2003 FORD MUSTANG air condition

NOTE:
A serpentine drive belt decreases the usefulness of this test. In these cases, use a
vibration analyzer, such as the VA, to pinpoint accessory vibrations. An electronic listening
device, such as an EngineEAR, will also help to identify noises from specific accessories.
Remove the accessory drive belts.
z Increase the engine rpm to where the concern occurs.
z If the vibration/noise is duplicated when carrying out this test, the belts and accessories are not
sources.
z If the vibration/noise was not duplicated when carrying out this test, install each accessory belt,
one at a time, to locate the source.
Vehicle Cold Soak Procedure
To carry out this procedure, proceed as follows:
zTest preparations include matching customer conditions (if known). If not known, document the
test conditions: gear selection and engine rpm. Monitor the vibration/noise duration with a watch
for up to three minutes.
z Park the vehicle where testing will occur. The vehicle must remain at or below the concern
temperature (if known) for 6- 8 hours.
z Before starting the engine, conduct a visual inspection under the hood.
z Turn the key on, but do not start the engine. Listen for the fuel pump, anti- lock brake system
(ABS) and air suspension system noises.
z Start the engine.
z CAUTION: Never probe moving parts.
Isolate the vibration/noise by carefully listening. Move around the vehicle while listening to find
the general location of the vibration/noise. Then, search for a more precise location by using a
stethoscope or EngineEAR.
z GO to Symptom Chart — Idle Noise/Vibration to assist with the diagnosis.
6: Check OASIS/TSBs/Repair History
After verifying the customer concern, check for OASIS reports, TSBs and the vehicle repair history for
related concerns. If information relating to a diagnosis/repair is found, carry out the procedure(s)
specified in that information.
If no information is available from these sources, carry out the vehicle preliminary inspection to
eliminate any obvious faults.
7: Diagnostic Procedure
Qualifying the concern by the particular sensation present can help narrow down the concern. Always
use the "symptom" to "system" to "component" to "cause" diagnosis technique. This diagnostic method
divides the problem into related areas to correct the customer concern.
zVerify the "symptom".
z Determine which "system(s)" can cause the "symptom".
„If a vibration concern is vehicle speed related, the tire and wheel rpm/frequency or
driveshaft frequency should be calculated.
„ If a vibration concern is engine speed related, the engine, engine accessory or engine
firing frequencies should be calculated. Klj . 9 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

„
Loudness proportional to vehicle speed. Low- frequency noise at high
speeds, noise and loudness increase with speed. GO to Symptom Chart —
Driveline Noise/Vibration .
„ A low- pitched noise (drumming). GO to Symptom Chart — Engine
Noise/Vibration .
„ Vibration occurs at a particular speed (mph) regardless of acceleration or
deceleration. GO to Symptom Chart — Tire Noise/Vibration .
„ Noise varies with wind/vehicle speed and direction. GO to Symptom Chart — Air Leak and Wind Noise .
„ Related to engine speed.
„Noise varies with engine rpm. GO to Symptom Chart — Engine
Noise/Vibration .
„ Vibration occurs at a particular speed (mph) regardless of engine speed
(rpm).
2. Acceleration
„Wide open throttle (WOT)
„Engine induced contact between components. Inspect and repair as
necessary.
„ Noise is continuous throughout WOT. Exhaust system or engine ground
out. GO to Symptom Chart — Engine Noise/Vibration .
„ Light/moderate acceleration
„Tip- in moan. Engine/exhaust noise. GO to Symptom Chart — Engine
Noise/Vibration .
„ Knock-type noise. GO to Symptom Chart — Engine Noise/Vibration .
„ Driveline shudder. GO to Symptom Chart — Driveline Noise/Vibration .
„ Engine vibration. GO to Symptom Chart — Engine Noise/Vibration .
3. Turning noise. GO to Symptom Chart — Steering Noise/Vibration .
4. Braking
„Clicking sound is signaling ABS is active. Acceptable ABS sound.
„ A continuous grinding/squeal. GO to Symptom Chart — Brake Noise/Vibration .
„ Brake vibration/shudder. GO to Symptom Chart — Brake Noise/Vibration .
5. Clutching
„A noise occurring during clutch operation. GO to Symptom Chart — Transmission
(Manual) and Transfer Case Noise/Vibration .
„ Vibration. GO to Symptom Chart — Transmission (Manual) and Transfer Case
Noise/Vibration .
6. Shifting
„Noise or vibration condition related to the transmission (automatic). GO to
Symptom Chart — Transmission (Automatic) Noise/Vibration .
„ Noise or vibration related to the transmission (manual). GO to Symptom Chart —
Transmission (Manual) and Transfer Case Noise/Vibration .
