2003 DODGE RAM Output speed sensor

pump by drawing air into the pump cavity and also
closes the vent seal. During non test conditions the
vent seal is held open by the pump diaphragm
assembly which pushes it open at the full travel posi-
tion. The vent seal will remain closed while the
pump is cycling due to the reed switch triggering of
the three port solenoid that prevents the diaphragm
assembly from reaching full travel. After the brief
initialization period, the solenoid is de-energized
allowing atmospheric pressure to enter the pump
cavity, thus permitting the spring to drive the dia-
phragm which forces air out of the pump cavity and
into the vent system. When the solenoid is energized
and de energized, the cycle is repeated creating flow
in typical diaphragm pump fashion. The pump is con-
trolled in 2 modes:
Pump Mode: The pump is cycled at a fixed rate to
achieve a rapid pressure build in order to shorten the
overall test length.
Test Mode: The solenoid is energized with a fixed
duration pulse. Subsequent fixed pulses occur when
the diaphragm reaches the Switch closure point.
The spring in the pump is set so that the system
will achieve an equalized pressure of about 7.5º H20.
The cycle rate of pump strokes is quite rapid as the
system begins to pump up to this pressure. As the
pressure increases, the cycle rate starts to drop off. If
there is no leak in the system, the pump would even-
tually stop pumping at the equalized pressure. If
there is a leak, it will continue to pump at a rate rep-
resentative of the flow characteristic of the size of the
leak. From this information we can determine if the
leak is larger than the required detection limit (cur-
rently set at .040º orifice by CARB). If a leak is
revealed during the leak test portion of the test, the
test is terminated at the end of the test mode and no
further system checks will be performed.
After passing the leak detection phase of the test,
system pressure is maintained by turning on the
LDP's solenoid until the purge system is activated.
Purge activation in effect creates a leak. The cycle
rate is again interrogated and when it increases due
to the flow through the purge system, the leak check
portion of the diagnostic is complete.
The canister vent valve will unseal the system
after completion of the test sequence as the pump
diaphragm assembly moves to the full travel position.
Evaporative system functionality will be verified by
using the stricter evap purge flow monitor. At an
appropriate warm idle the LDP will be energized to
seal the canister vent. The purge flow will be clocked
up from some small value in an attempt to see a
shift in the 02 control system. If fuel vapor, indicated
by a shift in the 02 control, is present the test is
passed. If not, it is assumed that the purge system isnot functioning in some respect. The LDP is again
turned off and the test is ended.
MISFIRE MONITOR
Excessive engine misfire results in increased cata-
lyst temperature and causes an increase in HC emis-
sions. Severe misfires could cause catalyst damage.
To prevent catalytic convertor damage, the PCM
monitors engine misfire.
The Powertrain Control Module (PCM) monitors
for misfire during most engine operating conditions
(positive torque) by looking at changes in the crank-
shaft speed. If a misfire occurs the speed of the
crankshaft will vary more than normal.
FUEL SYSTEM MONITOR
To comply with clean air regulations, vehicles are
equipped with catalytic converters. These converters
reduce the emission of hydrocarbons, oxides of nitro-
gen and carbon monoxide. The catalyst works best
when the Air Fuel (A/F) ratio is at or near the opti-
mum of 14.7 to 1.
The PCM is programmed to maintain the optimum
air/fuel ratio of 14.7 to 1. This is done by making
short term corrections in the fuel injector pulse width
based on the O2S sensor output. The programmed
memory acts as a self calibration tool that the engine
controller uses to compensate for variations in engine
specifications, sensor tolerances and engine fatigue
over the life span of the engine. By monitoring the
actual fuel-air ratio with the O2S sensor (short term)
and multiplying that with the program long-term
(adaptive) memory and comparing that to the limit,
it can be determined whether it will pass an emis-
sions test. If a malfunction occurs such that the PCM
cannot maintain the optimum A/F ratio, then the
MIL will be illuminated.
CATALYST MONITOR
To comply with clean air regulations, vehicles are
equipped with catalytic converters. These converters
reduce the emission of hydrocarbons, oxides of nitro-
gen and carbon monoxide.
Normal vehicle miles or engine misfire can cause a
catalyst to decay. This can increase vehicle emissions
and deteriorate engine performance, driveability and
fuel economy.
The catalyst monitor uses dual oxygen sensors
(O2S's) to monitor the efficiency of the converter. The
dual O2S's sensor strategy is based on the fact that
as a catalyst deteriorates, its oxygen storage capacity
and its efficiency are both reduced. By monitoring
the oxygen storage capacity of a catalyst, its effi-
ciency can be indirectly calculated. The upstream
O2S is used to detect the amount of oxygen in the
exhaust gas before the gas enters the catalytic con-
DREMISSIONS CONTROL 25 - 3
EMISSIONS CONTROL (Continued)

problem is repaired or ceases to exist, the PCM can-
cels the code after 40 warm-up cycles. Diagnostic
trouble codes that affect vehicle emissions illuminate
the Malfunction Indicator Lamp (MIL). The MIL is
displayed as an engine icon (graphic) on the instru-
ment panel. Refer to Malfunction Indicator Lamp in
this section.
Certain criteria must be met before the PCM
stores a DTC in memory. The criteria may be a spe-
cific range of engine RPM, engine temperature,
and/or input voltage to the PCM.
The PCM might not store a DTC for a monitored
circuit even though a malfunction has occurred. This
may happen because one of the DTC criteria for the
circuit has not been met.For example,assume the
diagnostic trouble code criteria requires the PCM to
monitor the circuit only when the engine operates
between 750 and 2000 RPM. Suppose the sensor's
output circuit shorts to ground when engine operates
above 2400 RPM (resulting in 0 volt input to the
PCM). Because the condition happens at an engine
speed above the maximum threshold (2000 rpm), the
PCM will not store a DTC.
There are several operating conditions for which
the PCM monitors and sets DTC's. Refer to Moni-
tored Systems, Components, and Non-Monitored Cir-
cuits in this section.
Technicians must retrieve stored DTC's by connect-
ing the DRB scan tool (or an equivalent scan tool) to
the 16±way data link connector. The connector is
located on the bottom edge of the instrument panel
near the steering column (Fig. 1).
NOTE: Various diagnostic procedures may actually
cause a diagnostic monitor to set a DTC. For
instance, pulling a spark plug wire to perform a
spark test may set the misfire code. When a repair
is completed and verified, connect the DRB scan
tool to the 16±way data link connector to erase all
DTC's and extinguish the MIL.
OPERATION - TASK MANAGER
The Task Manager determines which tests happen
when and which functions occur when. Many of the
diagnostic steps required by OBD II must be per-
formed under specific operating conditions. The Task
Manager software organizes and prioritizes the diag-
nostic procedures. The job of the Task Manager is to
determine if conditions are appropriate for tests to be
run, monitor the parameters for a trip for each test,
and record the results of the test. Following are the
responsibilities of the Task Manager software:
²Test Sequence
²MIL Illumination
²Diagnostic Trouble Codes (DTCs)
²Trip Indicator²Freeze Frame Data Storage
²Similar Conditions Window
Test Sequence
In many instances, emissions systems must fail
diagnostic tests more than once before the PCM illu-
minates the MIL. These tests are know as 'two trip
monitors.' Other tests that turn the MIL lamp on
after a single failure are known as 'one trip moni-
tors.' A trip is defined as 'start the vehicle and oper-
ate it to meet the criteria necessary to run the given
monitor.'
Many of the diagnostic tests must be performed
under certain operating conditions. However, there
are times when tests cannot be run because another
test is in progress (conflict), another test has failed
(pending) or the Task Manager has set a fault that
may cause a failure of the test (suspend).
²Pending
Under some situations the Task Manager will not
run a monitor if the MIL is illuminated and a fault is
stored from another monitor. In these situations, the
Task Manager postpones monitorspendingresolu-
tion of the original fault. The Task Manager does not
run the test until the problem is remedied.
For example, when the MIL is illuminated for an
Oxygen Sensor fault, the Task Manager does not run
the Catalyst Monitor until the Oxygen Sensor fault is
remedied. Since the Catalyst Monitor is based on sig-
nals from the Oxygen Sensor, running the test would
produce inaccurate results.
