2003 FORD MUSTANG torque

SPECIFICATIONS
SECTION 211-
05: Steering Column Switches 2003 Mustang Workshop Manual Torque Specifications
Description Nm lb-
ft lb-
in Ignition switch screws 6 — 53
Instrument panel reinforcement screws 9 — 80
Instrument panel steering column cover screws 9 — 80
Key release button bolt 5 — 44 Klj . 1 ba
12003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

a
20- 200 seconds to leakdown 3.18 mm (0.125 in) with 225 Newtons (50 pounds) load and tappet filled
with leak- down fluid. —
desired Connecting rod bearing-
to-crankshaft clearance
— allowable 0.022-
0.069 mm (0.00086- 0.0027 in) Connecting rod side clearance 0.11-
0.49 mm (0.0047- 0.0193 in) Balance Shaft
Journal diameter 52.108-
52.082 mm (2.0515- 2.0505 in) Bore inside diameter 55.689-
55.664 mm (2.192- 2.191 in) Maximum runout 0.025 mm (0.001 in)
End play 0.075-
0.200 mm (0.003- 0.008 in)
Torque Specifications Description Nm lb-
ft lb-
in EGR transducer bracket-
to-intake manifold bolts 10 — 89
Ignition coil-
to-intake manifold bolts 6 — 53
Water outlet tube-
to-intake manifold stud bolt 10 — 89
EGR tube-
to-EGR valve nut 40 30 —
Water outlet tube-
to-front water pump bolt 10 — 89
Fuel supply manifold bolts 10 — 89
LH valve cover-
to-cylinder head bolts 10 — 89
LH valve cover-
to-cylinder head stud bolts 10 — 89
EGR tube-
to-exhaust manifold nut 40 30 —
RH valve cover-
to-cylinder head bolts 10 — 89
RH valve cover-
to-cylinder head stud bolts 10 — 89
Coolant recovery reservoir-
to-cylinder head stud bolts 10 — 89
Coolant recovery reservoir-
to-bracket bolts 5 — 44
Crankshaft pulley bolt 160 118 —
Camshaft position sensor bolts 3 — 27
Camshaft synchronizer-
to-front cover bolt 25 18 —
Front cover-
to-cylinder block bolts 25 18 —
Radiator fan shroud-
to-radiator bolts 9 — 80
Camshaft thrust plate-
to-cylinder block bolts 12 9 —
Camshaft synchronizer drive gear-
to-camshaft bolt 45 33 —
Timing chain tensioner-
to-cylinder block bolts 12 9 —
Exhaust manifold-
to-cylinder head nuts 33 24 —
Power steering pump bracket-
to-water pump nuts 20 15 —
Power steering pump bracket-
to-generator bracket bolts 20 15 —
Generator bracket-
to-cylinder head bolts 40 30 —
Exhaust manifold studs 8 — 71
A/C compressor bracket-
to-cylinder head bolts 48 35 —
A/C compressor bracket-
to-cylinder head nut 48 35 — Klj . 4 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

A/C compressor bracket-
to-cylinder head stud bolt 25 18 —
Oil level indicator tube-
to-cylinder head bolt 10 — 89
Coolant recovery reservoir bracket-to-
GOP bolts 9 — 80
Motor mount-
to-subframe nuts 115 85 —
Oil pan drain plug 26 19 —
Wire harness bracket to motor mount nut 27 20 —
Steering column pinch bolt 47 35 —
Front subframe-
to-body bolts 90 66 —
Front subframe-
to-shock tower bolts 115 85 —
Oil pan-to-
cylinder block bolts a — — —
Oil pan-to-
transmission bell housing 45 33 —
Main bearing bridge nuts 32 24
Oil pump cover-
to-engine front cover bolts 25 18 —
Oil pump cover-
to-engine front cover bolt 10 89 —
Oil pickup tube-
to-cylinder block bolts 25 18 —
Oil pickup tube-
to-oil pan baffle nut 48 35 —
Flywheel-
to-crankshaft bolts 80 59 —
Wire harness bracket-
to-motor mount stud- nut 27 20 —
Engine ground strap-
to-motor mount nut 27 20 —
Motor mount-
to-motor mount bracket bolts 70 52 —
RH motor mount-
to-motor mount bracket nut 70 52 —
Hood ground strap-
to-hood hinge bolt 12 9 —
Hood hinge nuts 12 9 —
Generator mounting bracket 25 18 —
Power steering pump bracket nuts 8 — 71
Power steering pump bolts 25 18 —
Valve tappet guide plate bolts 12 9 —
Generator positive cable nut 10 — 89
Power steering pressure tube to pump nut 40 30 —
Accelerator cable bracket-
to-intake manifold bolts 10 — 89
42-
pin connector bolt 10 — 89
Transmission oil cooler tube bracket-
to-motor mount bracket nut 27 20
Torque converter-
to-flywheel nuts 36 27 —
Engine-
to-transmission bolts 40 30 —
Engine mount bracket-
to-engine bolts 70 52 —
Engine mount bracket-
to-engine nuts 70 52 —
Water pump pulley bolts 25 18 —
Oil filter
b — — —
Upper intake manifold-
to-lower intake manifold bolts a — — —
Lower intake manifold-
to-cylinder head bolts a — — —
Rocker arm pivot-
to-cylinder head bolts a — — — Klj . 5 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Vehicle equipped with automatic transmission
33. Remove the access cover.
34. NOTE: Discard the torque converter nuts.
Disconnect the torque converter (7902). zRemove the four nuts.
35. Remove the oil pan- to-transmission bolts. Klj . 8 ba
112003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Vehicles equipped with automatic transmission
9. Install the five bellhousing upper bolts.
10. Install the bolts.
11. Install the four torque converter nuts.
All vehicles Klj . 3 ba
102003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

