2003 FORD MUSTANG manual transmission

69. Lower the vehicle.
Manual transmission vehicles 70. Remove the two screws and position the clutch cable aside.
All vehicles 71. Attach the special tool to a floor crane and the engine, and remove the engine from the vehicle. Klj . 18 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Disassembly
Manual transmission vehicles
1. Remove the clutch and pressure plate. For additional information, refer to Section 308 - 02 .
2. Remove the flywheel.
Automatic transmission vehicles 3. Remove the flexplate. For additional information, refer to Flexplate in this section.
All vehicles 4. Using the special tool, remove the rear oil slinger. 303-
567 (T97P-6565- AH) Remover, Crankshaft Front Oil
Seal
303-
107 (T74P-6700- A) Klj . 2 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

83. Using the special tool, install the crankshaft rear main seal.
84. Using the special tools, install the crankshaft oil slinger.
Automatic transmission vehicles 85. Install the flexplate and install the bolts in the sequence shown. Klj . 28 ba
302003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Manual transmission vehicles
86. Install the flywheel and the bolts in the sequence shown.
87. Install the clutch and pressure plate. For additional information, refer to Section 308 - 02 . Klj . 29 ba
302003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Manual transmission vehicles
2. Install the clutch cable and retaining screws.
All vehicles 3. Raise and support the vehicle. For additional information, refer to Section 100 - 02 .
4. Connect the transmission wiring harness. 1. Connect the RH oxygen sensor connector retainer.
2. Connect the transmission harness electrical connector.
5. NOTE: RH side shown, LH side similar.
Install the LH and RH engine mount nuts. Klj . 2 ba
182003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Manual transmission vehicles
6. Lubricate the ball stud, clutch release lever and the input shaft with clean engine oil.
All vehicles 7. Raise the transmission and install the seven bolts.
8. Install the bolts. Klj . 3 ba
182003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

9. Install the transmission crossmember and the bolts.
10. Remove the transmission jack.
Manual transmission vehicles 11. Install the clutch cable and the clutch cable retainer.
12. Attach the clutch release cable to the clutch release fork. Klj . 4 ba
182003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

13. Install the clutch release lever cover and bolt.
All vehicles 14. Connect the output shaft speed (OSS) sensor electrical connector and attach the left and right oxygen sensor electrical connectors to the crossmember.
15. Connect the reversing lamp switch electrical connector and the wiring harness to the transmission.
16. Remove the two bolts from the RH lifting bracket. Klj . 5 ba
182003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...