2003 FORD MUSTANG air condition

end surface of the
power steering pump
rotor.
z Damaged or worn
power steering pump
rotor splines.
z A crack on the inner
surface of the power
steering pump cam.
z Interference between
the power steering
pump rotor and cam.
z Damaged or worn
power steering pump
rotor and pressure
plates. 02 .
z Power steering
pump swish noise z
Power steering fluid
flow into the bypass
valve of the pump
valve housing with fluid
temperature below 54°
C (130°F). z
Acceptable condition.
z Power steering
pump whine noise z
Aerated fluid. zPURGE the air from the
system. REFER to
Section 211 - 00 .
CHECK for a leak in the
system.
z Damaged power
steering pump cam. z
REPAIR or INSTALL a
new power steering
pump as necessary.
REFER to Section 211 -
02 .
z Damaged valve cover
O-ring seal. z
REPAIR or INSTALL a
new power steering
pump as necessary.
REFER to Section 211 -
02 .
z Power steering
pump clicking
(mechanical) noise z
Power steering pump
rotor slippers too long,
excessive rotor slipper-
to-slot clearance or
damaged or worn rotor
assembly. z
REPAIR or INSTALL a
new power steering
pump as necessary.
REFER to Section 211 -
02 .
z Power steering
pump clatter noise z
Damaged corners on
the outside diameter or
the power steering
rotor or distorted rotor
slipper ring. z
REPAIR or INSTALL a
new power steering
pump as necessary.
REFER to Section 211 -
02 .
Symptom Chart—
Suspension Noise/Vibration Condition
Possible Sources Action
z Squeak or grunt— noise
from the front suspension,
occurs more in cold
ambient temperatures.
More noticeable over
rough roads or when
turning z
Front stabilizer
bar insulators. z
Under these conditions,
the noise is acceptable.
CHECK TSBs. Klj . 36 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

acceleration from a slow
speed or stop
assembly
mispositioned. and the rear suspension
for damage or wear.
REPAIR as necessary.
z Incorrect or high
CV joint
operating angle. z
CHECK vehicle ride
height is within limits.
REPAIR as necessary.
z Damaged or
worn front
suspension
components. z
CHECK for a loose
stabilizer bar, damaged
or loose strut/strut
bushings or loose or
worn ball joints.
INSPECT the steering
linkage for wear or
damage. REPAIR or
INSTALL new
components as
necessary.
z Shimmy—most
noticeable on
coast/deceleration. Also
hard steering condition z
Excessive
positive caster. z
CHECK the caster
alignment angle.
CORRECT as
necessary. REFER to
Section 204 - 00 .
Symptom Chart—
Tire Noise/Vibration Condition
Possible Sources Action
z Tire noise— hum/moan
at constant speeds z
Abnormal wear
patterns. z
SPIN the tire and CHECK
for tire wear. INSTALL a
new tire as necessary.
INSPECT for
damaged/worn suspension
components. CARRY OUT
wheel alignment.
z Tire noise— noise tone
lowers as the vehicle
speed is lowered z
Out-of- balance
tire. z
BALANCE the tire and
road test. INSTALL a new
tire as necessary. REFER
to Section 204 - 04 .
z Tire noise — ticking
noise, changes with
speed z
Nail puncture or
stone in tire
tread. z
INSPECT the tire. REPAIR
as necessary.
z Wheel and tire—
vibration and noise
concern is directly
related to vehicle
speed and is not
affected by
acceleration, coasting
or decelerating z
Damaged or
worn tire. z
Go To Pinpoint Test J .
z Tire wobble or
shudder — occurs at
lower speeds z
Damaged wheel
bearings. z
SPIN the tire and CHECK
for abnormal wheel
bearing play or roughness.
ADJUST or INSTALL new
wheel bearings as
necessary. REFER to
Section 204 - 01 .
z Damaged wheel. zINSPECT the wheel for
damage. INSTALL a new
wheel as necessary.