7. Engaged in four- wheel drive. GO to Symptom Chart — Transmission (Manual) and
Transfer Case Noise/Vibration .
8. Cruising speeds
„Accelerator pedal vibration. GO to Symptom Chart — Engine Noise/Vibration .
„ Driveline vibration. GO to Symptom Chart — Driveline Noise/Vibration .
„ A shimmy or shake. GO to Symptom Chart — Tire Noise/Vibration .
9. Driving at low/medium speeds Klj . 11 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

„
A wobble or shudder. GO to Symptom Chart — Tire Noise/Vibration .
2. Depends more on where the vehicle is operated 1. Bump/pothole, rough road or smooth road. GO to Symptom Chart — Suspension
Noise/Vibration .
„ Noise is random or intermittent occurring from road irregularities. GO to Symptom Chart — Squeak and Rattle .
„ Noise or vibration changes from one road surface to another. Normal sound
changes.
„ Noise or vibration associated with a hard/firm ride. GO to Symptom Chart —
Suspension Noise/Vibration .
Symptom Charts Symptom Chart — Air Leak and Wind Noise Condition
Possible Sources Action
z Air leak around
door perimeter z
Loose fit seal. zPINCH the seal carrier to
improve retention on the
seal flange.
z Seal installed
incorrectly. z
REINSTALL the seal.
z Door misaligned. zREALIGN the door.
CHECK door gaps and fit
in the door opening and
ADJUST as necessary.
z Scuff plate installed
incorrectly. z
REINSTALL the scuff
plate.
z Seal or seal push pins
damaged. z
INSTALL a new seal.
z Air leak around
glass run z
Door glass misaligned. zADJUST the door glass.
z Glass run installed
incorrectly. z
ADJUST the glass run.
INSERT foam in the glass
run carrier.
z Leak path behind glass
run. z
INSTALL foam rope
behind the glass run.
z Glass run channel
spread wide. z
PINCH the glass run
channel to reduce the size
of the opening.
z Blow- out clip bent or
contacting door glass. z
ADJUST the blow- out clip
or INSTALL a new glass
run/blow- out clip molding
assembly.
z Glass run damaged. zINSTALL a new glass run.
z Air leak at inner
belt line z
Belt line seal installed
incorrectly on flange. z
ADJUST the seal. (Do not
bend the flange.)
z Belt line seal integrated
with door trim installed
incorrectly (no glass
contact). z
REINSTALL the door trim. Klj . 12 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Body panel misaligned
(exposed edge). z
REALIGN the appropriate
body panel.
z Hood misaligned (front
margin). z
CHECK hood gaps and fit.
ADJUST the hood as
necessary.
z Front grille edge noise. zAPPLY foam in the hollow
areas behind the louvers.
z Wind noise
created by grille
opening panel z
Grille relationship to
leading edge on hood. z
ADJUST the grille
opening panel forward to
eliminate wind noise.
z Sharp edges due to
material imperfections. z
REMOVE the sharp
edges (no damage to
visible surface).
z Wind noise from
air extractor z
Air extractor housing
seated incorrectly. z
REINSTALL the air
extractor housing.
z Air extractor housing or
flaps damaged. z
INSTALL a new air
extractor.
z Air leak at top of
A-pillar —
vehicles with a
convertible top z
Seal at windshield
header installed
incorrectly. z
REINSTALL the seal.
z Seal pinched. zFILL the seal with foam to
reshape it.
z Gap between side rail
and header seal at A-
pillar. z
ADJUST the J-hook/vinyl
top.
z Air leak at rear
quarter glass
(division bar) —
vehicles with a
convertible top z
No contact between
front side glass and
quarter glass division
bar. z
ADJUST the front side
glass regulator and the
rear quarter glass
regulator.
z Air leak or wind
noise from top of
side glass —
vehicles with a
convertible top z
Gap between side rail
and vinyl top. z
ADD additional foam tape
to seal between the side
rail and the vinyl top.
z Seal at windshield
header installed
incorrectly. z
REINSTALL the seal.
z Seal damaged
between side rail and
vinyl top. z
INSTALL a new seal.
z Vinyl top damaged. zINSPECT the vinyl top.
INSTALL a new vinyl top
as necessary.
z Air leak or wind
noise at
windshield
header —
vehicles with a
convertible top z
Vinyl top not flush with
header. z
ADJUST the J-hook to
lower the top to achieve a
flush condition.
z Seal at windshield
header installed
incorrectly. z
REINSTALL the seal.
z Header seal not flush zREINSTALL the seal. Klj . 15 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

occurs on first
(morning) brake
application
pads.