²Conflict
There are situations when the Task Manager does
not run a test if another monitor is in progress. In
Fig. 1 DATA LINK CONNECTOR LOCATION -
TYPICAL
1 - 16-WAY DATA LINK CONNECTOR
DREMISSIONS CONTROL 25 - 5
EMISSIONS CONTROL (Continued)

FLUID RESERVOIR - REMOVAL..........5-19
FLUID, SPECIFICATIONS - BRAKE.........5-18
FLUSH - SPECIFICATIONS, GAP.........23-95
FLUSHING - STANDARD PROCEDURE,
COOLING SYSTEM CLEANING/
REVERSE............................7-17
FLUSHING POWER STEERING SYSTEM -
STANDARD PROCEDURE...............19-39
FLYWHEEL - ASSEMBLY................6-12
FLYWHEEL - DIAGNOSIS AND TESTING....6-11
FLYWHEEL - DISASSEMBLY.............6-12
FLYWHEEL - INSTALLATION.............6-12
FLYWHEEL - REMOVAL.................6-12
FOG LAMP - INSTALLATION............8L-11
FOG LAMP - REMOVAL................8L-11
FOG LAMP RELAY - DESCRIPTION.......8L-11
FOG LAMP RELAY - DIAGNOSIS AND
TESTING, FRONT.....................8L-12
FOG LAMP RELAY - INSTALLATION......8L-13
FOG LAMP RELAY - OPERATION.........8L-12
FOG LAMP RELAY - REMOVAL..........8L-13
FOOTMANS LOOP BRACKETS -
INSTALLATION, SEAT BACK REAR.......23-85
FOOTMANS LOOP BRACKETS -
REMOVAL, SEAT BACK REAR...........23-85
FORM-IN-PLACE GASKETS AND
SEALERS - STANDARD PROCEDURE.....9-232,
9-289,9-360,9-9,9-93
FRAME - INSTALLATION, GRILLE........23-40
FRAME - REAR - INSTALLATION, SEAT
CUSHION...........................23-85
FRAME - REAR - REMOVAL, SEAT
CUSHION...........................23-85
FRAME - REMOVAL, GRILLE............23-40
FRAME DIMENSIONS - SPECIFICATIONS . . 13-17
FRAME H-SECTION REPLACEMENT -
STANDARD PROCEDURE, REAR.........13-15
FRAME RAIL TIP REPLACEMENT -
STANDARD PROCEDURE, LIGHT DUTY
FRONT..............................13-4
FRONT - DESCRIPTION, CRANKSHAFT
OIL SEAL...........................9-254
FRONT - INSTALLATION........5-16,5-17,5-29
FRONT - INSTALLATION...............22-15
FRONT - INSTALLATION, CRANKSHAFT
OIL SEAL........9-134,9-203,9-255,9-324,9-45
FRONT - INSTALLATION, SEAT..........23-82
FRONT - INSTALLATION, SEAT BACK
CUSHION / COVER...................23-83
FRONT - INSTALLATION, SEAT CUSHION
/ COVER............................23-83
FRONT - OPERATION, CRANKSHAFT OIL
SEAL..............................9-254
FRONT - REMOVAL............5-12,5-16,5-28
FRONT - REMOVAL, CRANKSHAFT OIL
SEAL...........9-134,9-203,9-254,9-323,9-44
FRONT - REMOVAL, SEAT..............23-82
FRONT - REMOVAL, SEAT BACK
CUSHION / COVER...................23-83
FRONT - REMOVAL, SEAT CUSHION /
COVER.............................23-83
FRONT AIR DAM - INSTALLATION........13-2
FRONT AIR DAM - REMOVAL............13-2
FRONT AXLE - 9 1/4 AA -
ADJUSTMENTS.......................3-49
FRONT AXLE - 9 1/4 AA - DESCRIPTION . . . 3-45
FRONT AXLE - 9 1/4 AA - DIAGNOSIS
AND TESTING........................3-45
FRONT AXLE - 9 1/4 AA - INSTALLATION . . . 3-48
FRONT AXLE - 9 1/4 AA - OPERATION.....3-45
FRONT AXLE - 9 1/4 AA - REMOVAL......3-48
FRONT AXLE - 9 1/4 AA - SPECIAL
TOOLS..............................3-53
FRONT AXLE - 9 1/4 AA -
SPECIFICATIONS......................3-53
FRONT AXLE - C205F - ADJUSTMENTS....3-21
FRONT AXLE - C205F - DESCRIPTION.....3-18
FRONT AXLE - C205F - DIAGNOSIS AND
TESTING............................3-18
FRONT AXLE - C205F - INSTALLATION.....3-21
FRONT AXLE - C205F - OPERATION.......3-18
FRONT AXLE - C205F - REMOVAL
........3-21
FRONT AXLE - C205F - SPECIAL TOOLS
. . . 3-30
FRONT AXLE - C205F - SPECIFICATIONS
. . . 3-29
FRONT BEARING - INSTALLATION,
OUTPUT SHAFT
...............21-217,21-395
FRONT BEARING - REMOVAL, OUTPUT
SHAFT
......................21-217,21-395FRONT BRAKE HOSE - INSTALLATION......5-9
FRONT BUMPER - INSTALLATION.........13-2
FRONT BUMPER - REMOVAL............13-2
FRONT CENTER SEAT BELT -
INSTALLATION......................8O-27
FRONT CENTER SEAT BELT - REMOVAL . . 8O-26
FRONT CENTER SEAT BELT &
RETRACTOR - INSTALLATION...........8O-26
FRONT CENTER SEAT BELT &
RETRACTOR - REMOVAL..............8O-25
FRONT CLUTCH - ASSEMBLY....21-206,21-386
FRONT CLUTCH - DESCRIPTION . . 21-204,21-384
FRONT CLUTCH - DISASSEMBLY . 21-205,21-384
FRONT CLUTCH - INSPECTION . . . 21-206,21-385
FRONT CLUTCH - OPERATION . . . 21-204,21-384
FRONT CONTROL MODULE -
DESCRIPTION.....................8W-97-4
FRONT CONTROL MODULE -
DESCRIPTION........................8E-5
FRONT CONTROL MODULE - DIAGNOSIS
AND TESTING.....................8W-97-5
FRONT CONTROL MODULE - DIAGNOSIS
AND TESTING........................8E-6
FRONT CONTROL MODULE -
INSTALLATION....................8W-97-5
FRONT CONTROL MODULE -
INSTALLATION........................8E-6
FRONT CONTROL MODULE - OPERATION . 8W-97-5
FRONT CONTROL MODULE - OPERATION . . 8E-5
FRONT CONTROL MODULE - REMOVAL . . 8W-97-5
FRONT CONTROL MODULE - REMOVAL....8E-6
FRONT COVER INSTALLED -
INSTALLATION, FRONT OIL SEAL........9-384
FRONT COVER INSTALLED - REMOVAL,
FRONT OIL SEAL.....................9-384
FRONT COVER REMOVED -
INSTALLATION, FRONT OIL SEAL........9-384
FRONT COVER REMOVED - REMOVAL,
FRONT OIL SEAL.....................9-384
FRONT CROSSMEMBER - INSTALLATION . . 13-23
FRONT CROSSMEMBER - REMOVAL.....13-23
FRONT DOOR GLASS RUN
WEATHERSTRIP - INSTALLATION........23-92
FRONT DOOR GLASS RUN
WEATHERSTRIP - REMOVAL............23-92
FRONT DOOR INNER BELT MOLDING -
INSTALLATION.......................23-93
FRONT DOOR INNER BELT MOLDING -
REMOVAL..........................23-93
FRONT DOOR OUTER BELT MOLDING -
INSTALLATION.......................23-93
FRONT DOOR OUTER BELT MOLDING -
REMOVAL..........................23-93
FRONT FASCIA - INSTALLATION..........13-3
FRONT FASCIA - REMOVAL..............13-3
FRONT FENDER - INSTALLATION........23-39
FRONT FENDER - REMOVAL............23-39
FRONT FOG LAMP RELAY - DIAGNOSIS
AND TESTING.......................8L-12
FRONT FRAME RAIL TIP REPLACEMENT
- STANDARD PROCEDURE, LIGHT
DUTY...............................13-4
FRONT HOSE - REMOVAL
................5-9
FRONT MOUNT - INSTALLATION
. . . 9-144,9-211,
9-265,9-335,9-392,9-58
FRONT MOUNT - REMOVAL
. . 9-144,9-211,9-264,
9-335,9-392,9-57
FRONT OIL SEAL - FRONT COVER
INSTALLED - INSTALLATION
............9-384
FRONT OIL SEAL - FRONT COVER
INSTALLED - REMOVAL
...............9-384
FRONT OIL SEAL - FRONT COVER
REMOVED - INSTALLATION
.............9-384
FRONT OIL SEAL - FRONT COVER
REMOVED - REMOVAL
................9-384
FRONT OUTBOARD SEAT BELT BUCKLE -
INSTALLATION
......................8O-34
FRONT OUTBOARD SEAT BELT BUCKLE -
REMOVAL
..........................8O-33
FRONT OUTPUT SHAFT SEAL -
INSTALLATION
....21-618,21-653,21-683,21-717
FRONT OUTPUT SHAFT SEAL -
REMOVAL
.......21-617,21-653,21-683,21-717
FRONT PARKING BRAKE CABLE -
INSTALLATION
........................5-32
FRONT PARKING BRAKE CABLE -
REMOVAL
...........................5-31FRONT PROPELLER SHAFT -
INSTALLATION.........................3-7
FRONT PROPELLER SHAFT - REMOVAL.....3-6
FRONT SEAL - INSTALLATION, OIL
PUMP............................21-567
FRONT SEAL - REMOVAL, OIL PUMP....21-567
FRONT SERVO - ASSEMBLY.....21-209,21-388
FRONT SERVO - CLEANING.....21-208,21-388
FRONT SERVO - DESCRIPTION . . . 21-207,21-387
FRONT SERVO - DISASSEMBLY . . 21-208,21-388
FRONT SERVO - INSPECTION....21-208,21-388
FRONT SERVO - OPERATION....21-208,21-387
FRONT SKID PLATE - INSTALLATION.....13-24
FRONT SKID PLATE - REMOVAL.........13-24
FRONT SUSPENSION - DESCRIPTION,
GEAR - INDEPENDENT................19-16
