2003 FORD MUSTANG oil level

GENERAL PROCEDURES
Hydro-
Boost Bleeding
1. NOTE: The Hydro- Boost power brake booster (2B560) is generally self- bleeding, and the
following procedure will normally bleed the air from the power brake booster. Normal operation
of the vehicle will further remove any additional trapped air.
Fill the power steering oil reservoir (3A697) with MERCON® Multi- Purpose ATF XT-2-QDX or
MERCON® equivalent.
2. Remove the powertrain control module (PCM) fuse to prevent the engine from starting.
3. Crank the engine for several seconds.
4. Check the fluid level in the power steering oil reservoir and add if necessary. Install the powertrain control module (PCM) fuse.
5. Start the engine.
6. With the engine running, turn the steering wheel (3600) from stop- to-stop twice. Turn the engine
off.
7. Depress the brake pedal (2455) several times to discharge the accumulator.
8. Repeat Steps 5 and 6.
9. If foaming occurs, stop the engine and allow the foam to dissipate.
10. Repeat Steps 5 and 6 as required, until all the air is removed from the system (when the foaming stops).
SECTION 206-
07: Power Brake Actuation 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

GENERAL PROCEDURES
System Flushing —
CII Power Steering Pump
WARNING: Do not mix oil types. Any mixture or any unapproved oil can lead to seal
deterioration and leaks. A leak can ultimately cause loss of fluid, which can result in a loss of
power steering assist.
1. Remove the fuel pump fuse from the battery junction box.
2. Disconnect the power steering return hose. Plug the reservoir.
3. Attach an extension hose between the power steering return hose and an empty container.
4. Raise the front wheels off the floor. For additional information, refer to Section 100 - 02 .
5. Check the fluid level. If necessary, fill the reservoir to the correct level. zUse Motorcraft MERCON® Multi-Purpose ATF XT -2-QDX or MERCON® equivalent.
6. CAUTION: Do not crank the engine for more than 15 seconds at a time. Allow the
starter to cool for 1 minute before cranking again. Premature starter failure can occur.
CAUTION: Do not hold the steering wheel against the stops for more than three to
five seconds at a time. Damage to the power steering pump will occur.
Turn the steering wheel from stop- to-stop while cranking the engine until the fluid exiting the
power steering return hose is clear of all contamination and foreign material.
zAdd Motorcraft MERCON® Multi-Purpose ATF XT -2-QDX or MERCON® equivalent as
needed.
7. Lower the vehicle.
8. Disconnect the extension hose from the power steering return hose. Remove the plug. Attach the power steering return hose to the reservoir.
SECTION 211-
00: Steering System — General Information 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

GENERAL PROCEDURES
System Flushing —
CIII Power Steering Pump
WARNING: Do not mix oil types. Any mixture or any unapproved oil can lead to seal
deterioration and leaks. A leak can ultimately cause loss of fluid, which can result in a loss of
power steering assist.
1. Remove the fuel pump fuse from the battery junction box.
2. Disconnect the power steering return hose. Plug the reservoir.
3. Attach an extension hose between the power steering return hose and an empty container.
4. Raise the front wheels off the floor. For additional information, refer to Section 100 - 02 .
5. Check the fluid level. If necessary, fill the reservoir to the correct level. zUse Motorcraft MERCON® Multi-Purpose ATF XT -2-QDX or MERCON® equivalent.
6. CAUTION: Do not crank the engine for more than 15 seconds at a time. Allow the
starter to cool for 1 minute before cranking again. Premature starter failure can occur.
CAUTION: Do not hold the steering wheel against the stops for more than three to
five seconds at a time. Damage to the power steering pump could occur.
Turn the steering wheel from stop- to-stop while cranking the engine until the fluid exiting the
power steering return hose is clear of all contamination and foreign material.
zAdd Motorcraft MERCON® Multi-Purpose ATF XT -2-QDX or MERCON® equivalent as
needed.
7. Lower the vehicle.
8. Disconnect the extension hose from the power steering return hose. Remove the plug. Attach the power steering return hose to the reservoir.
SECTION 211-
00: Steering System — General Information 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

