2003 FORD MUSTANG oil filter

z
If equipped, inspect automatic transmission fluid level with dipstick.
z Inspect brake pads, shoes, rotors, drums, brake lines, hoses and parking brake system.
z Inspect wheel ends for end play and noise.
z Inspect engine cooling system and hoses.
z Inspect steering linkage, suspension and (if equipped) driveshaft and ball joints.
z Rotate tires and inspect for wear.
z Install a new cabin air filter.
z If filled with green engine coolant, change coolant.
224,000 Km (140,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect tires for wear. Rotation recommended for optimal tire life.
232,000 Km (145,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect tires for wear. Rotation recommended for optimal tire life.
240,000 Km (150,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect brake pads, shoes, rotors, drums, brake lines, hoses and parking brake system.
z Inspect wheel ends for end play and noise.
z Inspect engine cooling system and hoses.
z Inspect exhaust system and heat shields.
z Inspect steering linkage, suspension and (if equipped) driveshaft and ball joints.
z Rotate tires and inspect for wear.
z Install a new engine air filter.
z Install a new fuel filter. (See ADDITIONAL INFORMATION below.)
z If equipped, install a new cabin air filter.
z If filled with yellow engine coolant, change coolant or at 8 years, whichever comes first.
z Change automatic transmission/transaxle fluid and filter.
z Change rear axle lubricant on all rear wheel (RWD) vehicles.
z Install a new accessory drive belt(s) (if a new belt has not been installed within the last 100,000
miles).
z If equipped, install new climate controlled seat filters (Navigator, Lincoln LS and Aviator).
ADDITIONAL INFORMATION: If vehicle is registered in California, the California Air Resources Board
(CARB) has determined that failure to install a new fuel filter at this interval will not nullify the emission
warranty or limit recall liability prior to completion of the vehicle's useful life. It is, however
recommended that maintenance checks be carried out and recorded at the indicated intervals.
Additional checks for natural gas and propane vehicles include inspecting fuel tanks, as well as
draining and installing a new filter. Klj . 9 ba
112003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Generator electrical
field or bearings. z
CARRY OUT generator
load test. REPAIR or
INSTALL a new generator
as necessary. REFER to
Section 414 - 02 .
z Drone type noise zExhaust system. zCARRY OUT the Exhaust System Neutralizing in this
section. REPAIR as
necessary.
z A/C compressor. zCHECK for noise with
vehicle at constant speeds.
CYCLE the compressor on
and off and listen for a
change in pitch. REPAIR as
necessary. REFER to
Section 412 - 03 .
z Powertrain mounts. zCARRY OUT the
Powertrain/Drivetrain Mount Neutralizing in this
section.
z Sputter type
noise— noise
worse when cold,
lessens or
disappears when
vehicle is at
operating
temperature z
Damaged or worn
exhaust system
components. z
INSPECT the exhaust
system for leaks or
damage. REPAIR as
necessary. REFER to
Section 309 - 00 .
z Rattling noise—
noise from the
upper engine
(valve train).
Worse when
engine is cold z
Low oil level. zCHECK oil level. FILL as
necessary.
z Thin or diluted oil. zINSPECT the oil for
contamination. If oil is
contaminated, CHECK for
the source. REPAIR as
necessary. CHANGE the oil
and filter.
z Low oil pressure. zCARRY OUT an oil
pressure test. If not within
specifications, REPAIR as
necessary. REFER to
Section 303 - 00 .
z Worn rocker
arms/fulcrums or
followers. z
CARRY OUT a valve train
analysis. INSTALL new
valve train components as
necessary. REFER to
Section 303 - 01A for 3.8L
engines or Section 303 - 01B
for 4.6L (2V) engines.
z Worn valve guides. zCARRY OUT a valve train
analysis. INSTALL new
valve guides as necessary.
REFER to Section 303 - 01A
for 3.8L engines or
Section 303 - 01B for 4.6L (2V)
engines. Klj . 26 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Is the ticking noise gone? CHECK for TSB for applicable vehicle.
REPAIR as necessary. TEST the system
for normal operation.
No
GO to
B2 .
B2 CHECK FOR TICKING NOISE AT THE FUEL
INJECTOR z
Using an EngineEAR, listen at the fuel
injectors by placing a probe on each injector.
To isolate the faulty injector, disconnect the
injector electrical connector and listen for the
noise.
z Is the fuel injector the source of the ticking
noise? Yes
INSTALL a new fuel injector. REFER to
Section 303
- 04A for 3.8L engines or
Section 303 - 04B for 4.6L (2V) engines.
