,
REFER to Instrument Cluster
Diagnostic Trouble Code (DTC)
Index.
Test Step Result / Action to Take
J1 USE THE DTCS FROM THE
INSTRUMENT CLUSTER SELF
TESTS z
Use the recorded results
from the Instrument
Cluster Continuous and
On- Demand Self- Tests.
z Is DTC B2139 recorded? Yes
GO to
J2 .
No
System is OK. J2 CLEAR PCM ID FROM
INSTRUMENT CLUSTER AND
PCM z
Carry out the security
access procedure for the
instrument cluster. For
additional information,
refer to Security Access —
Procedure .
z NOTE: DO NOT carry out
ignition key code erase.
z Select FSF card
PARAMETER RESET
command for instrument
cluster.
z Use diagnostic card for
PCM Active Command
Keep Alive Memory
Reset.
z Key in OFF position.
z Select FSF card
PARAMETER RESET
command for PCM.
z Key in ON position.
z Turn the ignition switch to
RUN for three seconds.
z Enter the following
diagnostic mode on the
diagnostic tool: Clear
Continuous DTCs.
z Key in OFF position.
z Enter the following
diagnostic mode on the
diagnostic tool: Retrieve
Continuous DTCs.
z Is DTC B2139 retrieved? Yes
VERIFY PCM calibration is correct for the vehicle. If correct,
REPEAT Step J2. If fault code persists, INSTALL a new
instrument cluster; for additional information, REFER to
Section 413
- 01 . CYCLE the ignition to RUN using two
encoded ignition keys. REPEAT Pinpoint Test J . CLEAR the
DTCs. TEST the system for normal operation. If DTC B2139
still exists, INSTALL a new PCM; for additional information,
REFER to Section 303 - 14 . REPEAT the self-
test. CLEAR the
DTCs.
No
System is OK. CHECK for any other DTCs. REFER to the
instrument cluster Diagnostic Trouble Code Index. Klj . 16 ba
182003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

CORRECTLY —
NVM CONFIGURATION FAILURE (NO PCM ID
EXCHANGED BETWEEN INSTRUMENT CLUSTER AND PCM) Test Step Result / Action to Take
K1 USE THE DTCS FROM
THE INSTRUMENT CLUSTER
SELF TESTS z
Use the recorded results
from the Instrument
Cluster Continuous and
On- Demand Self- Tests.
z Are any DTCs
recorded? Yes
If DTC B2141 only is retrieved, GO to
K2 .
If DTC U1147 is retrieved with DTC B2141, GO to Pinpoint Test C .
No
System is OK. K2 CARRY OUT KEEP ALIVE
MEMORY RESET FROM PCM z
Use diagnostic card for
PCM Active Command —
Keep Alive Memory
Reset.
z Key in OFF position.
z Key in ON position.
z Leave the key in the run
position for thirty
seconds.
z Key in OFF position.
z Start the vehicle.
z Does the vehicle start? Yes
System is OK.
No
GO to
K3 .
K3 RETRIEVE THE
INSTRUMENT CLUSTER
DTCS z
Enter the following
diagnostic mode on the
diagnostic tool: Clear
Continuous DTCs.
z Key in OFF position.
z Key in ON position.
z Key in OFF position.
z Enter the following
diagnostic mode on the
diagnostic tool:
Instrument Cluster On-
Demand Self- Test.
z Is DTC B2141 retrieved? Yes
REPEAT K2. If the fault persists, verify the PCM calibration. If
the calibration is OK, INSTALL a new instrument cluster. for
additional information, REFER to
Section 413 - 01 . Cycle the
ignition key to run using two encoded ignition keys. GO to
Pinpoint Test J to initialize the module. REPEAT the self-
test.
CLEAR the DTCs.
No
REFER to the DTC index. Klj . 17 ba
182003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

