2003 FORD MUSTANG oil level

occurs on first
(morning) brake
application
pads.
Caused by humidity and
low disc brake pad
temperature.
z Squealing noise— a
continuous squeal z
Disc brake pads
or linings worn
below minimum
thickness. z
INSTALL new disc brake
pads. REFER to Section 206 - 03 for front disc brake
pads or Section 206 - 04 for
rear disc brake pads.
z Squealing noise— an
intermittent squeal
brought on by cold,
heat, water, mud or
snow z
Disc brake pad. zAcceptable condition.
z Groaning noise—
occurs at low speeds
with brake lightly
applied (creeping) z
Disc brake
pads. z
Acceptable condition.
z Grinding noise—
continuous z
Disc brake pads
or linings worn
below minimum
thickness. z
INSPECT the disc brake
pads, brake discs and
attaching hardware for
damage. REPAIR or
INSTALL new components
as necessary. REFER to
Section 206 - 03 for front
disc brakes and Section 206 - 04 for rear disc brakes.
z Moaning noise zBrake linings
contaminated
with grease or
oil. z
INSPECT the brake pads
and shoes for
contamination. REPAIR or
INSTALL new components
as necessary. REFER to
Section 206 - 03 for front
disc brakes or Section 206 -
04 for rear disc brakes.
z Brake
vibration/shudder—
occurs when brakes
are applied z
Uneven disc or
drum wear.
z Uneven disc
brake pad or
lining transfer.
z Suspension
components. z
Go To Pinpoint Test A .
z Brake
vibration/shudder—
occurs when the brake
pedal is released z
Brake drag. zINSPECT the disc brake
pads or linings for
premature wear. REPAIR
or INSTALL a new caliper
or wheel cylinder as
necessary. REFER to
Section 206 - 03 for front
disc brakes and Section 206 - 04 for rear disc brakes.
Symptom Chart—
Driveline Noise/Vibration Condition
Possible Sources Action
z Axle howling or
whine— front or rear
axle z
Axle lubricant
low. z
CHECK the lubricant level.
FILL the axle to
specification.
z Axle housing zINSPECT the axle housing Klj . 17 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Generator electrical
field or bearings. z
CARRY OUT generator
load test. REPAIR or
INSTALL a new generator
as necessary. REFER to
Section 414 - 02 .
z Drone type noise zExhaust system. zCARRY OUT the Exhaust System Neutralizing in this
section. REPAIR as
necessary.
z A/C compressor. zCHECK for noise with
vehicle at constant speeds.
CYCLE the compressor on
and off and listen for a
change in pitch. REPAIR as
necessary. REFER to
Section 412 - 03 .
z Powertrain mounts. zCARRY OUT the
Powertrain/Drivetrain Mount Neutralizing in this
section.
z Sputter type
noise— noise
worse when cold,
lessens or
disappears when
vehicle is at
operating
temperature z
Damaged or worn
exhaust system
components. z
INSPECT the exhaust
system for leaks or
damage. REPAIR as
necessary. REFER to
Section 309 - 00 .
z Rattling noise—
noise from the
upper engine
(valve train).
Worse when
engine is cold z
Low oil level. zCHECK oil level. FILL as
necessary.
z Thin or diluted oil. zINSPECT the oil for
contamination. If oil is
contaminated, CHECK for
the source. REPAIR as
necessary. CHANGE the oil
and filter.
z Low oil pressure. zCARRY OUT an oil
pressure test. If not within
specifications, REPAIR as
necessary. REFER to
Section 303 - 00 .
z Worn rocker
arms/fulcrums or
followers. z
CARRY OUT a valve train
analysis. INSTALL new
valve train components as
necessary. REFER to
Section 303 - 01A for 3.8L
engines or Section 303 - 01B
for 4.6L (2V) engines.
z Worn valve guides. zCARRY OUT a valve train
analysis. INSTALL new
valve guides as necessary.
REFER to Section 303 - 01A
for 3.8L engines or
Section 303 - 01B for 4.6L (2V)
engines. Klj . 26 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

information, REFER to
Section 205
- 00 .
REPAIR as necessary.
z Transmission
rumble/growl— noise at
all speeds in forward
gears, more
pronounced in a heavy
acceleration condition z
Damaged or worn
transmission
bearing or gears
(high mileage
vehicles). z
CHECK transmission
fluid for excessive
metal particles.
REPAIR as necessary.