TEST the system for normal operation.
No
GO to B3 .
B3 CHECK THE BELT TENSIONER FOR TICKING
NOISE z
Inspect the accessory drive. Check for the belt
tensioner bottoming at end of travel or not at
end of stroke.
z Using an EngineEAR, listen at the belt
tensioner.
z Is the belt tensioner the source of the
noise? Yes
INSTALL a new belt tensioner. TEST the
system for normal operation.
No
GO to
B4 .
B4 CHECK THE WATER PUMP FOR TICKING
NOISE z
Using an EngineEAR, listen at the water pump
for ticking noise.
z Is the water pump the source of the noise? Yes
INSTALL a new water pump. REFER to
Section 303
- 03A . TEST the system for
normal operation.
No
GO to B5 .
B5 CHECK FOR AN OBSTRUCTION OF THE
COOLING FAN z
Inspect the cooling fan for obstructions.
z Check the cooling fan and shroud for wear or
damage.
z Was there an obstruction or does the
cooling fan show signs of damage? Yes
REPAIR or INSTALL a new cooling fan.
REFER to
Section 303 - 03A . TEST the
system for normal operation.
No
GO to B6 .
B6 CHECK THE OIL PUMP FOR TICKING NOISE
z
Check the oil pump using EngineEARs and
probe at the oil filter adapter to verify the oil
pump as a source.
z Is the oil pump the source of the noise? Yes
INSTALL a new oil pump. REFER to
Section 303
- 01A for 3.8L engines or
Section 303 - 01B for 4.6L (2V) engines.
TEST the system for normal operation.
No
GO to B7 .
B7 CHECK VALVE LIFTERS OR LASH
ADJUSTERS FOR CORRECT OPERATION z
Check valve lifter/lash adjuster for correct
operation, using EngineEARs.
z Are the valve lifters/lash adjusters Yes
VERIFY customer concern. CONDUCT a
diagnosis of other suspect components. Klj . 50 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST F: HYDRO-
BOOST ERRATIC OPERATION, STICKS,
BINDS OR GRABS z
Check accessory drive belt tension and
condition. Refer to Section 303 - 05 .
z Is the accessory drive belt OK? Yes
GO to
E3 .
No
INSTALL a new accessory drive belt.
REFER to Section 303 - 05 .
E3 CHECK POWER STEERING HOSES
z
Check power steering pressure hoses, power
steering gear pressure hoses and power
steering return hose for cracks or leaks.
z Do power steering pressure hose, power
steering gear hose and power steering
return hose check OK? Yes
GO to
E4 .
No
INSTALL new hoses as necessary.
REFER to Section 211 - 00 .
E4 CHECK BRAKE PEDAL LINKAGE
z
Check brake pedal linkage for binding or
sticking operation.
z Does pedal linkage check OK? Yes
GO to
E5 .
No
INSTALL new pedal linkage as necessary.
REFER to Section 206 - 06 .
E5 CHECK POWER STEERING PUMP SPEED
z
Check engine idle speed against
specifications.
z Is engine idle speed OK? Yes
GO to
E6 .
No
SET engine idle speed to specification.
REFER to Powertrain Control/Emissions
Diagnosis (PC/ED) manual. E6 CHECK FOR PLUGGED RETURN HOSE
z
NOTE: The return hose from the oil cooler to
the power steering reservoir has an in- line
filter in the hose.
z Disconnect power steering return hose from
power steering fluid cooler and power
steering pump reservoir.
z Pass air through hose from the oil cooler end.
z Is hose plugged? Yes
INSTALL a new power steering return
hose.
No
GO to
E7 .
E7 CHECK POWER STEERING PUMP FLOW
AND RELIEF z
Test power steering pump for correct flow
and relief pressure. Refer to Section 211 - 00 .
z Is power steering pump operating
correctly? Yes
INSTALL a new power brake hydro-
boost
unit. REFER to Section 206 - 07 .
No
INSTALL a new power steering pump.
REFER to Section 211 - 02 .
