2003 FORD MUSTANG radiator

All vehicles
8. Remove the nuts and disconnect the lines. zDiscard the O- ring seals.
Vehicles with 4WABS 9. Remove the hydraulic control unit upper bracket bolts.
10. Raise the vehicle.
11. Remove the hydraulic control unit lower bracket bolt and position the hydraulic control unit aside.
12. Lower the vehicle.
All vehicles 13. Remove the bolts and the radiator brackets. Klj . 3 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

14. Position the radiator rearward.
15. Remove the pin-
type retainers.
16. Position the wiring harness rearward. 17. Remove the condenser bolts. Klj . 4 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

SPECIFICATIONS
SECTION 414-
01: Battery, Mounting and Cables 2003 Mustang Workshop Manual General Specifications
Item Specification
Manufacturer Motorcraft
Voltage 12 volt
Amps at -
17.7°C (0°F) cold crank 540
Minutes—
reserve capacity 100
Amps/hrs.—20 hour rate 55
Location Left front of engine compartment
Torque Specifications Description Nm lb-
ft lb-
in Battery cable harness front support bracket nut 25 18 —
Battery cable terminal bolts 7 — 62
Battery hold-
down bolt 10 — 89
Battery junction box nut 20 15 —
Battery tray bolts 11 8 —
Front lower cable harness bracket nuts 11 8 —
Generator B+ cable nut 8 — 71
Battery cable bracket nut (left upper) 25 18 —
Battery ground cable nut (engine block) 25 18 —
Battery ground cable at the radiator support bolt 12 9 —
Positive battery cable nut (starter solenoid) 12 9 —
Positive battery wire nut (starter solenoid) 6 — 53
Right engine mount cable harness bracket nut 25 18 — Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Battery Cables
Removal
WARNING: Batteries normally produce explosive gases which can cause personal injury.
Therefore, do not allow flames, sparks or lighted substances to come near the battery. When
charging or working near a battery, always shield your face and protect your eyes. Always
provide ventilation. Failure to follow these instructions may result in personal injury.
WARNING: Keep out of the reach of children. Batteries contain sulfuric acid. Avoid
contact with skin, eyes, or clothing. Also, shield your eyes when working near the battery to
protect against possible splashing of the acid solution. In case of acid contact with skin or
eyes, flush immediately with water for a minimum of 15 minutes and get prompt medical
attention. If acid is swallowed, call a physician immediately. Failure to follow these instructions
may result in personal injury.
All vehicles
1. Remove the battery. For additional information, refer to Battery in this section.
2. If equipped, unplug the engine heater intermediate connection.
3. Remove the battery ground cable harness bolt from the radiator support and release the cable harness locators.
4. Disconnect the battery cable harness electrical connectors.
5. CAUTION: The square terminal from the battery must be installed first, followed by
SECTION 414-
01: Battery, Mounting and Cables 2003 Mustang Workshop Manual Klj . 1 ba
62003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

13.
NOTE: 4.6L 2V shown; 3.8L and 4.6L 4V similar.
Remove the front lower cable harness bracket nuts.
14. Pull the harness assembly downward until it clears the engine/radiator area.
15. NOTE: 4.6L 2V shown; 3.8L and 4.6L 4V similar.
Remove the right engine mount cable harness bracket nut.
16. Remove the cover from the starter solenoid connections. Klj . 4 ba
62003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Front End Body Panels
The front end body panel components consist of the following:
zair deflectors
z cowl grille
z fenders
z fender splash shields
z hood
z hood hinges
z hood weatherstrip
z radiator grille opening panel
SECTION 501-
02: Front End Body Panels 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

Remove the lower fender bolts and, if equipped, remove the shims.
6. Through the door opening, remove the inner fender bolts.
7. Remove the radiator grille opening panel to fender bolts.
8. Remove the upper bolts and the fender.
9. NOTE: On the RH fender, feed the antenna cable through the fender opening.
To install, reverse the removal procedure. Klj . 2 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Radiator Grille Opening Panel
Removal and Installation
1. Remove the front bumper cover. For additional information, refer to Section 501 - 19 .
2. Remove the eight bolts (four on each side) and the radiator grille opening panel.
3. To install, reverse the removal procedure.
SECTION 501-
02: Front End Body Panels 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...