Caused by humidity and
low disc brake pad
temperature.
z Squealing noise— a
continuous squeal z
Disc brake pads
or linings worn
below minimum
thickness. z
INSTALL new disc brake
pads. REFER to Section 206 - 03 for front disc brake
pads or Section 206 - 04 for
rear disc brake pads.
z Squealing noise— an
intermittent squeal
brought on by cold,
heat, water, mud or
snow z
Disc brake pad. zAcceptable condition.
z Groaning noise—
occurs at low speeds
with brake lightly
applied (creeping) z
Disc brake
pads. z
Acceptable condition.
z Grinding noise—
continuous z
Disc brake pads
or linings worn
below minimum
thickness. z
INSPECT the disc brake
pads, brake discs and
attaching hardware for
damage. REPAIR or
INSTALL new components
as necessary. REFER to
Section 206 - 03 for front
disc brakes and Section 206 - 04 for rear disc brakes.
z Moaning noise zBrake linings
contaminated
with grease or
oil. z
INSPECT the brake pads
and shoes for
contamination. REPAIR or
INSTALL new components
as necessary. REFER to
Section 206 - 03 for front
disc brakes or Section 206 -
04 for rear disc brakes.
z Brake
vibration/shudder—
occurs when brakes
are applied z
Uneven disc or
drum wear.
z Uneven disc
brake pad or
lining transfer.
z Suspension
components. z
Go To Pinpoint Test A .
z Brake
vibration/shudder—
occurs when the brake
pedal is released z
Brake drag. zINSPECT the disc brake
pads or linings for
premature wear. REPAIR
or INSTALL a new caliper
or wheel cylinder as
necessary. REFER to
Section 206 - 03 for front
disc brakes and Section 206 - 04 for rear disc brakes.
Symptom Chart—
Driveline Noise/Vibration Condition
Possible Sources Action
z Axle howling or
whine— front or rear
axle z
Axle lubricant
low. z
CHECK the lubricant level.
FILL the axle to
specification.
z Axle housing zINSPECT the axle housing Klj . 17 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

components as necessary.
z Broken
powertrain
mounts. z
INSPECT the powertrain
mounts. INSTALL new
mounts as necessary.
REFER to Section 303 - 01A
for 3.8L engines or
Section 303 - 01B for 4.6L (2V)
engines.
z Idle speed too
high. z
CHECK for the correct idle
speed.
z Driveline clunk—
occurs as the vehicle
starts to move
forward following a
stop z
Worn or galled
driveshaft slip-
yoke splines. z
CLEAN and INSPECT the
splines of the yoke for a
worn or galled condition.
INSTALL a new yoke as
necessary. REFER to
Section 205 - 01 .
z Worn or galled
driveshaft and
coupling shaft
splines. z
CLEAN and INSPECT the
splines of the driveshaft and
coupling shaft for a worn or
galled condition. INSTALL a
new driveshaft assembly as
necessary. REFER to
Section 205 - 01 .
z Loose rear leaf
spring U- bolts. z
CHECK the U- bolts for
loose nuts. TIGHTEN to
specification. REFER to
Section 204 - 02 .
z Driveline clunk (FWD
vehicles)—occurs
during acceleration or
from cruise to
coast/deceleration z
Damaged or
worn inboard
constant velocity
(CV) joint. z
INSPECT the inboard CV
joint and boot. REPAIR or
INSTALL a new CV joint as
necessary.
z Driveline clunk (4WD
vehicles)—occurs
during shift- on-the- fly
engagement z
Clutch relay.
z Shift motor.
z Transfer case.
z GEM. z
CHECK the 4WD
engagement system.
REPAIR or INSTALL new
components as necessary.
z Clicking, popping or
grinding— occurs
while vehicle is
turning z
Inadequate or
contaminated
lubrication in the
(CV) joints. z
CHECK the CV boots and
joints for wear or damage.
REPAIR or INSTALL new
components as necessary.
z Another
component
contacting the
halfshaft. z
CHECK the halfshafts and
the area around the
halfshafts. REPAIR as
necessary.
z Brake
components. z
INSPECT the front brakes
for wear or damage.
REPAIR as necessary.
REFER to Section 206 - 03 .
z Steering
components. z
INSPECT the drag link,
inner and outer tie- rods or
idler arm for wear or
damage. REPAIR as
necessary. REFER to
Section 211 - 02 .
z Suspension
components. z
INSPECT the upper and
lower ball joints for wear or
damage. REPAIR as
necessary. REFER to Klj . 19 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

from a dead stop
zLoose rear
spring U- bolts. z
INSPECT the rear
suspension. TIGHTEN the
U-bolt nuts to specification.