REFER to Section 204 -Klj . 38 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Symptom Chart—
Transmission (Manual) and Transfer Case Noise/Vibration Condition
Possible Sources Action
z Clutch rattling noise—
occurs with clutch
engaged, noise
changes/disappears
with clutch pedal
depressed z
Flywheel bolts,
clutch housing bolts
or clutch pressure
plate bolts loose. z
TIGHTEN the bolts to
specifications. CHECK
the bolts for damage.
z Clutch squeaking
noise— noise is heard
when the clutch is
operated. Vehicle
moves slowly or
creeps when the clutch
is disengaged. Can
also be difficult to shift
into first and reverse
gear z
Pilot bearing seized
or damaged. z
INSTALL a new pilot
bearing. REFER to
Section 308 - 01 .
z Clutch squeaking
noise— occurs with
clutch pedal
depressed/released z
Worn clutch pedal
shaft or bushings. z
INSPECT the clutch
pedal for wear or
damage. REPAIR as
necessary. REFER to
Section 308 - 02 .
z Clutch whirring/rattle
noise— occurs when
clutch pedal is
depressed z
Worn, damaged or
misaligned clutch
release bearing. z
INSTALL a new clutch
release bearing.
REFER to Section 308 -
01 .
z Clutch grating/grinding
noise— occurs when
clutch pedal is
depressed z
Clutch pressure
plate fingers bent or
worn. z
INSPECT the clutch
pressure plate release
fingers. INSTALL a new
pressure plate as
necessary. REFER to
Section 308 - 01 .
z Contact surface of
clutch release
bearing worn or
damaged. z
INSTALL a new clutch
release bearing.
REFER to Section 308 -
01 .
z Clutch chatter— a
small amount of noise
when clutch pedal is
released at initial take-
off z
Clutch engagement. zAcceptable operating
condition.
z Clutch chatter/grabs—
in some cases a
shudder is felt. Occurs
with clutch pedal
depressed/released z
Damaged or worn
powertrain/driveline
mounts. z
INSPECT the
powertrain/drivetrain
mounts. INSTALL new
mounts as necessary.
REFER to Section 303 -
01A for 3.8L engines or
Section 303 - 01B for
4.6L (2V) engines.
z Binding or dragging
plunger of the clutch
master cylinder or
slave cylinder. z
CHECK the master and
slave cylinder
operation. INSPECT
the components for
damage or wear.
INSTALL a new master
or slave cylinder as
necessary. REFER to Klj . 40 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Section 308 - 02 .
z Grease or oil on the
clutch disc facing. z
CHECK the input shaft
seal and rear main oil
seal. REPAIR as
necessary. INSTALL a
new clutch disc.
REFER to Section 308 -
03A for T50D
transmissions or
Section 308 - 03B for
TR3650 transmissions.
z Clutch disc surface
glazed or damaged. z
INSPECT the clutch
disc surface for a
glazed, hardened or
damage condition.
CARRY OUT a disc
check. INSTALL a new
clutch disc as
necessary. REFER to
Section 308 - 01 .
z Damaged or worn
clutch pressure
plate. z
INSPECT the clutch
pressure plate for wear
or damage. INSTALL a
new clutch pressure
plate as necessary.
REFER to Section 308 -
01 .
z Flywheel surface
damaged or glazed. z
INSPECT the flywheel
for damage or wear.
CARRY OUT a
flywheel runout check.
INSTALL a new
flywheel as necessary.
REFER to Section 303 -
01A for 3.8L engines or
Section 303 - 01B for
4.6L (2V) engines.
z Clutch chatter noise—
noise when clutch
pedal is released at
initial take- off. Clutch is
hard to engage and
disengage z
Pilot bearing worn,
damaged or not
correctly aligned in
bore. z
INSPECT the clutch
pressure plate release
fingers for uneven
wear, clutch
components burnt or a
seized pilot bearing.
INSTALL a new pilot
bearing as necessary.
REFER to Section 308 -
01 .
z Clutch vibration zLoose flywheel
bolts.
z Damaged or loose
clutch pressure
plate.
z Excessive flywheel
runout. z
Go To Pinpoint Test L .
z Transmission
rattling/clattering
noise— noise at idle or
on light acceleration
from a stop. Gear
selection difficult z
Gearshift lever joint
worn or damaged. z
INSTALL a new
gearshift lever. REFER
to Section 308 - 03A for
T50D transmissions or
Section 308 - 03B for
TR3650 transmissions. Klj . 41 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Mismatched gear
sets. z
INSPECT the gear sets
for an uneven wear
pattern on the face of
the gear teeth. REPAIR
as necessary. REFER
to Section 308 - 03A for
T50D transmissions or
Section 308 - 03B for
TR3650 transmissions.
z Damaged or worn
transmission
bearing. z
INSPECT the
transmission bearings.