Test Step Result / Action to
Take F1 CHECK SUPPLY HOSE
z
Check for obstructions in power steering return hose and Yes Klj . 11 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
intake manifold gaskets
z cylinder head gaskets
z oil bypass filter
z oil filter adapter
z engine front cover
z oil filter adapter and filter body
z oil level indicator tube connection
z oil pressure sensor
Leakage Points— Under Engine—With Vehicle on Hoist
z oil pan gaskets (6710)
z oil pan sealer
z oil pan rear seal (6723)
z engine front cover gasket
z crankshaft front seal (6700)
z crankshaft rear oil seal (6701)
z crankshaft main bearing cap side bolts
z oil filter adapter and filter body
z oil cooler, if equipped
Leakage Points— With Transmission and Flywheel Removed
z crankshaft rear oil seal
z rear main bearing cap parting line
z rear main bearing cap and seals
z flywheel mounting bolt holes (with flywheel [6375] installed)
z camshaft rear bearing covers (6266) or pipe plugs at the end of oil passages
Oil leaks at crimped seams in sheet metal parts and cracks in cast or stamped parts can be detected
when using the dye method.
Compression Test— Compression Gauge Check
1. Make sure the oil in the crankcase is of the correct viscosity and at the correct level and that the battery (10655) is correctly charged. Operate the vehicle until the engine is at normal operating
temperature. Turn the ignition switch to the OFF position, then remove all the spark plugs
(12405).
2. Set the throttle plates in the wide- open position.
3. Install a compression gauge such as the Compression Tester in the No. 1 cylinder.
4. Install an auxiliary starter switch in the starting circuit. With the ignition switch in the OFF position, and using the auxiliary starter switch, crank the engine a minimum of five compression
strokes and record the highest reading. Note the approximate number of compression strokes Klj . 7 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

6. Carry out an oil consumption test:
a. Drain the engine oil, remove the oil bypass filter (6714) and refill with one liter (quart) less than
the recommended amount.
b. Run the engine for three minutes (10 minutes if cold), and allow the oil to drain back for at least five minutes with the vehicle on a level surface.
c. Remove oil level dipstick and wipe clean. (Do not wipe with anything contaminated with silicone compounds.) Reinstall the oil level dipstick, being sure to seat it firmly in the oil level indicator
tube (6754). Remove the oil level dipstick and draw a mark on the back (unmarked) surface at
the indicated oil level. This level should be about the same as the MIN or ADD mark on the face
of the oil level dipstick.
d. Add one liter (quart) of oil. Restart the engine and allow to idle for at least two minutes. Shut off the engine and allow the oil to drain back for at least five minutes. Mark the oil level dipstick,
using the procedure above.
e. Record the vehicle mileage. f. Instruct the customer to drive the vehicle as usual and perform the following:
„Check the oil level regularly at intervals of 160 to 240 km (100- 150 miles).
„ Return to the service point when the oil level drops below the lower (MIN or ADD) mark
on the oil level dipstick.
„ Add only full liters (quarts) of the same oil in an emergency. Note the mileage at which
the oil is added.
g. Check the oil level under the same conditions and at the same location as in Steps 6c and 6d.
„Measure the distance from the oil level to the UPPER mark on the oil level dipstick and
record.
„ Measure the distance between the two scribe marks and record.
„ Divide the first measurement by the second.
„ Divide the distance driven during the oil test by the result. This quantity is the
approximate oil consumption rate in kilometers per liter or in miles per quart.
h. If the oil consumption rate is unacceptable, go to Step 7.
7. Check the positive crankcase ventilation (PCV) system. Make sure the system is not plugged.
8. Check for plugged oil drain- back holes in the cylinder heads and cylinder block.
9. If the condition still exists after performing the above steps, go to Step 10.
10. Perform a cylinder compression test or perform a cylinder leak detection test with Engine Cylinder Leak Detection/Air Pressurization Kit. This can help determine the source of oil
consumption such as valves, piston rings or other areas.
11. NOTE: After determining if new parts should be installed, make sure correct parts are used.
Check valve guides for excessive guide clearance. Install new all valve stem seals (6571) after
verifying valve guide clearance.
12. Worn or damaged internal engine components can cause excessive oil consumption. Small deposits of oil on the tips of spark plugs can be a clue to internal oil consumption. If internal oil
consumption still persists, proceed as follows:
a. Remove the engine from the vehicle and place it on an engine work stand. Remove the intake manifolds (9424), cylinder heads, oil pan (6675) and oil pump (6600).
b. Check piston ring clearance, ring gap and ring orientation. Repair as necessary.
c. Check for excessive bearing clearance. Repair as necessary.