FRONT SUSPENSION - INSTALLATION,
GEAR - INDEPENDENT................19-17
FRONT SUSPENSION - REMOVAL, GEAR
- INDEPENDENT.....................19-16
FRONT SUSPENSION, SPECIAL TOOLS....2-11
FRONT TOW HOOK ASSEMBLY -
INSTALLATION.......................13-26
FRONT TOW HOOK ASSEMBLY -
REMOVAL..........................13-26
FRONT WHEEL SPEED SENSOR -
DESCRIPTION........................5-41
FRONT WHEEL SPEED SENSOR -
INSTALLATION........................5-42
FRONT WHEEL SPEED SENSOR -
OPERATION..........................5-41
FRONT WHEEL SPEED SENSOR -
REMOVAL...........................5-41
FRONT WHEELHOUSE SPLASH SHIELD -
INSTALLATION.......................23-41
FRONT WHEELHOUSE SPLASH SHIELD -
REMOVAL..........................23-40
FUEL CONTROL ACTUATOR -
DESCRIPTION.......................14-85
FUEL CONTROL ACTUATOR -
INSTALLATION.......................14-85
FUEL CONTROL ACTUATOR -
OPERATION.........................14-85
FUEL CONTROL ACTUATOR - REMOVAL . . . 14-85
FUEL DELIVERY - GAS - DESCRIPTION....14-1
FUEL DELIVERY - GAS - OPERATION......14-2
FUEL DRAIN CIRCUIT - OPERATION......14-78
FUEL FILL DOOR - INSTALLATION.......23-39
FUEL FILL DOOR - REMOVAL...........23-39
FUEL FILLER CAP - DESCRIPTION.......25-13
FUEL FILLER CAP - OPERATION.........25-13
FUEL FILTER - STANDARD
PROCEDURES, WATER DRAINING AT.....14-57
FUEL FILTER / WATER SEPARATOR -
DESCRIPTION.......................14-61
FUEL FILTER / WATER SEPARATOR -
INSTALLATION.......................14-62
FUEL FILTER / WATER SEPARATOR -
OPERATION.........................14-61
FUEL FILTER / WATER SEPARATOR -
REMOVAL..........................14-61
FUEL FILTER/PRESSURE REGULATOR -
DESCRIPTION........................14-6
FUEL FILTER/PRESSURE REGULATOR -
OPERATION..........................14-6
FUEL GAUGE - DESCRIPTION...........8J-25
FUEL GAUGE - OPERATION.............8J-26
FUEL HEATER - DESCRIPTION..........14-63
FUEL HEATER - DIAGNOSIS AND
TESTING...........................14-63
FUEL HEATER - OPERATION............14-63
FUEL HEATER RELAY - DESCRIPTION....14-64
FUEL HEATER RELAY - INSTALLATION....14-64
FUEL HEATER RELAY - OPERATION......14-64
FUEL HEATER RELAY - REMOVAL........14-64
FUEL INDICATOR - DESCRIPTION, LOW . . . 8J-29
FUEL INDICATOR - OPERATION, LOW.....8J-29
FUEL INJECTION PUMP - DESCRIPTION . . 14-64
FUEL INJECTION PUMP - INSTALLATION . . 14-67
FUEL INJECTION PUMP - OPERATION....14-64
FUEL INJECTION PUMP - REMOVAL......14-65
FUEL INJECTION PUMP TIMING -
DIAGNOSIS AND TESTING.............14-65
FUEL INJECTOR - DESCRIPTION
....14-32,14-85
FUEL INJECTOR - INSTALLATION
........14-87
FUEL INJECTOR - OPERATION
.....14-32,14-86
FUEL INJECTOR - REMOVAL
............14-87
FUEL INJECTOR FIRING ORDER, DIESEL
. . 14-60
14 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

NV4500 - SPECIFICATIONS, MANUAL
TRANSMISSION......................21-79
NV5600 - ASSEMBLY, MANUAL
TRANSMISSION.....................21-105
NV5600 - DESCRIPTION, MANUAL
TRANSMISSION......................21-87
NV5600 - DIAGNOSIS AND TESTING,
MANUAL TRANSMISSION..............21-89
NV5600 - DISASSEMBLY, MANUAL
TRANSMISSION......................21-90
NV5600 - INSPECTION, MANUAL
TRANSMISSION.....................21-104
NV5600 - INSTALLATION, MANUAL
TRANSMISSION.....................21-120
NV5600 - OPERATION, MANUAL
TRANSMISSION......................21-89
NV5600 - REMOVAL, MANUAL
TRANSMISSION......................21-89
NV5600 - SPECIAL TOOLS, MANUAL
TRANSMISSION.....................21-122
NV5600 - SPECIFICATIONS............21-122
ODOMETER - DESCRIPTION............8J-31
ODOMETER - OPERATION..............8J-31
OFF INDICATOR - DESCRIPTION,
OVERDRIVE.........................8J-33
OFF INDICATOR - OPERATION,
OVERDRIVE.........................8J-33
OIL - DESCRIPTION, REFRIGERANT......24-54
OIL - OPERATION, REFRIGERANT........24-54
OIL - STANDARD PROCEDURE, ENGINE . . 9-269,
9-396
OIL AND LUBRICANTS - DESCRIPTION,
ENGINE..............................0-2
OIL COOLER - INSTALLATION, AIR TO.....7-75
OIL COOLER - REMOVAL, AIR TO.........7-74
OIL COOLER - REMOVAL, WATER TO......7-74
OIL FILTER - INSTALLATION . 9-153,9-217,9-270,
9-342,9-397,9-70
OIL FILTER - REMOVAL.....9-152,9-216,9-270,
9-342,9-397,9-69
OIL LEAK - DIAGNOSIS AND TESTING,
ENGINE...................9-150,9-214,9-63
OIL LEAKS - DIAGNOSIS AND TESTING,
ENGINE.......................9-269,9-394
OIL LEVEL - STANDARD PROCEDURE,
ENGINE............................9-341
OIL LEVEL - STANDARD PROCEDURE,
REFRIGERANT.......................24-54
OIL PAN - CLEANING . . . 9-270,9-342,9-397,9-65
OIL PAN - DESCRIPTION................9-65
OIL PAN - INSPECTION . . 9-271,9-342,9-397,9-66
OIL PAN - INSTALLATION . . . 9-153,9-217,9-271,
9-342,9-398,9-66
OIL PAN - REMOVAL . . 9-153,9-217,9-270,9-342,
9-397,9-65
OIL PRESSURE - DIAGNOSIS AND
TESTING, CHECKING ENGINE . . 9-150,9-214,9-64
OIL PRESSURE - DIAGNOSIS AND
TESTING, ENGINE..........9-269,9-338,9-396
OIL PRESSURE GAUGE - DESCRIPTION . . . 8J-32
OIL PRESSURE GAUGE - OPERATION.....8J-32
OIL PRESSURE RELIEF VALVE -
CLEANING..........................9-343
OIL PRESSURE RELIEF VALVE -
INSPECTION........................9-343
OIL PRESSURE RELIEF VALVE -
INSTALLATION.......................9-343
OIL PRESSURE RELIEF VALVE -
REMOVAL..........................9-343
OIL PRESSURE SENSOR/SWITCH -
DESCRIPTION........................9-66
OIL PRESSURE SENSOR/SWITCH -
INSTALLATION...................9-343,9-67
OIL PRESSURE SENSOR/SWITCH -
OPERATION..........................9-66
OIL PRESSURE SENSOR/SWITCH -
REMOVAL......................9-343,9-67
OIL PUMP - ASSEMBLY......9-156,9-274,9-68
OIL PUMP - ASSEMBLY . . 21-215,21-393,21-566
OIL PUMP - CLEANING . 9-155,9-218,9-344,9-398
OIL PUMP - CLEANING
. . . 21-214,21-393,21-566
OIL PUMP - DESCRIPTION
......21-212,21-392,
21-562
OIL PUMP - DISASSEMBLY
. . . 9-155,9-272,9-67
OIL PUMP - DISASSEMBLY
.....21-212,21-393,
21-564
OIL PUMP - INSPECTION
....9-155,9-218,9-272,
9-344,9-399,9-67OIL PUMP - INSPECTION . 21-214,21-393,21-566
OIL PUMP - INSTALLATION . . 9-157,9-219,9-274,
9-344,9-400,9-68
OIL PUMP - OPERATION . . 21-212,21-392,21-562
OIL PUMP - REMOVAL......9-154,9-218,9-272,
9-343,9-398,9-67
OIL PUMP FRONT SEAL - INSTALLATION . 21-567
OIL PUMP FRONT SEAL - REMOVAL....21-567
OIL PUMP VOLUME CHECK - STANDARD
PROCEDURE.......................21-563
OIL SEAL - FRONT - DESCRIPTION,
CRANKSHAFT.......................9-254
OIL SEAL - FRONT - INSTALLATION,
CRANKSHAFT....9-134,9-203,9-255,9-324,9-45
OIL SEAL - FRONT - OPERATION,
CRANKSHAFT.......................9-254
OIL SEAL - FRONT - REMOVAL,
CRANKSHAFT....9-134,9-203,9-254,9-323,9-44
OIL SEAL - FRONT COVER INSTALLED -
INSTALLATION, FRONT................9-384
OIL SEAL - FRONT COVER INSTALLED -
REMOVAL, FRONT....................9-384
OIL SEAL - FRONT COVER REMOVED -
INSTALLATION, FRONT................9-384
OIL SEAL - FRONT COVER REMOVED -
REMOVAL, FRONT....................9-384
OIL SEAL - REAR - DESCRIPTION,
CRANKSHAFT.......................9-255
OIL SEAL - REAR - INSTALLATION,
CRANKSHAFT . . . 9-136,9-204,9-256,9-325,9-385,
9-46
OIL SEAL - REAR - OPERATION,
CRANKSHAFT.........................9-255
OIL SEAL - REAR - REMOVAL,
CRANKSHAFT . . . 9-135,9-204,9-255,9-325,9-385,
9-45
OIL SEAL RETAINER - INSTALLATION,
CRANKSHAFT REAR........9-205,9-326,9-386
OIL SEAL RETAINER - REMOVAL,
CRANKSHAFT REAR........9-204,9-326,9-386
OIL SERVICE - STANDARD PROCEDURE,