z
Is the resistance less than 5 ohms? D9 CHECK THE GEM CONTROL OF THE DRIVER POWER
WINDOW z
Key in ON position.
z Enter the following diagnostic mode on the diagnostic tool:
GEM Active Command FRONT WINDOW CONTROL.
z Trigger DR DOWN ON.
z Did the driver window move down? Yes
INSTALL a new GEM.
REFER to
Section 419 -
10 . TEST the system for
normal operation.
No
GO to D10 .
D10 CHECK THE WINDOW REGULATOR MOTOR OPERATION
z
Disconnect: Driver Window Regulator Motor C518.
z Connect a 20 amp fused jumper wire between battery positive
and one pin of the window regulator motor (component side).
z Momentarily connect a jumper wire between second pin of the
window regulator motor and ground.
z Reverse the jumper wires on the window regulator motor.
z Did the window regulator motor operate in both
directions? Yes
GO to
D11 .
No
INSTALL a new window
regulator motor. REFER
to Motor — Window
Regulator in this section.
TEST the system for
normal operation. D11 CHECK CIRCUIT 992 (WH/BK) FOR AN OPEN BETWEEN
THE DRIVER WINDOW MOTOR AND THE WINDOW
REGULATOR CONTROL SWITCH z
Disconnect: Driver Window Regulator Control Switch C537.
z Measure the resistance between driver window regulator
control switch C537 pin 6, circuit 992 (WH/BK), harness side
and driver window regulator motor C518, circuit 992 (WH/BK),
harness side. Yes
GO to
D12 .
No
REPAIR the circuit. TEST
the system for normal
operation. Klj . 12 ba
322003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

z
Are the resistances less than 5 ohms? E8 CHECK CIRCUIT 400 (LB/BK) FOR AN OPEN
z
Key in OFF position.
z Disconnect: CJB Circuit Breaker 43 (20A).
z Measure the resistance between driver window regulator control
switch C508 pin 10, circuit 400 (LB/BK), harness side and CJB
circuit breaker 43 (20A) output pin, circuit 400 (LB/BK).
z Is the resistance less than 5 ohms? Yes
REPAIR the power
supply to CJB circuit
breaker 43 (20A). TEST
the system for normal
operation.
No
REPAIR the circuit.
TEST the system for
normal operation.
E9 CHECK THE GEM CONTROL OF THE DRIVER POWER
WINDOW z
Key in ON position.
z Enter the following diagnostic mode on the diagnostic tool: GEM
Active Command FRONT WINDOW CONTROL.
z Trigger DR DOWN ON.
z Did the driver window move down? Yes
INSTALL a new GEM.
REFER to
Section 419 -
10 . TEST the system
for normal operation.
No
GO to E10 .
E10 CHECK THE WINDOW REGULATOR MOTOR OPERATION
z
Disconnect: Driver Window Regulator Motor C518.
z Connect a 20 amp fused jumper wire between battery positive
and one pin of the window regulator motor (component side).
z Momentarily connect a jumper wire between the second pin of Yes
GO to
E11 .
No Klj . 16 ba
322003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

GENERAL PROCEDURES
Programming —Keyless Entry Remote Transmitter
NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: All previous transmitter identification codes (TIC's) will be erased when programming mode is
entered.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the generic electronic
module (GEM)(14B204), perform the following steps.
1. Turn the ignition from OFF to RUN eight times within 10 seconds, ending in RUN. If the GEM has successfully entered program mode, it will lock and unlock all the doors.
2. NOTE: The first TIC must be entered within 7.5 seconds of entering the program mode and
additional TICs must be entered within 7.5 seconds of the first TIC. The programming mode is
exited whenever the timing constraints are not met.
Press any button on a keyless entry remote transmitter, and the doors will lock and then unlock
to confirm that each keyless entry remote transmitter has been programmed.
3. If the door locks do not respond for any keyless entry remote transmitter, wait for several seconds and press the button again.
4. Turn the ignition switch to the OFF position, or wait up to five minutes after step 1, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed),
the GEM will lock and unlock all the doors one last time.
SECTION 501-
14B: Keyless Entry/Computer Operated Locks 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...