REFER to Section 204 - 02 .
z Howl— can occur at
various speeds and
driving conditions.
Affected by
acceleration and
deceleration z
Incorrect ring
and pinion
contact,
incorrect
bearing preload
or gear damage. z
CHECK the ring and pinion
and bearings for damage.
INSPECT the ring and
pinion wear pattern. REFER
to Checking Tooth Contact
Pattern and Condition of the
Ring and Pinion component
test in this section. ADJUST
or INSTALL new
components as necessary.
REFER to Section 205 - 02A
for Ford 7.5 rear axles or
Section 205
- 02B for Ford
8.8 integral axles.
z Chuckle— heard at
coast/deceleration.
Also described as a
knock z
Incorrect ring
and pinion
contact or by
damaged teeth
on the coast
side of the ring
and pinion. z
CHECK the ring and pinion
for damage. INSPECT the
ring and pinion wear pattern.
REFER to Checking Tooth
Contact Pattern and
Condition of the Ring and
Pinion component test in
this section. ADJUST or
INSTALL new components
as necessary. REFER to
Section 205 - 02A for Ford
7.5 rear axles or Section 205 - 02B for Ford 8.8
integral axles.
z Knock— noise occurs
at various speeds.
Not affected by
acceleration or
deceleration z
Gear tooth
damage to the
drive side of the
ring and pinion. z
CHECK the differential case
and ring and pinion for
damage. INSTALL new
components as necessary.
REFER to Section 205 - 02A
for Ford 7.5 rear axles or
Section 205
- 02B for Ford
8.8 integral axles.
z Excessive axle
shaft end play.
(Vehicles with
integral axles). z
CHECK the axle end play
using a dial indicator.
INSTALL a new axle shaft
or side gears as necessary.
REFER to Section 205 - 02A
for Ford 7.5 rear axles or
Section 205
- 02B for Ford
8.8 integral axles.
z Scraping noise— a
continuous low
pitched noise starting
at low speeds z
Worn or
damaged pinion
bearings. z
CHECK the pinion bearings.
INSTALL new pinion
bearings as necessary.
REFER to Section 205 - 02A
for Ford 7.5 rear axles or
Section 205
- 02B for Ford
8.8 integral axles.
z Driveline shudder—
occurs during
acceleration from a
slow speed or stop z
Rear drive axle
assembly
mispositioned. z
CHECK the axle mounts
and the rear suspension for
damage or wear. REPAIR
as necessary. Klj . 21 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Loose rear
spring U- bolts. z
INSPECT the U- bolts.
TIGHTEN the U- bolt nuts to
specification. REFER to
Section 204 - 02 .
z Incorrect or high
CV joint
operating angle. z
CHECK vehicle ride height
is within limits. REPAIR as
necessary. REFER to
Section 206 - 00 .
z Damaged or
worn front
suspension
components. z
CHECK for a loose stabilizer
bar, damaged or loose
strut/strut bushings or loose
or worn ball joints. INSPECT
the steering linkage for wear
or damage. REPAIR or
INSTALL new components
as necessary.
z Driveline angles
out of
specification. z
CHECK for correct driveline
angles. REPAIR as
necessary. REFER to
Section 205 - 00 .
z U-joints binding
or seized. z
ROTATE the driveshaft and
CHECK for rough operation
or seized U- joints. INSTALL
new U- joints as necessary.
REFER to Section 205 - 01 .
z Binding,
damaged or
galled splines
on the driveshaft
slip- yoke z
CLEAN and INSPECT the
splines of the slip- yoke,
driveshaft and coupling
shaft for a worn, damaged
or galled condition.
INSTALL a new slip- yoke or
driveshaft assembly as
necessary. REPAIR as
necessary. REFER to
Section 205 - 01 .
z Driveline vibration—
occurs at cruising
speeds z
U-joints are
worn. z
CHECK for wear or incorrect
seating. INSTALL new U-
joints as necessary. REFER
to Section 205 - 01 .
z Worn or
damaged
driveshaft center
bearing support. z
CHECK the insulator for
damage or wear. ROTATE
the driveshaft and CHECK
for rough operation.
INSTALL a new center
bearing support as
necessary. REFER to
Section 205 - 01 .
z Loose axle
pinion flange
bolts. z
INSPECT the axle pinion
flange. TIGHTEN the pinion
flange bolts to specification.
REFER to Section 205 - 01 .
z Excessive axle
pinion flange
runout. z
CARRY OUT a Runout
Check. REPAIR as
necessary. REFER to
Section 205 - 01 .
z Driveshaft is
out-of- balance. z
CHECK the driveshaft for
damage, missing balance
weights or undercoating.
CHECK driveshaft balance. Klj . 22 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...