ENGINE..............9-151,9-215,9-341,9-70
ON-BOARD DIAGNOSTICS (OBD) -
DIAGNOSIS AND TESTING...............7-5
ONLY - ASSEMBLY, 5.9L................7-73
ONLY - DISASSEMBLY, 5.9L.............7-73
ON/OFF RELAY - DESCRIPTION, WIPER . . . 8R-25
ON/OFF RELAY - DIAGNOSIS AND
TESTING, WIPER.....................8R-26
ON/OFF RELAY - INSTALLATION, WIPER . . 8R-26
ON/OFF RELAY - OPERATION, WIPER....8R-25
ON/OFF RELAY - REMOVAL, WIPER......8R-26
ON/OFF SWITCH - DESCRIPTION,
PASSENGER AIRBAG.................8O-38
ON/OFF SWITCH - INSTALLATION,
PASSENGER AIRBAG.................8O-39
ON/OFF SWITCH - OPERATION,
PASSENGER AIRBAG.................8O-38
ON/OFF SWITCH - REMOVAL,
PASSENGER AIRBAG.................8O-39
OPEN-CIRCUIT VOLTAGE TEST -
STANDARD PROCEDURE...............8F-10
OPENING COVER - INSTALLATION,
STEERING COLUMN..................23-61
OPENING COVER - REMOVAL, STEERING
COLUMN...........................23-61
OPENING DIMENSIONS -
SPECIFICATIONS, BODY
...............23-99
OPENING SEAL - INSTALLATION, DOOR
. . . 23-92
OPENING SEAL - REMOVAL, DOOR
......23-92
OPENING SUPPORT BRACKET -
INSTALLATION, STEERING COLUMN
......23-62
OPENING SUPPORT BRACKET -
REMOVAL, STEERING COLUMN
.........23-61
OPERATING MODES, STANDARD
PROCEDURE - CONFIGURING A NEW
MODULE / SWITCH
....................8Q-3
ORDER / CABLE ROUTING, 5.7L V-8
ENGINE - FIRING
......................8I-4
ORDER, 3.7L V-6 - ENGINE FIRING
........8I-4
ORDER, 4.7L V-8 - ENGINE FIRING
........8I-4
ORDER, 5.9L V-8 - ENGINE FIRING
........8I-4
ORDER, 8.0L V-10 ENGINE - SPARK
PLUG CABLE
.........................8I-5
ORDER, DIESEL - FUEL INJECTOR
FIRING
.............................14-60
ORIFICE TUBE - DESCRIPTION, A/C
......24-48ORIFICE TUBE - DIAGNOSIS AND
TESTING, FIXED.....................24-48
ORIFICE TUBE - INSTALLATION, A/C......24-49
ORIFICE TUBE - OPERATION, A/C........24-48
ORIFICE TUBE - REMOVAL, A/C.........24-49
OUT INDICATOR - DESCRIPTION, LAMP . . . 8J-28
OUT INDICATOR - OPERATION, LAMP....8J-28
OUTBOARD - INSTALLATION, CENTER &
LEFT..............................8O-45
OUTBOARD - INSTALLATION, CENTER
ANCHOR & RIGHT...................8O-45
OUTBOARD - REMOVAL, CENTER & LEFT . 8O-43
OUTBOARD - REMOVAL, CENTER
ANCHOR & RIGHT...................8O-43
OUTBOARD SEAT BELT & RETRACTOR -
INSTALLATION, REAR.................8O-42
OUTBOARD SEAT BELT & RETRACTOR -
REMOVAL, REAR....................8O-41
OUTBOARD SEAT BELT BUCKLE -
INSTALLATION, FRONT................8O-34
OUTBOARD SEAT BELT BUCKLE -
REMOVAL, FRONT....................8O-33
OUTER BELT MOLDING - INSTALLATION,
FRONT DOOR.......................23-93
OUTER BELT MOLDING - INSTALLATION,
REAR DOOR........................23-94
OUTER BELT MOLDING - REMOVAL,
FRONT DOOR.......................23-93
OUTER BELT MOLDING - REMOVAL,
REAR DOOR........................23-94
OUTER TIE ROD END - DIAGNOSIS AND
TESTING.............................19-31
OUTER TIE ROD END - INSTALLATION....19-32
OUTER TIE ROD END - REMOVAL.......19-31
OUTLET - DESCRIPTION, CIGAR
LIGHTER.........................8W-97-2
OUTLET - DESCRIPTION, POWER......8W-97-7
OUTLET - DIAGNOSIS AND TESTING,
CIGAR LIGHTER...................8W-97-2
OUTLET - DIAGNOSIS AND TESTING,
POWER..........................8W-97-7
OUTLET - INSTALLATION, POWER.....8W-97-7
OUTLET - OPERATION, CIGAR LIGHTER . 8W-97-2
OUTLET - OPERATION, POWER.......8W-97-7
OUTLET - REMOVAL, POWER.........8W-97-7
OUTLETS - INSTALLATION, PANEL.......24-24
OUTLETS - REMOVAL, PANEL...........24-24
OUTPUT - DESCRIPTION, PCM...........8I-6
OUTPUT - OPERATION, PCM............14-32
OUTPUT - OPERATION, PCM.............8I-6
OUTPUT SHAFT FRONT BEARING -
INSTALLATION................21-217,21-395
OUTPUT SHAFT FRONT BEARING -
REMOVAL...................21-217,21-395
OUTPUT SHAFT REAR BEARING -
INSTALLATION................21-217,21-396
OUTPUT SHAFT REAR BEARING -
REMOVAL...................21-217,21-395
OUTPUT SHAFT SEAL - INSTALLATION,
FRONT..........21-618,21-653,21-683,21-717
OUTPUT SHAFT SEAL - REMOVAL,
FRONT..........21-617,21-653,21-683,21-717
OUTPUT SPEED SENSOR - DESCRIPTION . 21-567
OUTPUT SPEED SENSOR -
INSTALLATION......................21-567
OUTPUT SPEED SENSOR - OPERATION
. . 21-567
OUTPUT SPEED SENSOR - REMOVAL
. . . 21-567
OVERDRIVE CLUTCH - DESCRIPTION
. . . 21-218,
21-396
OVERDRIVE CLUTCH - OPERATION
.....21-218,
21-396
OVERDRIVE ELECTRICAL CONTROLS -
DIAGNOSIS AND TESTING
......21-219,21-397
OVERDRIVE OFF INDICATOR -
DESCRIPTION
.......................8J-33
OVERDRIVE OFF INDICATOR -
OPERATION
.........................8J-33
OVERDRIVE SWITCH - DESCRIPTION
. . . 21-218,
21-397,21-568
OVERDRIVE SWITCH - INSTALLATION
. . . 21-219,
21-397,21-569
OVERDRIVE SWITCH - OPERATION
.....21-218,
21-397,21-568
OVERDRIVE SWITCH - REMOVAL
......21-219,
21-397,21-568
OVERDRIVE UNIT - ASSEMBLY
. . . 21-228,21-406
OVERDRIVE UNIT - CLEANING
. . . 21-227,21-405
DRINDEX 23
Description Group-Page Description Group-Page Description Group-Page

PLANETARY GEARTRAIN/OUTPUT SHAFT
- INSPECTION................21-245,21-422
PLANETARY GEARTRAIN/OUTPUT SHAFT
- OPERATION.................21-243,21-420
PLASTIC BODY PANEL REPAIR -
STANDARD PROCEDURE................23-3
PLATE - DESCRIPTION, BODY CODE....Intro.-4
PLATE - DESCRIPTION, ENGINE DATA....9-297
PLATE - INSTALLATION, FLEX . . 9-137,9-205,9-47
PLATE - INSTALLATION, FRONT SKID.....13-24
PLATE - INSTALLATION, SUPPORT........5-29
PLATE - INSTALLATION, TRANSFER
CASE SKID.........................13-26
PLATE - REMOVAL, FLEX.....9-137,9-205,9-47
PLATE - REMOVAL, FRONT SKID........13-24
PLATE - REMOVAL, SUPPORT...........5-29
PLATE - REMOVAL, TRANSFER CASE
SKID..............................13-26
PLATE LAMP - INSTALLATION, LICENSE . . 8L-16
PLATE LAMP - REMOVAL, LICENSE......8L-16
PLATE LAMP UNIT - INSTALLATION,
LICENSE...........................8L-16
PLATE LAMP UNIT - REMOVAL, LICENSE . . 8L-16
PLATES - INSTALLATION, EXTERIOR
NAME.............................23-38
PLATES - REMOVAL, EXTERIOR NAME....23-38
PLUG - DESCRIPTION, SPARK...........8I-27
PLUG - INSTALLATION, CAMSHAFT
CORE HOLE.........................9-201
PLUG - REMOVAL, CAMSHAFT CORE
HOLE..............................9-200
PLUG - REMOVAL, SPARK..............8I-30
PLUG CABLE - DESCRIPTION, SPARK.....8I-33
PLUG CABLE - INSTALLATION, SPARK....8I-35
PLUG CABLE - OPERATION, SPARK.......8I-33
PLUG CABLE - REMOVAL, SPARK........8I-34
PLUG CABLE ORDER, 8.0L V-10 ENGINE
- SPARK .............................8I-5
PLUG CABLE RESISTANCE,
SPECIFICATIONS - SPARK...............8I-5
PLUG CABLES - DIAGNOSIS AND
TESTING, SPARK.....................8I-33
PLUG CONDITIONS - DIAGNOSIS AND
TESTING, SPARK.....................8I-27
PLUGS - INSTALLATION, CORE..........9-130
PLUGS - REMOVAL, CORE.............9-129
PLUGS, SPECIFICATIONS - SPARK........8I-5
PLUMBING - CLEANING, CHARGE AIR
COOLER............................11-16
PLUMBING - DESCRIPTION, CHARGE
AIR COOLER........................11-15
PLUMBING - INSPECTION, CHARGE AIR
COOLER............................11-16
PLUMBING - INSTALLATION, CHARGE
AIR COOLER........................11-16
PLUMBING - OPERATION, CHARGE AIR
COOLER............................11-15
PLUMBING - REMOVAL, CHARGE AIR
COOLER............................11-15
PLY TIRES - DESCRIPTION, RADIAL.......22-6
POLISHING - DESCRIPTION, FINESSE
SANDING/BUFFING...................23-75
PORT - DESCRIPTION, REFRIGERANT