GENERAL PROCEDURES
Fill
1. WARNING: Do not mix oil types, any mixture or any unapproved oil can lead to seal
deterioration and leaks. A leak can ultimately cause loss of fluid, which can result in a
loss of power steering assist.
Check the fluid level. If necessary, fill the reservoir to the correct level.
zUse Motorcraft MERCON® Multi-Purpose ATF XT -2-QDX or MERCON® equivalent.
2. Remove the fuel pump fuse from the battery junction box.
3. Raise the front wheels off the floor. For additional information, refer to Section 100 - 02 .
4. CAUTION: Do not crank the engine for more than 15 seconds at a time. Allow the
starter to cool for 1 minute before cranking again. Premature starter failure can occur.
CAUTION: Do not hold the steering wheel against the stops for more than three to
five seconds at a time. Damage to the power steering pump will occur.
Turn the steering wheel from stop- to-stop while cranking the engine.
5. Lower the vehicle.
6. CAUTION: Do not overfill the reservoir.
Check the fluid level. If necessary, fill the reservoir to the correct level. zUse Motorcraft MERCON® Multi-Purpose ATF XT -2-QDX or MERCON® equivalent.
7. Install the fuel pump fuse.
SECTION 211-
00: Steering System — General Information 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
intake manifold gaskets
z cylinder head gaskets
z oil bypass filter
z oil filter adapter
z engine front cover
z oil filter adapter and filter body
z oil level indicator tube connection
z oil pressure sensor
Leakage Points— Under Engine—With Vehicle on Hoist
z oil pan gaskets (6710)
z oil pan sealer
z oil pan rear seal (6723)
z engine front cover gasket
z crankshaft front seal (6700)
z crankshaft rear oil seal (6701)
z crankshaft main bearing cap side bolts
z oil filter adapter and filter body
z oil cooler, if equipped
Leakage Points— With Transmission and Flywheel Removed
z crankshaft rear oil seal
z rear main bearing cap parting line
z rear main bearing cap and seals
z flywheel mounting bolt holes (with flywheel [6375] installed)
z camshaft rear bearing covers (6266) or pipe plugs at the end of oil passages
Oil leaks at crimped seams in sheet metal parts and cracks in cast or stamped parts can be detected
when using the dye method.
Compression Test— Compression Gauge Check
1. Make sure the oil in the crankcase is of the correct viscosity and at the correct level and that the battery (10655) is correctly charged. Operate the vehicle until the engine is at normal operating
temperature. Turn the ignition switch to the OFF position, then remove all the spark plugs
(12405).
2. Set the throttle plates in the wide- open position.
3. Install a compression gauge such as the Compression Tester in the No. 1 cylinder.
4. Install an auxiliary starter switch in the starting circuit. With the ignition switch in the OFF position, and using the auxiliary starter switch, crank the engine a minimum of five compression
strokes and record the highest reading. Note the approximate number of compression strokes Klj . 7 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

1. If compression improves considerably, piston rings are faulty.
2. If compression does not improve, valves are sticking or seating incorrectly.
3. If two adjacent cylinders indicate low compression pressures and squirting oil on each piston
does not increase compression, the head gasket may be leaking between cylinders. Engine oil
or coolant in cylinders could result from this condition.
Use the Compression Pressure Limit Chart when checking cylinder compression so that the
lowest reading is within 75 percent of the highest reading.
Cylinder Leakage Detection
When a cylinder produces a low reading, use of the Engine Cylinder Leak Detection/Air Pressurization
Kit will be helpful in pinpointing the exact cause.
The leakage detector is inserted in the spark plug hole, the piston is brought up to dead center on the
compression stroke, and compressed air is admitted.
Once the combustion chamber is pressurized, a special gauge included in the kit will read the
percentage of leakage. Leakage exceeding 20 percent is excessive.
While the air pressure is retained in the cylinder, listen for the hiss of escaping air. A leak at the intake
valve (6507) will be heard in the throttle body (9E926). A leak at the exhaust valve (6505) can be
heard at the tail pipe. Leakage past the piston rings will be audible at the positive crankcase ventilation
(PCV) connection. If air is passing through a blown head gasket to an adjacent cylinder, the noise will
be evident at the spark plug hole of the cylinder into which the air is leaking. Cracks in the cylinder
block or gasket leakage into the cooling system may be detected by a stream of bubbles in the radiator
(8005).
Oil Consumption Test
The following diagnostic procedure is used to determine the source of excessive internal oil
consumption. 1. NOTE: Oil use is normally greater during the first 16,100 km (10,000 miles) of service. As
mileage increases, oil use generally decreases. Vehicles in normal service should get at least
1,450 km per liter (900 miles per quart) after 16,000 km (10,000 miles) of service. High speed
driving, towing, high ambient temperature and other factors may result in greater oil use.
Define excessive oil consumption, such as the number of miles driven per liter (quart) of oil
used. Also determine customer's driving habits, such as sustained high speed operation,
towing, extended idle and other considerations.
2. Verify that the engine has no external oil leak as described under Engine Oil Leaks in the Diagnosis and Testing portion of this section.
3. Verify that the engine has the correct oil level dipstick (6750).
4. Verify that the engine is not being run in an overfilled condition. Check the oil level at least five minutes after a hot shutdown with the vehicle parked on a level surface. In no case should the
level be above MAX or the letter F in FULL. If significantly overfilled, carry out Steps 6a through
6d.
5. Verify the spark plugs are not oil saturated. If the spark plugs are oil saturated and compression is good it can be assumed the valve seals or valve guides are at fault. Klj . 9 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