13. Repeat the oil consumption test (Step 6) to confirm the oil consumption concern has been resolved. Klj . 10 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

SPECIFICATIONS
SECTION 303-
01A: Engine — 3.8L 2003 Mustang Workshop Manual General Specifications
Item Specification
Lubricants and Sealants
SAE 5W-
20 Premium Synthetic Blend Motor Oil
XO- 5W20- QSP WSS-
M2C153- H Gasket and Trim Adhesive F3AZ-19B508-
AA ESE-
M2G52- A Pipe Sealant with Teflon® D8AZ-19554-
A WSK-
M2G350- A2 Silicone Gasket and Sealant F7AZ-19554-
EA WSE-
M4G323- A4 Metal Surface Cleaner F4AZ-19A536-
RA WSE-
M5B392- A Engine
Displacement 3.8L
Number of cylinders 6
Bore 96.8325 mm (3.81 in)
Stroke 86.0 mm (3.39 in)
Firing order 1-4-2-5-3-
6 Oil pressure (hot 2,500 rpm) 40-
125 psi Oil capacity 5 quarts w/filter change
Compression ratio —
Cylinder Head and Valve Train
Cylinder head gasket surface flatness 0.18 mm (0.007 in)
Combustion chamber volume 61.5-
64.5 cc Valve arrangement (front to rear) —
Valve guide bore diameter 7.015-
7.044 mm (0.276- 0.277 in) Valve stem diameter —
intake 6.955-
6.988 mm (0.2738- 0.2751 in) Valve stem diameter —
exhaust 6.929-
6.962 mm (0.2728- 0.2741 in) Valve stem diameter —
oversize (intake) 9.075-
9.055 mm (0.3573- 0.3565 in) Valve stem diameter —
oversize (exhaust) 9.063-
9.043 mm (0.3568- 0.3560 in) Valve stem diameter —
oversize (intake) 9.456-
9.436 mm (0.3723- 0.3715 in) Valve stem diameter —
oversize (exhaust) 9.444-
9.424 mm (0.3718- 0.3710 in) Valve stem-
to-guide clearance — intake 0.020-
0.069 mm (0.045- 0.090 in) Valve stem-
to-guide clearance — exhaust 0.038-
0.083 mm (0.0015- 0.0033 in) Valve head diameter —
intake 47.27 mm (1.86 in)
Valve head diameter —
exhaust 37.1 mm (1.46 in)
Valve face runout 0.05 mm (0.002 in)
Valve face angle 45.675 degrees
Valve seat width 1.5-
2.0 mm (0.06- 0.08 in) Valve seat runout (T.I.R.) 0.076 mm (0.003 in) Klj . 1 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

A/C compressor bracket-
to-cylinder head stud bolt 25 18 —
Oil level indicator tube-
to-cylinder head bolt 10 — 89
Coolant recovery reservoir bracket-to-
GOP bolts 9 — 80
Motor mount-
to-subframe nuts 115 85 —
Oil pan drain plug 26 19 —
Wire harness bracket to motor mount nut 27 20 —
Steering column pinch bolt 47 35 —
Front subframe-
to-body bolts 90 66 —
Front subframe-
to-shock tower bolts 115 85 —
Oil pan-to-
cylinder block bolts a — — —
Oil pan-to-
transmission bell housing 45 33 —
Main bearing bridge nuts 32 24
Oil pump cover-
to-engine front cover bolts 25 18 —
Oil pump cover-
to-engine front cover bolt 10 89 —
Oil pickup tube-
to-cylinder block bolts 25 18 —
Oil pickup tube-
to-oil pan baffle nut 48 35 —
Flywheel-
to-crankshaft bolts 80 59 —
Wire harness bracket-
to-motor mount stud- nut 27 20 —
Engine ground strap-
to-motor mount nut 27 20 —
Motor mount-
to-motor mount bracket bolts 70 52 —
RH motor mount-
to-motor mount bracket nut 70 52 —
Hood ground strap-
to-hood hinge bolt 12 9 —
Hood hinge nuts 12 9 —
Generator mounting bracket 25 18 —
Power steering pump bracket nuts 8 — 71
Power steering pump bolts 25 18 —
Valve tappet guide plate bolts 12 9 —
Generator positive cable nut 10 — 89
Power steering pressure tube to pump nut 40 30 —
Accelerator cable bracket-
to-intake manifold bolts 10 — 89
42-
pin connector bolt 10 — 89
Transmission oil cooler tube bracket-
to-motor mount bracket nut 27 20
Torque converter-
to-flywheel nuts 36 27 —
Engine-
to-transmission bolts 40 30 —
Engine mount bracket-
to-engine bolts 70 52 —
Engine mount bracket-
to-engine nuts 70 52 —
Water pump pulley bolts 25 18 —
Oil filter
b — — —
Upper intake manifold-
to-lower intake manifold bolts a — — —
Lower intake manifold-
to-cylinder head bolts a — — —
Rocker arm pivot-
to-cylinder head bolts a — — — Klj . 5 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...