REFER to Section 308 -
03A for T50D
transmissions or
Section 308 - 03B for
TR3650 transmissions.
z Transfer case whine—
noise at all ranges z
Incorrect fluid level
or fluid quality. z
CHECK that the
transfer case is filled to
the correct level and
with the specified fluid.
REFER to Section 308 -
03A for T50D
transmissions or
Section 308 - 03B for
TR3650 transmissions.
z Worn oil pump. zDISASSEMBLE the
transfer case. CHECK
the oil pump for wear or
damage. REPAIR as
necessary.
z Under- inflated or
oversized tires. z
CONFIRM that the tires
and wheels are correct
for the vehicle. CHECK
that the tire inflation
pressures are correct.
z Transfer case
growl/rumble— noise at
all ranges (A small
amount of planetary
noise can be heard
when the transfer case
is operated in low
range.) z
Damaged or worn
bearings or
planetary gear. z
DISASSEMBLE the
transfer case. CHECK
the bearings or
planetary gear for wear
or damage. REPAIR as
necessary.
z Transfer case
scraping/grating—
noise at all ranges z
Excessively
stretched drive
chain hitting the
case. z
DISASSEMBLE the
transfer case. CHECK
the drive chain for wear
or damage. REPAIR as
necessary.
z Transfer case
howl/hum— noise at all
ranges or high range
only z
Worn or damaged
sun (input) gear,
clutch pack
(intermediate) gear
or output shaft gear. z
DISASSEMBLE the
transfer case. CHECK
the gears for wear or
damage. REPAIR as
necessary.
z Transfer case
howl/hum— noise at
low range only z
Worn or damaged
intermediate gear
and sliding gears
(clutch pack). z
DISASSEMBLE the
transfer case. CHECK
the gears for wear or
damage. REPAIR as
necessary.
z Transfer case
vibration— vibration felt
with vehicle in 4WD z
Transfer case
mounting.
z Driveshaft out of
balance.
z Excessive pinion z
Go To Pinpoint Test M . Klj . 44 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Spring
Removal
CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number or an equivalent part must be installed, if installation is necessary. Do
not use a part of lesser quality or substitute design. Torque values must be used as specified
during reassembly to ensure proper retention of these parts.
1. Mark the front shock absorber (18124) relative to the protective sleeve with the vehicle in a static, level ground position (curb height).
2. Raise the vehicle on a hoist. For additional information, refer to Section 100 - 02 .
3. Remove the wheel and tire assembly. For additional information, refer to Section 204 - 04 .
4. Remove the cotter pin and nut. Discard the cotter pin.
SECTION 204-
01: Front Suspension 2003 Mustang Workshop Manual Special Tool(s)
Tie-
Rod End Remover
211- 001 (TOOL- 3290-D) or
Equivalent Coil Spring Compressor
204-
D001 (D78P-5310- A) or
Equivalent Klj . 1 ba
82003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Lower Arm
Removal
CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number must be installed if installation becomes necessary. If substitution is
necessary, the part must be of the same finish and property class. Torque values must be used
as specified during reassembly to make sure of correct retention of these parts.
1. Mark the rear shock absorber (18125) relative to the protective sleeve with the vehicle in a static, level ground position (curb height).
2. Remove the muffler assembly(ies). For additional information, refer to Section 309 - 00 .
3. Remove the rear spring (5560). For additional information, refer to Spring — Coil in this section.
4. Remove the lower suspension arm and bushing (5A649) from the body attachment. 1. Remove and discard the bolt and nut.
2. Remove the lower arm.
Installation 1. Install the lower suspension arm and bushing to the body attachment. 1. Position the lower arm. 2. Install a new bolt and a new nut. Do not tighten at this time. SECTION 204-
02: Rear Suspension 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Spring —
Coil
Removal CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number must be installed if installation becomes necessary. If substitution is
necessary, the part must be of the same finish and property class. Torque values must be used
as specified during reassembly to make sure of correct retention of these parts.
All vehicles
1. Mark the rear shock absorber (18125) relative to the protective sleeve with the vehicle in a static, level ground position (curb height).
2. Raise the vehicle. For additional information, refer to Section 100 - 02 .
3. Disconnect the anti- lock sensor wire.
SECTION 204-
02: Rear Suspension 2003 Mustang Workshop Manual Special Tool(s)
Hi-
Lift Jack
014- 00942 or Equivalent Klj . 1 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Repair the axle as necessary. Make sure the axle lubricant is at the correct level. Refer to
Specifications in this section.
Axle Vent
NOTE:
If a plugged vent cannot be cleared, install a new one.