SYSTEM SERVICE.....................24-1
PORT - OPERATION, REFRIGERANT
SYSTEM SERVICE.....................24-2
POSITION SENSOR - DESCRIPTION.....21-618,
21-654
POSITION SENSOR - DESCRIPTION,
ACCELERATOR PEDAL.................14-25
POSITION SENSOR - DESCRIPTION,
CAMSHAFT.........................14-82
POSITION SENSOR - DESCRIPTION,
CAMSHAFT...........................8I-8
POSITION SENSOR - DESCRIPTION,
CRANKSHAFT..................14-26,14-83
POSITION SENSOR - DESCRIPTION,
THROTTLE..........................14-52
POSITION SENSOR - INSTALLATION
....21-619,
21-654
POSITION SENSOR - INSTALLATION,
ACCELERATOR PEDAL
.................14-25
POSITION SENSOR - INSTALLATION,
CAMSHAFT
.........................14-83
POSITION SENSOR - INSTALLATION,
CAMSHAFT
..........................8I-14
POSITION SENSOR - INSTALLATION,
CRANKSHAFT
..................14-30,14-84POSITION SENSOR - INSTALLATION,
THROTTLE..........................14-54
POSITION SENSOR - OPERATION . 21-619,21-654
POSITION SENSOR - OPERATION,
ACCELERATOR PEDAL.................14-25
POSITION SENSOR - OPERATION,
CAMSHAFT.........................14-82
POSITION SENSOR - OPERATION,
CAMSHAFT...........................8I-8
POSITION SENSOR - OPERATION,
CRANKSHAFT..................14-26,14-83
POSITION SENSOR - OPERATION,
THROTTLE..........................14-52
POSITION SENSOR - REMOVAL . . 21-619,21-654
POSITION SENSOR - REMOVAL,
ACCELERATOR PEDAL.................14-25
POSITION SENSOR - REMOVAL,
CAMSHAFT.........................14-83
POSITION SENSOR - REMOVAL,
CAMSHAFT..........................8I-11
POSITION SENSOR - REMOVAL,
CRANKSHAFT..................14-29,14-84
POSITION SENSOR - REMOVAL,
THROTTLE..........................14-53
POSITION SWITCH - DESCRIPTION,
CLUTCH PEDAL.......................6-14
POSITION SWITCH - DIAGNOSIS AND
TESTING, CLUTCH PEDAL...............6-14
POSITION SWITCH - OPERATION,
CLUTCH PEDAL.......................6-14
POTENTIAL - STANDARD PROCEDURE,
TESTING OF VOLTAGE..............8W-01-9
POWER - INSTALLATION, WINDOW
REGULATOR...................23-25,23-34
POWER - REMOVAL, WINDOW
REGULATOR...................23-25,23-34
POWER BRAKE BOOSTER -
DESCRIPTION........................5-25
POWER BRAKE BOOSTER -
INSTALLATION........................5-25
POWER BRAKE BOOSTER - OPERATION . . . 5-25
POWER BRAKE BOOSTER - REMOVAL.....5-25
POWER DISTRIBUTION - DESCRIPTION . 8W-97-1
POWER DISTRIBUTION - OPERATION . . 8W-97-1
POWER DISTRIBUTION SYSTEMS,
SPECIAL TOOLS...................8W-97-2
POWER GROUNDS - DESCRIPTION......8E-10
POWER LOCK SWITCH - DIAGNOSIS
AND TESTING........................8N-4
POWER LOCK SWITCH - INSTALLATION . . . 8N-4
POWER LOCK SWITCH - REMOVAL.......8N-4
POWER LOCKS - DESCRIPTION..........8N-1
POWER LOCKS - DIAGNOSIS AND
TESTING............................8N-3
POWER LOCKS - OPERATION............8N-2
POWER MIRROR SWITCH - DIAGNOSIS
AND TESTING.......................8N-13
POWER MIRROR SWITCH - REMOVAL
. . . 8N-13
POWER MIRRORS - DESCRIPTION
......8N-11
POWER MIRRORS - DIAGNOSIS AND
TESTING
...........................8N-11
POWER MIRRORS - OPERATION
........8N-11
POWER MODULE - DESCRIPTION,
INTEGRATED
......................8W-97-3
POWER MODULE - INSTALLATION,
INTEGRATED
......................8W-97-4
POWER MODULE - OPERATION,
INTEGRATED
......................8W-97-3
POWER MODULE - REMOVAL,
INTEGRATED
......................8W-97-3
POWER OUTLET - DESCRIPTION
......8W-97-7
POWER OUTLET - DIAGNOSIS AND
TESTING
.........................8W-97-7
POWER OUTLET - INSTALLATION
.....8W-97-7
POWER OUTLET - OPERATION
........8W-97-7
POWER OUTLET - REMOVAL
.........8W-97-7
POWER SEAT SYSTEM - DIAGNOSIS
AND TESTING
.......................8N-14
POWER SEAT TRACK - DESCRIPTION
....8N-18
POWER SEAT TRACK - DIAGNOSIS AND
TESTING
...........................8N-18
POWER SEAT TRACK - INSTALLATION
....8N-19
POWER SEAT TRACK - OPERATION
......8N-18
POWER SEAT TRACK - REMOVAL
.......8N-19
POWER SEATS - DESCRIPTION
.........8N-14
POWER SEATS - OPERATION
...........8N-14POWER STEERING FLOW AND
PRESSURE - DIAGNOSIS AND
TESTING............................19-4
POWER STEERING FLUID -
DESCRIPTION.........................0-3
POWER STEERING FLUID LEVEL
CHECKING - STANDARD PROCEDURE....19-42
POWER STEERING GEAR, SPECIAL
TOOLS.............................19-22
POWER STEERING GEAR,
SPECIFICATIONS.....................19-21
POWER STEERING PRESSURE SWITCH -
DESCRIPTION.......................19-45
POWER STEERING PRESSURE SWITCH -
OPERATION.........................19-45
POWER STEERING PUMP - INITIAL
OPERATION - STANDARD PROCEDURE . . . 19-39
POWER STEERING SYSTEM -
DIAGNOSIS AND TESTING..............19-2
POWER STEERING SYSTEM -
STANDARD PROCEDURE, FLUSHING.....19-39
POWER WINDOWS - DESCRIPTION......8N-21
POWER WINDOWS - DIAGNOSIS AND
TESTING...........................8N-21
POWER WINDOWS - OPERATION........8N-21
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON FUSES . 8W-01-10
PRE-ALIGNMENT INSPECTION -
DIAGNOSIS AND TESTING...............2-2
PRECAUTIONS - CAUTION,
REFRIGERANT HOSES/LINES/TUBES......24-33
PRECAUTIONS AND WARNINGS,
WARNING - SAFETY.....................23-1
PRECAUTIONS, STANDARD PROCEDURE
- SAFETY............................8L-7
PRECAUTIONS, WARNING -
WINDSHIELD SAFETY.................23-88
PREFERENCES - STANDARD
PROCEDURE, RKE TRANSMITTER
CUSTOMER..........................8N-9
PRELIMINARY - DIAGNOSIS AND
TESTING..............21-139,21-320,21-491
PRELIMINARY CHECKS - DIAGNOSIS
AND TESTING........................7-10
PREPARATION - STANDARD
PROCEDURE, ENGINE GASKET
SURFACE............................9-10
PRESSURE - DIAGNOSIS AND TESTING,
CHECKING ENGINE OIL.......9-150,9-214,9-64
PRESSURE - DIAGNOSIS AND TESTING,
CYLINDER COMPRESSION . . . 9-182,9-231,9-359,
9-8,9-92
PRESSURE - DIAGNOSIS AND TESTING,
ENGINE OIL...............9-269,9-338,9-396
PRESSURE - DIAGNOSIS AND TESTING,
POWER STEERING FLOW...............19-4
PRESSURE - DIAGNOSIS AND TESTING,
TURBOCHARGER BOOST...............11-10
PRESSURE BLEEDING - STANDARD
PROCEDURE..........................5-5
PRESSURE CAP - DESCRIPTION,
RADIATOR...........................7-60
PRESSURE CAP - OPERATION,
RADIATOR...........................7-61
PRESSURE, DIESEL - FUEL SYSTEM
.....14-60
PRESSURE FOR HIGH SPEEDS -
DESCRIPTION, TIRE
...................22-6
PRESSURE GAUGE - DESCRIPTION, OIL
. . 8J-32
PRESSURE GAUGE - OPERATION, OIL
....8J-32
PRESSURE GAUGES - DIAGNOSIS AND
TESTING
............................22-7
PRESSURE HOSE - INSTALLATION
. . 19-43,19-44
PRESSURE HOSE - REMOVAL
.....19-43,19-44
PRESSURE LEAKAGE - DIAGNOSIS AND
TESTING, CYLINDER COMBUSTION
. 9-182,9-231,
9-359,9-8,9-92
PRESSURE LIMITING VALVE -
DESCRIPTION, FUEL
..................14-72
PRESSURE LIMITING VALVE -
INSTALLATION, FUEL
.................14-73
PRESSURE LIMITING VALVE -
OPERATION, FUEL
....................14-72
PRESSURE LIMITING VALVE - REMOVAL,
FUEL
..............................14-72
PRESSURE (LP) SENSOR -
DESCRIPTION, LINE
.................21-559
DRINDEX 25
Description Group-Page Description Group-Page Description Group-Page

RAIL WEATHERSTRIP RETAINER -
REMOVAL, DRIP.....................23-92
RANGE SENSOR - DESCRIPTION,
TRANSMISSION.........21-263,21-441,21-581
RANGE SENSOR - INSTALLATION,
TRANSMISSION...............21-266,21-444
RANGE SENSOR - OPERATION,
TRANSMISSION.........21-263,21-441,21-581
RANGE SENSOR - REMOVAL,
TRANSMISSION...............21-265,21-443