e
Specification in 90.200 mm diameter gauge.
f If applicable, measured vertically, +0.030- 0.050 mm (0.001-0.002 inch) measured horizontally (oval
pin bore).
g Pin bore and crank bearing bore must be parallel and in same vertical plane within the specified total
difference when measured at the ends of a 203 mm bar, 101.5 mm on each side of rod centerline.
Torque Specifications Description Nm lb-
ft lb-
in Main bearing cap adjusting bolts
a — — —
EGR sensor bracket 10 — 89
Belt idler pulley 25 18 —
Oil filter 15 11 —
Oil filter adapter insert 58 43 —
Camshaft sprocket bolt
a — — —
Connecting rod bolt
a — — —
Engine mount nuts 150 111 —
Engine mount-
to-cylinder block bolts 70 52 —
Exhaust manifolds
a — — —
Engine front cover bolts
a — — —
Drive belt tensioner bolts 25 18 —
A/C muffler 20 15 —
Battery cable support brackets 20 15 —
Cylinder head bolt
a — — —
Pulley-
to-crankshaft bolt a — — —
EGR valve to intake manifold 25 18 —
EGR valve tube to exhaust manifold fittings 40 30 —
Intake manifold-
to-cylinder head bolt 25 18 —
Main bearing cap bolt
a — — —
Oil filter adapter bolts 25 18 —
Oil level indicator tube bolt 10 — 89
Oil pump screen cover and tube-
to-oil pump bolt 10 — 89
Oil pan-to-
cylinder block bolt a — — —
Flywheel 80 59
Oil pan-to-
engine front cover bolts a — — —
Oil pump-
to-cylinder block bolt 10 — 89
Oil pump screen cover and tube-
to-main bearing cap stud spacer bolt 25 18 —
Water pump pulley bolts 25 18 —
Cam cover bolt
a — — —
Water pump-
to-cylinder block bolt 25 18 —
Water bypass tube 25 18 —
EGR tube nuts (2 req'd) 40 30 —
Power steering pump to engine 25 18 — Klj . 4 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

a
Refer to the procedure in this section. Power steering reservoir bolts 10 — 89
Water outlet connector bolts 25 18 —
Camshaft cap cluster to cylinder head bolts 10 — 89
Torque converter nuts 25 18 —
Timing chain tensioner bolts 25 18 —
Transmission filler tube bolt 47 35 —
A/C compressor bolts 25 18 —
Ignition coil bolts 6 — 53
Generator brace bolts 10 — 89
Primary timing chain guide-
to-engine bolts 10 — 89
Accelerator cable bracket bolts 10 — 89
Rear seal retainer bolts 10 — 89
Pressure plate bolts 2 — 47
Spark plugs 18 13 —
Crankshaft timing bolt sensor assembly 10 — 89
Camshaft timing bolt sensor assembly 10 — 89
Fuel rail studs 10 — 89
Engine coolant sensor 15 11 —
Exhaust manifold—
stud to cylinder head 10-
13 7-10 —
Throttle body adaptor bolts
a — — —
Throttle body bolts 10 — 89
Idle air control valve 10 — 89
RFI capacitor nut 10 — 89
Generator bolts 25 18 —
Oil pan drain plug 14 10 —
Water bypass tube bracket bolt 25 18 —
Subframe bolts 115 85 —
Battery lead to generator 10 — 89
EGR vacuum regulator solenoid bracket 10 — 89
Pipe plug—
water drain 20 15 —
Screen and cover assembly to main bearing cap stud spacer 25 18 —
Wiring harness retainer nut 10 — 89
Oil pressure switch
a — — —
A/C muffler stud to cylinder head 10 — 89
EGR tube to exhaust manifold connector 50 37 — Klj . 5 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

NOTE:
Only one connecting rod assembly shown, others similar.
Using the special tool install the piston and connecting rod assembly by pushing the pistons
through the top of the cylinder block.
21. NOTE: These bolts are torque- to-yield. Install new bolts each time they are serviced.
Install the connecting rod bearing caps and bolts and tighten in three stages. zStage 1: Tighten to 25Nm (18 lb- ft).
z Stage 2: Tighten to 40Nm (30 lb- ft).
z Stage 3: Tighten an additional 90 degrees.
22. Rotate the crankshaft and install the remaining piston and connecting rod assemblies.
23. Check the connecting rod bearing clearance. For additional information, refer to Section 303 -
00 .
24. Install the oil pump and tighten the bolts. 25. NOTE: Install a new O - ring if necessary. Klj . 11 ba
362003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...