A plugged vent will cause excessive seal lip wear due to internal pressure buildup. If a leak occurs,
check the vent. Make sure the vent hose is not kinked. Remove the hose from the vent nipple and
clear the hose of any foreign material. While the hose is removed, pass a length of mechanics wire in
and out of the vent to clean it. Connect the hose when done.
Flange Yoke Seal
Leaks at the axle drive pinion seal originate for the following reasons:
zSeal was not correctly installed.
z Poor quality seal journal surface.
Any damage to the seal bore (dings, dents, gouges, or other imperfections) will distort the seal casing
and allow leakage past the outer edge of the axle drive pinion seal.
The axle drive pinion seal can be torn, cut, or gouged if it is not installed carefully. The spring that
holds the axle drive pinion seal against the pinion flange may be knocked out and allow leakage past
the lip.
The rubber lips can occasionally become hard (like plastic) with cracks at the oil lip contact point. The
contact point on the pinion flange may blacken, indicating excessive heat. Marks, nicks, gouges, or
rough surface texture on the seal journal of the pinion flange will also cause leaks.
When a seal leak occurs, install a new seal and check the vent and the vent hose to make sure they
are clean and free of foreign material.
Axle Shaft Seals
Axle shaft oil seals are susceptible to the same kinds of damage as axle drive pinion seals if incorrectly
installed. The seal bore must be clean and the lip handled carefully to avoid cutting or tearing it. The
axle shaft journal surface must be free of nicks, gouges, and rough surface texture.
Differential Seals
Refer to Section 205 - 02A or
Section 205 - 02B .
Analysis of Vibration WARNING: A vehicle equipped with a Traction- Lok® differential will always have both
wheels driving. If only one wheel is raised off the floor and the rear axle is driven by the engine,
the wheel on the floor could drive the vehicle off the stand or jack. Be sure both rear wheels are
off the floor.
Few vibration conditions are caused by the rear axle. On a vibration concern, follow the diagnosis
procedure in Section 100 - 04 unless there is a good reason to suspect the axle.
Tires Klj . 3 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

SPECIFICATIONS
a
In- vehicle repair refill capacities are determined by filling the rear axle with the specified lubricant to
6.4- 14.3- mm (1/4- 9/16-in) below the bottom of the fill hole.
SECTION 205-
02A: Rear Drive Axle/Differential — Ford 7.5-Inch Ring
Gear 2003 Mustang Workshop
Manual General Specifications
Item Specification
Lubes and Sealers
SAE 80W-
90 Premium Rear Axle Lubricant XY-
80W90- QL WSP-
M2C197- A Premium Long-
Life Grease XG -1-C ESA-
M1C75- B Rust Penetrant and Inhibitor F2AZ-19A501-
A ESR-
M99C56- A High Temperature Nickel Anti-
Sieze Lubricant
F6AZ- 9L494- AA ESE-
M124A- A Clear Silicone Rubber F7AZ-
19554-CA ESB-
M4G92- A Threadlock and Sealer EOAZ-19554-
AA WSK-
M2G351- A5 Lubricant Fill Level Checks
Approximate axle fill capacity
a 1.54-1.66-
liters (3.25-3.50- pints)
6.4-14.3- mm (1/4-9/16- in) below the bottom of
the fill hole Clearance, Tolerance and Adjustments
Maximum ring gear back face runout 0.102 mm (0.004 in)
Maximum differential case runout 0.076 mm (0.003 in)
Differential side gear thrust washer thickness 0.762 mm -
0.813 mm (0.030 in - 0.032 in) Differential pinion gear thrust washer thickness 0.762 mm -
0.813 mm (0.030 in - 0.032 in) Maximum axle shaft end play 0.762 mm (0.030 in)
Ring gear backlash 0.203 mm-
0.381 mm
(0.008 in- 0.015 in)
[(0.305 mm- 0.381 mm
(0.012 in- 0.015 in) preferred] Variation between teeth maximum backlash 0.102 mm (0.004 in)
Pinion flange runout 0.25 mm (0.010 in) T.I.R.
Torque Specifications Description Nm lb-
ft lb-
in Bolt retaining the differential pinion shaft to the differential case 30 22 —
Bolt retaining the driveshaft yoke to the pinion flange 112 83 —
Bolt retaining the differential housing cover to the differential housing 44 32 —
Oil filler plug 30 22 —
Pinion bearing preload (used pinion bearings) 0.9-
1.5 — 8-
14 Pinion bearing preload (new pinion bearings) 1.8-
3.3 — 16-
29 Adapter for 205-
S127 2.2 — 20 Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...