RANGE SENSOR (TRS) - DIAGNOSIS
AND TESTING, TRANSMISSION . . 21-264,21-442
RATINGS, SPECIFICATIONS -
GENERATOR........................8F-20
RATTLE - STANDARD PROCEDURE,
BUZZ, SQUEAK......................23-11
RE TRANSMISSION, SPECIAL TOOLS . . . 21-189,
21-370
READING LAMP - DESCRIPTION.........8L-26
READING LAMP - INSTALLATION........8L-26
READING LAMP - OPERATION..........8L-26
READING LAMP - REMOVAL............8L-26
READING/COURTESY LAMP
REPLACEMENT - STANDARD
PROCEDURE.........................8M-3
REAR - DESCRIPTION..................2-38
REAR - DESCRIPTION, CRANKSHAFT OIL
SEAL..............................9-255
REAR - FOOTMANS LOOP BRACKETS -
INSTALLATION, SEAT BACK............23-85
REAR - FOOTMANS LOOP BRACKETS -
REMOVAL, SEAT BACK................23-85
REAR - INSTALLATION.........5-16,5-17,5-28
REAR - INSTALLATION................22-14
REAR - INSTALLATION, CRANKSHAFT
OIL SEAL . . . 9-136,9-204,9-256,9-325,9-385,9-46
REAR - INSTALLATION, SEAT...........23-84
REAR - INSTALLATION, SEAT BACK......23-84
REAR - INSTALLATION, SEAT BACK
CUSHION / COVER...................23-85
REAR - INSTALLATION, SEAT CUSHION /
COVER.............................23-85
REAR - INSTALLATION, SEAT CUSHION
FRAME.............................23-85
REAR - OPERATION, CRANKSHAFT OIL
SEAL..............................9-255
REAR - REMOVAL.........5-12,5-16,5-17,5-28
REAR - REMOVAL, CRANKSHAFT OIL
SEAL......9-135,9-204,9-255,9-325,9-385,9-45
REAR - REMOVAL, SEAT...............23-84
REAR - REMOVAL, SEAT BACK..........23-84
REAR - REMOVAL, SEAT BACK CUSHION
/ COVER............................23-85
REAR - REMOVAL, SEAT CUSHION /
COVER.............................23-85
REAR - REMOVAL, SEAT CUSHION
FRAME.............................23-85
REAR AXLE - 10 1/2 AA -
ADJUSTMENTS......................3-104
REAR AXLE - 10 1/2 AA - DESCRIPTION . . 3-100
REAR AXLE - 10 1/2 AA - DIAGNOSIS
AND TESTING.......................3-100
REAR AXLE - 10 1/2 AA - INSTALLATION . . 3-103
REAR AXLE - 10 1/2 AA - OPERATION....3-100
REAR AXLE - 10 1/2 AA - REMOVAL.....3-103
REAR AXLE - 10 1/2 AA - SPECIAL
TOOLS.............................3-108
REAR AXLE - 10 1/2 AA -
SPECIFICATIONS.....................3-108
REAR AXLE - 11 1/2 AA -
ADJUSTMENTS......................3-131
REAR AXLE - 11 1/2 AA - DESCRIPTION . . 3-127
REAR AXLE - 11 1/2 AA - DIAGNOSIS
AND TESTING.......................3-127
REAR AXLE - 11 1/2 AA - INSTALLATION . . 3-130
REAR AXLE - 11 1/2 AA - OPERATION....3-127
REAR AXLE - 11 1/2 AA - REMOVAL.....3-130
REAR AXLE - 11 1/2 AA - SPECIAL
TOOLS.............................3-135
REAR AXLE - 11 1/2 AA -
SPECIFICATIONS.....................3-135
REAR AXLE - 9 1/4 - ADJUSTMENTS......3-74
REAR AXLE - 9 1/4 - DESCRIPTION
.......3-69
REAR AXLE - 9 1/4 - DIAGNOSIS AND
TESTING
............................3-69
REAR AXLE - 9 1/4 - INSTALLATION
......3-74
REAR AXLE - 9 1/4 - OPERATION
.........3-69
REAR AXLE - 9 1/4 - REMOVAL
..........3-74REAR AXLE - 9 1/4 - SPECIAL TOOLS.....3-80
REAR AXLE - 9 1/4 - SPECIFICATIONS.....3-79
REAR BEARING - INSTALLATION,
OUTPUT SHAFT...............21-217,21-396
REAR BEARING - REMOVAL, OUTPUT
SHAFT......................21-217,21-395
REAR BRAKE HOSE - INSTALLATION.......5-9
REAR BRAKE HOSE - REMOVAL...........5-8
REAR BUMPER - INSTALLATION..........13-4
REAR BUMPER - REMOVAL.............13-4
REAR CAB BACK PANEL TRIM -
INSTALLATION.......................23-70
REAR CAB BACK PANEL TRIM -
REMOVAL..........................23-70
REAR CABLE - INSTALLATION, LEFT......5-33
REAR CABLE - INSTALLATION, RIGHT.....5-32
REAR CABLE - REMOVAL, LEFT..........5-32
REAR CABLE - REMOVAL, RIGHT.........5-31
REAR CENTER SEAT BELT &
RETRACTOR - INSTALLATION...........8O-40
REAR CENTER SEAT BELT &
RETRACTOR - REMOVAL..............8O-39
REAR CLUTCH - ASSEMBLY.....21-250,21-428
REAR CLUTCH - CLEANING.....21-250,21-428
REAR CLUTCH - DESCRIPTION . . . 21-248,21-426
REAR CLUTCH - DISASSEMBLY . . 21-249,21-427
REAR CLUTCH - INSPECTION....21-250,21-428
REAR CLUTCH - OPERATION....21-249,21-427
REAR DOOR GLASS RUN
WEATHERSTRIP - INSTALLATION........23-93
REAR DOOR GLASS RUN
WEATHERSTRIP - REMOVAL............23-93
REAR DOOR INNER BELT MOLDING -
INSTALLATION.......................23-94
REAR DOOR INNER BELT MOLDING -
REMOVAL..........................23-94
REAR DOOR OUTER BELT MOLDING -
INSTALLATION.......................23-94
REAR DOOR OUTER BELT MOLDING -
REMOVAL..........................23-94
REAR DOOR SILL TRIM COVER -
INSTALLATION.......................23-72
REAR DOOR SILL TRIM COVER -
REMOVAL..........................23-72
REAR DRUM IN HAT BRAKE - CLEANING . . . 5-33
REAR DRUM IN HAT BRAKE -
INSPECTION.........................5-33
REAR FENDER - INSTALLATION.........23-44
REAR FENDER - REMOVAL.............23-44
REAR FRAME H-SECTION REPLACEMENT
- STANDARD PROCEDURE.............13-15
REAR MOUNT - INSTALLATION....9-147,9-213,
9-267,9-337,9-393,9-60
REAR MOUNT - REMOVAL . . . 9-147,9-213,9-266,
9-337,9-393,9-60
REAR OIL SEAL RETAINER -
INSTALLATION, CRANKSHAFT . 9-205,9-326,9-386
REAR OIL SEAL RETAINER - REMOVAL,
CRANKSHAFT.............9-204,9-326,9-386
REAR OUTBOARD SEAT BELT &
RETRACTOR - INSTALLATION...........8O-42
REAR OUTBOARD SEAT BELT &
RETRACTOR - REMOVAL..............8O-41
REAR PARK BRAKE CABLE -
INSTALLATION........................5-32
REAR PARK BRAKE CABLE - REMOVAL....5-31
REAR PROPELLER SHAFT -
INSTALLATION.........................3-8
REAR PROPELLER SHAFT - REMOVAL
......3-7
REAR SEAL AREA LEAKS - DIAGNOSIS
AND TESTING
..............9-135,9-204,9-64
REAR SERVO - ASSEMBLY
......21-253,21-430
REAR SERVO - CLEANING
......21-252,21-430
REAR SERVO - DESCRIPTION
....21-252,21-429
REAR SERVO - DISASSEMBLY
. . . 21-252,21-430
REAR SERVO - OPERATION
.....21-252,21-429
REAR TUBE / HOSE ASSEMBLY -
INSTALLATION
.........................5-9
REAR TUBE / HOSE ASSEMBLY -
REMOVAL
............................5-8
REAR VIEW MIRROR - REMOVAL
........23-71
REAR WHEEL ANTILOCK - DIAGNOSIS
AND TESTING
........................5-42
REAR WHEEL INSTALLATION -
STANDARD PROCEDURE, DUAL
.........22-12
REAR WHEEL SPEED SENSOR -
DIAGNOSIS AND TESTING
..............5-43REAR WHEEL SPEED SENSOR -
INSTALLATION........................5-43
REAR WHEEL SPEED SENSOR -
REMOVAL...........................5-42
REAR WHEELHOUSE SPLASH SHIELD -
INSTALLATION.......................23-41
REAR WHEELHOUSE SPLASH SHIELD -
REMOVAL..........................23-41
REARVIEW MIRROR SUPPORT BRACKET
- INSTALLATION.....................23-71
RECEIVER - INSTALLATION, ASH........23-52
RECEIVER - REMOVAL, ASH............23-51
RECIRC DOOR - INSTALLATION.........24-30
RECIRC DOOR - REMOVAL.............24-30
RECIRCULATION DOOR ACTUATOR -
DESCRIPTION.......................24-22
RECIRCULATION DOOR ACTUATOR -
INSTALLATION.......................24-23
RECIRCULATION DOOR ACTUATOR -
OPERATION.........................24-22
RECIRCULATION DOOR ACTUATOR -
REMOVAL..........................24-22
RECOVERY - STANDARD PROCEDURE,
REFRIGERANT..................24-34,24-52
RECOVERY CONTAINER-5.9L -
DESCRIPTION, COOLANT...............7-38
RECOVERY CONTAINER-5.9L -
INSTALLATION, COOLANT...............7-38
RECOVERY CONTAINER-5.9L -
OPERATION, COOLANT.................7-38
RECOVERY CONTAINER-5.9L -
REMOVAL, COOLANT..................7-38
REDUCER - DESCRIPTION, SEAT BELT
TENSION...........................8O-48
REDUCER - DIAGNOSIS AND TESTING,