6. Carry out an oil consumption test:
a. Drain the engine oil, remove the oil bypass filter (6714) and refill with one liter (quart) less than
the recommended amount.
b. Run the engine for three minutes (10 minutes if cold), and allow the oil to drain back for at least five minutes with the vehicle on a level surface.
c. Remove oil level dipstick and wipe clean. (Do not wipe with anything contaminated with silicone compounds.) Reinstall the oil level dipstick, being sure to seat it firmly in the oil level indicator
tube (6754). Remove the oil level dipstick and draw a mark on the back (unmarked) surface at
the indicated oil level. This level should be about the same as the MIN or ADD mark on the face
of the oil level dipstick.
d. Add one liter (quart) of oil. Restart the engine and allow to idle for at least two minutes. Shut off the engine and allow the oil to drain back for at least five minutes. Mark the oil level dipstick,
using the procedure above.
e. Record the vehicle mileage. f. Instruct the customer to drive the vehicle as usual and perform the following:
„Check the oil level regularly at intervals of 160 to 240 km (100- 150 miles).
„ Return to the service point when the oil level drops below the lower (MIN or ADD) mark
on the oil level dipstick.
„ Add only full liters (quarts) of the same oil in an emergency. Note the mileage at which
the oil is added.
g. Check the oil level under the same conditions and at the same location as in Steps 6c and 6d.
„Measure the distance from the oil level to the UPPER mark on the oil level dipstick and
record.
„ Measure the distance between the two scribe marks and record.
„ Divide the first measurement by the second.
„ Divide the distance driven during the oil test by the result. This quantity is the
approximate oil consumption rate in kilometers per liter or in miles per quart.
h. If the oil consumption rate is unacceptable, go to Step 7.
7. Check the positive crankcase ventilation (PCV) system. Make sure the system is not plugged.
8. Check for plugged oil drain- back holes in the cylinder heads and cylinder block.
9. If the condition still exists after performing the above steps, go to Step 10.
10. Perform a cylinder compression test or perform a cylinder leak detection test with Engine Cylinder Leak Detection/Air Pressurization Kit. This can help determine the source of oil
consumption such as valves, piston rings or other areas.
11. NOTE: After determining if new parts should be installed, make sure correct parts are used.
Check valve guides for excessive guide clearance. Install new all valve stem seals (6571) after
verifying valve guide clearance.
12. Worn or damaged internal engine components can cause excessive oil consumption. Small deposits of oil on the tips of spark plugs can be a clue to internal oil consumption. If internal oil
consumption still persists, proceed as follows:
a. Remove the engine from the vehicle and place it on an engine work stand. Remove the intake manifolds (9424), cylinder heads, oil pan (6675) and oil pump (6600).
b. Check piston ring clearance, ring gap and ring orientation. Repair as necessary.
c. Check for excessive bearing clearance. Repair as necessary.
13. Repeat the oil consumption test (Step 6) to confirm the oil consumption concern has been resolved. Klj . 10 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Engines need oil to lubricate the following internal components:
zcylinder block cylinder walls
z pistons and piston, pin and rings (6102)
z intake and exhaust valve stems
z intake and exhaust valve guides
z all internal engine components
When the pistons move downward, a thin film of oil is left on the cylinder walls. As the vehicle is
operated, some oil is also drawn into the combustion chambers past the intake and exhaust valve
stem seals and burned.
The following is a partial list of conditions that can affect oil consumption rates:
zengine duty cycle
z operator driving habits
z ambient temperature
z quality and viscosity of the oil
Operation under varying conditions can frequently be misleading. A vehicle that has been run for
several thousand miles on short trips or in below- freezing ambient temperatures may have consumed
a "normal" amount of oil. However, when checking the engine oil level, it may measure up to the FULL
or MAX on the oil level dipstick due to dilution (condensation and fuel) in the engine crankcase. The
vehicle might then be driven at high speeds on the highway where the condensation and fuel boil off.
The next time the engine oil is checked, it may appear that a liter (quart) of oil was used in about 160
km (100 miles). This perceived 160 km (100 miles) per liter (quart) oil consumption rate causes
customer concern even though the actual overall oil consumption rate is about 2,400 km (1,500 miles)
per liter (quart).
Make sure the selected engine oil meets the current recommended API performance category with
SAE viscosity grade as shown in the vehicle Owner's Guide. It is also important that the engine oil is
changed at the intervals specified. Refer to the vehicle Owner's Guide.
Oil Pressure Test
1. Disconnect and remove the oil pressure sensor (9278) from the engine.
2. Connect the Oil Pressure Gauge to the oil pressure sender oil galley port.
3. Run the engine until normal operating temperature is reached.
4. Run the engine at the specified rpm and record the gauge reading.
5. The oil pressure should be within specifications; refer to the specification chart in the appropriate engine section.
6. If the pressure is not within specification, check the following possible sources: zinsufficient oil
z oil leakage
z worn or damaged oil pump
z oil pump screen cover and tube (6622)
z excessive main bearing clearance Klj . 13 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...