INSTALL new bearings
as necessary. REFER
to Section 308 - 03A for
T50D transmissions or
Section 308 - 03B for
TR3650 transmissions.
z Transmission
growling/humming—
noise occurs in the
forward gears. The
noise is more
prominent when the
gear is loaded. The
problem gear can be
located as the noise
occurs in a specific
gear position z
Gear is cracked,
chipped or rough. z
INSPECT the
transmission gears for
damage or wear.
INSTALL new gears as
necessary. REFER to
Section 308 - 03A for
T50D transmissions or
Section 308 - 03B for
TR3650 transmissions.
z Transmission
hissing— noise in
neutral or in forward
gears. As bearings
wear or break up, the
noise changes to a
thumping noise z
Damaged or worn
bearings. z
INSPECT the
transmission bearings.
INSTALL new bearings
as necessary. REFER
to Section 308 - 03A for
T50D transmissions or
Section 308 - 03B for
TR3650 transmissions.
z Transmission
knocking/thudding—
noise at low speeds in
forward gears z
Bearings with
damaged balls or
rollers or with pitted
and spalled races. z
INSPECT the
transmission bearings.
INSTALL new bearings
as necessary. REFER
to Section 308 - 03A for
T50D transmissions or
Section 308 - 03B for
TR3650 transmissions.
z Transmission
rumble/growl— noise at
higher speeds in
forward gears, more
pronounced in a
coast/deceleration
condition z
Incorrect driveline
angle. z
CHECK the driveline
angle. REPAIR as
necessary. REFER to
Section 205 - 00 .
z Driveshaft out of
balance or
damaged. z
CHECK the driveshaft
for damage, missing
balance weights or
undercoating. Using the
vibration analyzer (VA),
CHECK the driveshaft
balance. CARRY OUT
a driveline vibration
test. For additional Klj . 43 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

information, REFER to
Section 205
- 00 .
REPAIR as necessary.
z Transmission
rumble/growl— noise at
all speeds in forward
gears, more
pronounced in a heavy
acceleration condition z
Damaged or worn
transmission
bearing or gears
(high mileage
vehicles). z
CHECK transmission
fluid for excessive
metal particles.
REPAIR as necessary.
REFER to Section 308 -
03A for T50D
transmissions or
Section 308 - 03B for
TR3650 transmissions.
z Transfer case whine—
noise at all ranges z
Incorrect fluid level
or fluid quality. z
CHECK that the
transfer case is filled to
the correct level and
with the specified fluid.
REFER to Section 308 -
03A for T50D
transmissions or
Section 308 - 03B for
TR3650 transmissions.
z Worn oil pump. zDISASSEMBLE the
transfer case. CHECK
the oil pump for wear or
damage. REPAIR as
necessary.
z Under- inflated or
oversized tires. z
CONFIRM that the tires
and wheels are correct
for the vehicle. CHECK
that the tire inflation
pressures are correct.
z Transfer case
growl/rumble— noise at
all ranges (A small
amount of planetary
noise can be heard
when the transfer case
is operated in low
range.) z
Damaged or worn
bearings or
planetary gear. z
DISASSEMBLE the
transfer case. CHECK
the bearings or
planetary gear for wear
or damage. REPAIR as
necessary.
z Transfer case
scraping/grating—
noise at all ranges z
Excessively
stretched drive
chain hitting the
case. z
DISASSEMBLE the
transfer case. CHECK
the drive chain for wear
or damage. REPAIR as
necessary.
z Transfer case
howl/hum— noise at all
ranges or high range
only z
Worn or damaged
sun (input) gear,
clutch pack
(intermediate) gear
or output shaft gear. z
DISASSEMBLE the
transfer case. CHECK
the gears for wear or
damage. REPAIR as
necessary.
z Transfer case
howl/hum— noise at
low range only z
Worn or damaged
intermediate gear
and sliding gears
(clutch pack). z
DISASSEMBLE the
transfer case. CHECK
the gears for wear or
damage. REPAIR as
necessary.
z Transfer case
vibration— vibration felt
with vehicle in 4WD z
Transfer case
mounting.
z Driveshaft out of
balance.
z Excessive pinion z
Go To Pinpoint Test M . Klj . 44 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

flange runout.