SEAT BELT TENSION..................8O-49
REDUCER - OPERATION, SEAT BELT
TENSION...........................8O-49
REFACING - STANDARD PROCEDURE . 9-197,9-27
REFACING - STANDARD PROCEDURE,
CYLINDER BLOCK....................9-312
REFERENCES - DESCRIPTION, TORQUE . Intro.-11
REFILL - STANDARD PROCEDURE, FLUID
DRAIN..........21-617,21-652,21-682,21-716
REFILLING COOLING SYSTEM
3.7L/4.7L/5.7L ENGINE - STANDARD
PROCEDURE.........................7-18
REFILLING COOLING SYSTEM 5.9L
DIESEL ENGINE - STANDARD
PROCEDURE.........................7-19
REFILLING COOLING SYSTEM 5.9L/8.0L
ENGINE - STANDARD PROCEDURE........7-18
REFRIGERANT - DESCRIPTION..........24-50
REFRIGERANT - OPERATION............24-50
REFRIGERANT HOSES/LINES/TUBES
PRECAUTIONS - CAUTION.............24-33
REFRIGERANT LINE - DESCRIPTION......24-32
REFRIGERANT LINE COUPLER -
DESCRIPTION.......................24-52
REFRIGERANT LINE COUPLER -
INSTALLATION.......................24-53
REFRIGERANT LINE COUPLER -
OPERATION.........................24-52
REFRIGERANT LINE COUPLER -
REMOVAL..........................24-52
REFRIGERANT LINES - OPERATION
......24-32
REFRIGERANT OIL - DESCRIPTION
......24-54
REFRIGERANT OIL - OPERATION
........24-54
REFRIGERANT OIL LEVEL - STANDARD
PROCEDURE
........................24-54
REFRIGERANT RECOVERY - STANDARD
PROCEDURE
...................24-34,24-52
REFRIGERANT SYSTEM CHARGE -
STANDARD PROCEDURE
..........24-35,24-52
REFRIGERANT SYSTEM EVACUATE -
STANDARD PROCEDURE
..........24-35,24-51
REFRIGERANT SYSTEM LEAKS -
DIAGNOSIS AND TESTING
.............24-51
REFRIGERANT SYSTEM SERVICE
EQUIPMENT - STANDARD PROCEDURE
. . . 24-34
REFRIGERANT SYSTEM SERVICE PORT -
DESCRIPTION
........................24-1
REFRIGERANT SYSTEM SERVICE PORT -
OPERATION
..........................24-2
REGULATOR - DESCRIPTION, FUEL
FILTER/PRESSURE
.....................14-6
REGULATOR - DESCRIPTION, VOLTAGE
. . . 8F-27
DRINDEX 27
Description Group-Page Description Group-Page Description Group-Page

SEAT BELT & RETRACTOR - REMOVAL,
REAR OUTBOARD....................8O-41
SEAT BELT BUCKLE - INSTALLATION,
FRONT OUTBOARD...................8O-34
SEAT BELT BUCKLE - REMOVAL, FRONT
OUTBOARD.........................8O-33
SEAT BELT SWITCH - DESCRIPTION.....8O-46
SEAT BELT SWITCH - DIAGNOSIS AND
TESTING...........................8O-47
SEAT BELT SWITCH - OPERATION.......8O-46
SEAT BELT TENSION REDUCER -
DESCRIPTION.......................8O-48
SEAT BELT TENSION REDUCER -
DIAGNOSIS AND TESTING.............8O-49
SEAT BELT TENSION REDUCER -
OPERATION.........................8O-49
SEAT BELT TENSIONER - DESCRIPTION . . . 8O-47
SEAT BELT TENSIONER - OPERATION....8O-48
SEAT BELT TURNING LOOP ADJUSTER -
INSTALLATION......................8O-50
SEAT BELT TURNING LOOP ADJUSTER -
REMOVAL..........................8O-50
SEAT CUSHION / COVER - FRONT -
INSTALLATION.......................23-83
SEAT CUSHION / COVER - FRONT -
REMOVAL..........................23-83
SEAT CUSHION / COVER - REAR -
INSTALLATION.......................23-85
SEAT CUSHION / COVER - REAR -
REMOVAL..........................23-85
SEAT CUSHION - INSTALLATION,
CENTER............................23-80
SEAT CUSHION - REMOVAL, CENTER.....23-80
SEAT CUSHION COVER - INSTALLATION,
CENTER............................23-81
SEAT CUSHION COVER - REMOVAL,
CENTER............................23-81
SEAT CUSHION FRAME - REAR -
INSTALLATION.......................23-85
SEAT CUSHION FRAME - REAR -
REMOVAL..........................23-85
SEAT ELEMENT - DESCRIPTION, HEATED . . 8G-5
SEAT ELEMENT - DIAGNOSIS AND
TESTING, HEATED.....................8G-6
SEAT ELEMENT - INSTALLATION,
HEATED.............................8G-6
SEAT ELEMENT - OPERATION, HEATED....8G-6
SEAT ELEMENT - REMOVAL, HEATED.....8G-6
SEAT MODULE - DESCRIPTION, HEATED . . . 8E-6
SEAT MODULE - DIAGNOSIS AND
TESTING, HEATED.....................8E-7
SEAT MODULE - INSTALLATION, HEATED . . . 8E-7
SEAT MODULE - OPERATION, HEATED.....8E-6
SEAT MODULE - REMOVAL, HEATED......8E-7
SEAT SENSOR - DESCRIPTION, HEATED . . . 8G-7
SEAT SENSOR - DIAGNOSIS AND
TESTING, HEATED.....................8G-7
SEAT SENSOR - OPERATION, HEATED.....8G-7
SEAT SENSOR - REMOVAL, HEATED......8G-7
SEAT STORAGE BIN - INSTALLATION,
UNDER............................23-81
SEAT STORAGE BIN - REMOVAL, UNDER . . 23-81
SEAT STORAGE BIN COVERING -
INSTALLATION, UNDER................23-81
SEAT STORAGE BIN COVERING -
REMOVAL, UNDER...................23-81
SEAT STORAGE BIN LATCH -
INSTALLATION, UNDER................23-81
SEAT STORAGE BIN LATCH - REMOVAL,
UNDER............................23-81
SEAT SWITCH - DESCRIPTION, DRIVER . . . 8N-15
SEAT SWITCH - DESCRIPTION, HEATED . . . 8G-7
SEAT SWITCH - DESCRIPTION,
PASSENGER........................8N-16
SEAT SWITCH - DIAGNOSIS AND
TESTING, DRIVER....................8N-15
SEAT SWITCH - DIAGNOSIS AND
TESTING, HEATED.....................8G-8
SEAT SWITCH - DIAGNOSIS AND
TESTING, PASSENGER................8N-17
SEAT SWITCH - INSTALLATION, DRIVER . . 8N-16
SEAT SWITCH - INSTALLATION, HEATED
. . . 8G-9
SEAT SWITCH - INSTALLATION,
PASSENGER
........................8N-18
SEAT SWITCH - OPERATION, DRIVER
....8N-15
SEAT SWITCH - OPERATION, HEATED
.....8G-8
SEAT SWITCH - OPERATION,
PASSENGER
........................8N-17SEAT SWITCH - REMOVAL, DRIVER......8N-16
SEAT SWITCH - REMOVAL, HEATED.......8G-9
SEAT SWITCH - REMOVAL, PASSENGER . . 8N-17
SEAT SYSTEM - DESCRIPTION, HEATED . . . 8G-3
SEAT SYSTEM - DIAGNOSIS AND
TESTING, HEATED.....................8G-4
SEAT SYSTEM - DIAGNOSIS AND
TESTING, POWER....................8N-14
SEAT SYSTEM - OPERATION, HEATED.....8G-4
SEAT TRACK - DESCRIPTION, POWER....8N-18
SEAT TRACK - DIAGNOSIS AND
TESTING, POWER....................8N-18
SEAT TRACK - INSTALLATION...........23-83
SEAT TRACK - INSTALLATION, POWER . . . 8N-19
SEAT TRACK - OPERATION, POWER.....8N-18
SEAT TRACK - REMOVAL..............23-83
SEAT TRACK - REMOVAL, POWER.......8N-19
SEATBELT INDICATOR - DESCRIPTION....8J-34
SEATBELT INDICATOR - OPERATION......8J-34
SEATS - CLEANING, INTAKE/EXHAUST
VALVES ............................9-248
SEATS - DESCRIPTION, INTAKE/
EXHAUST VALVES . 9-122,9-246,9-27,9-305,9-375
SEATS - DESCRIPTION, POWER.........8N-14
SEATS - INSPECTION, INTAKE/EXHAUST
VALVES ............................9-248
SEATS - INSTALLATION, INTAKE/
EXHAUST VALVES...........9-123,9-248,9-29
SEATS - OPERATION, POWER............8N-14
SEATS - REMOVAL, INTAKE/EXHAUST
VALVES ...................9-122,9-248,9-28
SECONDARY CATCH - INSTALLATION,
LATCH STRIKER.....................23-48
SECONDARY CATCH - REMOVAL, LATCH
STRIKER...........................23-48
SECTION IDENTIFICATION AND
INFORMATION - DESCRIPTION........8W-01-6
SECURITY INDICATOR - DESCRIPTION....8J-34
SECURITY INDICATOR - OPERATION.....8J-35
SECURITY SYSTEM, DIAGNOSIS AND
TESTING - VEHICLE THEFT..............8Q-3
SELECTION - STANDARD PROCEDURE,
HEAD GASKET.......................9-330
SELECTOR INDICATOR - DESCRIPTION,
GEAR..............................8J-26
SELECTOR INDICATOR - OPERATION,
GEAR..............................8J-27
SELECTOR SWITCH - DESCRIPTION....21-685,
21-719
SELECTOR SWITCH - OPERATION......21-685,
21-719
SENDING UNIT / SENSOR -
DESCRIPTION, FUEL LEVEL........14-68,14-7
SENDING UNIT / SENSOR -
INSTALLATION, FUEL LEVEL.............14-8
SENDING UNIT / SENSOR - OPERATION,
FUEL LEVEL.....................14-68,14-7