Symptom Chart—
Transmission (Automatic) Noise/Vibration Condition
Possible Sources Action
z Rattle— occurs
at idle or at
light
acceleration
from a stop z
Damaged engine or
transmission mounts. z
CHECK the
powertrain/drivetrain mounts
for damage. REPAIR or
INSTALL new mounts as
necessary.
z A loose front exhaust
pipe heat shield. z
REPAIR or INSTALL a new
heat shield as necessary.
z Loose inspection
plate or dust cover
plate. z
CHECK for loose bolts.
TIGHTEN to specifications.
REFER to Section 307 - 01 .
z Loose flex plate to
converter nuts. z
CHECK for loose nuts.
TIGHTEN to specifications.
REFER to Section 307 - 01 .
z Whine— pitch
increases with
vehicle speed.
Starts in first
and second
gear,
decreases or
goes away at
higher gears z
Damaged or worn low
one- way clutch.
z Damaged or worn
intermediate one- way
clutch.
z Friction elements.
z Damaged or worn
planetary or sun gear. z
INSPECT the transmission
for wear or damage. REPAIR
or INSTALL new components
as necessary. REFER to
Section 307 - 01 .
z Whine— the
pitch changes
with engine
speed z
A worn or damaged
accessory drive
component. z
CARRY OUT the Engine
Accessory Test. REPAIR or
INSTALL new components as
necessary.
z Incorrect fluid level. zCHECK that the transmission
is filled to the correct level.
ADD fluid as necessary.
REFER to Section 307 - 01 .
z Partially blocked filter. zINSPECT the filter. CLEAN or
INSTALL a new filter as
necessary. REFER to Section 307 - 01 .
z Worn or damaged
torque converter. z
CARRY OUT the torque
converter service and
replacement check. REFER
to Section 307 - 01 .
z Worn or damaged
front pump. z
INSPECT the front pump.
INSTALL a new front pump
as necessary. REFER to
Section 307 - 01 .
z Whine— pitch
changes with
vehicle speed z
Speedometer cable
or gears. z
REPAIR or INSTALL new
cables or gears as necessary.
z Whine/moan
type noise—
pitch increases
or changes
with vehicle
speed z
Damaged engine or
transmission mount. z
CHECK the
powertrain/drivetrain mounts
for damage. CARRY OUT
Powertrain/Drivetrain Mount Neutralizing in this section.
z U-joints worn or zINSPECT the U- joints for Klj . 45 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

damaged.
wear or damage. INSTALL
new U-joints as necessary.
REFER to Section 205 - 01 .
z Damaged or worn
differential ring and
pinion. z
INSPECT the differential ring
and pinion for damage.
CARRY OUT the Checking
Tooth Contact Pattern and
Condition of the Ring and
Pinion component test in this
section. REPAIR or INSTALL
a new differential ring and
pinion as necessary. REFER
to Section 205 - 02A for Ford
7.5 rear axles or Section 205 -
02B for Ford 8.8 integral
axles.
z Planetary gears
nicked or chipped. z
CHECK the planetary gears
for damage. INSTALL new
components as necessary.
REFER to Section 307 - 01 .
z Whistle— noise
is high pitched,
constant.
Changes in
pitch with
throttle position z
Hydraulic pressure in
the main control. z
INSPECT the main control.
REPAIR or INSTALL new
components as necessary.
REFER to Section 307 - 01 .
z Incorrect band/clutch
apply pressure. z
CARRY OUT the line
pressure tests. REPAIR or
INSTALL components as
necessary. REFER to Section 307 - 01 .
z Worn or damaged
torque converter. z
CARRY OUT the torque
converter service and
replacement check. REFER
to Section 307 - 01 .
z Clunk— occurs
when shifting
from PARK to
a drive or
reverse
position z
Damaged powertrain
mounts. z
INSPECT the powertrain
mounts for damage. INSTALL
new mounts as necessary.
z Damaged or worn
pinion bearings. z
CHECK for abnormal bearing
play or roughness. INSTALL
new bearings as necessary.
REFER to Section 205 - 02A
for Ford 7.5 rear axles or
Section 205
- 02B for Ford 8.8
integral axles.
z Worn or galled
driveshaft slip yoke
splines. z
CLEAN and INSPECT the
splines of the yoke. INSTALL
a new slip yoke as necessary.
REFER to Section 205 - 01 .
z Worn friction
elements or
excessive clutch pack
end plate play. z
INSPECT the transmission
for wear. CHECK that all end
play and clearances are
within specification. REPAIR
or INSTALL new components
as necessary. REFER to
Section 307 - 01 . Klj . 46 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...