SENDING UNIT / SENSOR - REMOVAL,
FUEL LEVEL..........................14-7
SENSE - DESCRIPTION, IGNITION
CIRCUIT............................8E-10
SENSE - OPERATION, IGNITION CIRCUIT . . 8E-12
SENSE - PCM INPUT - OPERATION, ASD
. . . 8I-6
SENSITIVE DEVICES - STANDARD
PROCEDURE, ELECTROSTATIC
DISCHARGE (ESD)
.................8W-01-8
SENSOR - DESCRIPTION, ACCELERATOR
PEDAL POSITION
....................14-25
SENSOR - DESCRIPTION, AMBIENT
TEMP
.............................8M-10
SENSOR - DESCRIPTION, BATTERY
TEMPERATURE
......................8F-21
SENSOR - DESCRIPTION, CAMSHAFT
POSITION
..........................14-82
SENSOR - DESCRIPTION, CAMSHAFT
POSITION
............................8I-8
SENSOR - DESCRIPTION, CRANKSHAFT
POSITION
.....................14-26,14-83
SENSOR - DESCRIPTION, ENGINE
COOLANT TEMPERATURE
...............7-44
SENSOR - DESCRIPTION, FRONT WHEEL
SPEED
..............................5-41
SENSOR - DESCRIPTION, FUEL LEVEL
SENDING UNIT
..................14-68,14-7
SENSOR - DESCRIPTION, FUEL
PRESSURE
.........................14-72
SENSOR - DESCRIPTION, HEATED SEAT
. . . 8G-7SENSOR - DESCRIPTION, INLET AIR
TEMPERATURE SENSOR/PRESSURE......14-90
SENSOR - DESCRIPTION, INPUT SPEED . 21-558
SENSOR - DESCRIPTION, INTAKE AIR
TEMPERATURE......................14-36
SENSOR - DESCRIPTION, INTAKE AIR
TEMPERATURE SENSOR/MAP...........14-93
SENSOR - DESCRIPTION, KNOCK........8I-25
SENSOR - DESCRIPTION, LINE
PRESSURE (LP)....................21-559
SENSOR - DESCRIPTION, MAP.....14-39,14-94
SENSOR - DESCRIPTION, MODE . . 21-684,21-718
SENSOR - DESCRIPTION, OUTPUT
SPEED............................21-567
SENSOR - DESCRIPTION, OXYGEN.......14-43
SENSOR - DESCRIPTION, POSITION....21-618,
21-654
SENSOR - DESCRIPTION, SPEED . 21-254,21-431
SENSOR - DESCRIPTION, THROTTLE
POSITION..........................14-52
SENSOR - DESCRIPTION,
TRANSMISSION RANGE . . 21-263,21-441,21-581
SENSOR - DESCRIPTION,
TRANSMISSION TEMPERATURE . 21-267,21-445,
21-583
SENSOR - DESCRIPTION, WATER IN
FUEL..............................14-77
SENSOR - DIAGNOSIS AND TESTING,
AMBIENT TEMPERATURE..............8M-11
SENSOR - DIAGNOSIS AND TESTING,
HEATED SEAT ........................8G-7
SENSOR - DIAGNOSIS AND TESTING,
REAR WHEEL SPEED..................5-43
SENSOR - INSTALLATION,
ACCELERATOR PEDAL POSITION........14-25
SENSOR - INSTALLATION, BATTERY
TEMPERATURE......................8F-21
SENSOR - INSTALLATION, CAMSHAFT
POSITION..........................14-83
SENSOR - INSTALLATION, CAMSHAFT
POSITION...........................8I-14
SENSOR - INSTALLATION, CRANKSHAFT
POSITION.....................14-30,14-84
SENSOR - INSTALLATION, ENGINE
COOLANT TEMPERATURE...............7-47
SENSOR - INSTALLATION, FRONT
WHEEL SPEED........................5-42
SENSOR - INSTALLATION, FUEL LEVEL
SENDING UNIT.......................14-8
SENSOR - INSTALLATION, FUEL
PRESSURE.........................14-72
SENSOR - INSTALLATION, INLET AIR
TEMPERATURE SENSOR/PRESSURE......14-90
SENSOR - INSTALLATION, INPUT SPEED . 21-559
SENSOR - INSTALLATION, INTAKE AIR
TEMPERATURE......................14-38
SENSOR - INSTALLATION, INTAKE AIR
TEMPERATURE SENSOR/MAP...........14-94
SENSOR - INSTALLATION, KNOCK........8I-26
SENSOR - INSTALLATION, LINE
PRESSURE (LP)....................21-560
SENSOR - INSTALLATION, MAP.........14-42
SENSOR - INSTALLATION, OUTPUT
SPEED............................21-567
SENSOR - INSTALLATION, OXYGEN......14-45
SENSOR - INSTALLATION, POSITION....21-619,
21-654
SENSOR - INSTALLATION, REAR WHEEL
SPEED..............................5-43
SENSOR - INSTALLATION, THROTTLE
POSITION..........................14-54
SENSOR - INSTALLATION,
TRANSMISSION RANGE........21-266,21-444
SENSOR - OPERATION, ACCELERATOR
PEDAL POSITION....................14-25
SENSOR - OPERATION, AMBIENT TEMP . . 8M-10
SENSOR - OPERATION, BATTERY
TEMPERATURE......................8F-21
SENSOR - OPERATION, CAMSHAFT
POSITION
..........................14-82
SENSOR - OPERATION, CAMSHAFT
POSITION
............................8I-8
SENSOR - OPERATION, CRANKSHAFT
POSITION
.....................14-26,14-83
SENSOR - OPERATION, ENGINE
COOLANT TEMPERATURE
...............7-44
SENSOR - OPERATION, FRONT WHEEL
SPEED
..............................5-41
30 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

SENSOR - OPERATION, FUEL LEVEL
SENDING UNIT..................14-68,14-7
SENSOR - OPERATION, FUEL PRESSURE . . 14-72
SENSOR - OPERATION, HEATED SEAT.....8G-7
SENSOR - OPERATION, INLET AIR
TEMPERATURE SENSOR/PRESSURE......14-90
SENSOR - OPERATION, INPUT SPEED . . . 21-558
SENSOR - OPERATION, INTAKE AIR
TEMPERATURE......................14-36
SENSOR - OPERATION, INTAKE AIR
TEMPERATURE SENSOR/MAP...........14-93
SENSOR - OPERATION, KNOCK..........8I-25
SENSOR - OPERATION, LINE PRESSURE
(LP)..............................21-559
SENSOR - OPERATION, MAP...........14-39
SENSOR - OPERATION, MODE . . . 21-684,21-718
SENSOR - OPERATION, OUTPUT SPEED . . 21-567
SENSOR - OPERATION, OXYGEN........14-43
SENSOR - OPERATION, POSITION......21-619,
21-654
SENSOR - OPERATION, SPEED . . . 21-254,21-431
SENSOR - OPERATION, THROTTLE
POSITION..........................14-52
SENSOR - OPERATION, TRANSMISSION
RANGE................21-263,21-441,21-581
SENSOR - OPERATION, TRANSMISSION
TEMPERATURE.........21-267,21-445,21-583
SENSOR - OPERATION, WATER IN FUEL . . 14-78
SENSOR - REMOVAL, ACCELERATOR
PEDAL POSITION....................14-25
SENSOR - REMOVAL, BATTERY
TEMPERATURE......................8F-21
SENSOR - REMOVAL, CAMSHAFT
POSITION..........................14-83
SENSOR - REMOVAL, CAMSHAFT
POSITION...........................8I-11
SENSOR - REMOVAL, CRANKSHAFT
POSITION.....................14-29,14-84
SENSOR - REMOVAL, ENGINE COOLANT
TEMPERATURE.......................7-44
SENSOR - REMOVAL, FRONT WHEEL
SPEED..............................5-41
SENSOR - REMOVAL, FUEL LEVEL
SENDING UNIT.......................14-7
SENSOR - REMOVAL, FUEL PRESSURE . . . 14-72
SENSOR - REMOVAL, HEATED SEAT......8G-7
SENSOR - REMOVAL, INLET AIR
TEMPERATURE SENSOR/PRESSURE......14-90
SENSOR - REMOVAL, INPUT SPEED.....21-559
SENSOR - REMOVAL, INTAKE AIR
TEMPERATURE......................14-36
SENSOR - REMOVAL, INTAKE AIR
TEMPERATURE SENSOR/MAP...........14-93
SENSOR - REMOVAL, KNOCK...........8I-25
SENSOR - REMOVAL, LINE PRESSURE
(LP)..............................21-559
SENSOR - REMOVAL, MAP.............14-40
SENSOR - REMOVAL, OUTPUT SPEED . . . 21-567
SENSOR - REMOVAL, OXYGEN..........14-44
SENSOR - REMOVAL, POSITION . . 21-619,21-654
SENSOR - REMOVAL, REAR WHEEL
SPEED
..............................5-42
SENSOR - REMOVAL, THROTTLE
POSITION
..........................14-53
SENSOR - REMOVAL, TRANSMISSION
RANGE
......................21-265,21-443
SENSOR - REMOVAL, WATER IN FUEL
....14-78
SENSOR CIRCUIT - DIAGNOSIS AND
TESTING, AMBIENT TEMPERATURE
......8M-11
SENSOR RETURN - DESCRIPTION
.......8E-10
SENSOR (TRS) - DIAGNOSIS AND
TESTING, TRANSMISSION RANGE
......21-264,
21-442
SENSOR/MAP SENSOR - DESCRIPTION,
INTAKE AIR TEMPERATURE
............14-93
SENSOR/MAP SENSOR - INSTALLATION,
INTAKE AIR TEMPERATURE
............14-94
SENSOR/MAP SENSOR - OPERATION,
INTAKE AIR TEMPERATURE
............14-93
SENSOR/MAP SENSOR - REMOVAL,
INTAKE AIR TEMPERATURE
............14-93
SENSOR/PRESSURE SENSOR -
DESCRIPTION, INLET AIR
TEMPERATURE
......................14-90
SENSOR/PRESSURE SENSOR -
INSTALLATION, INLET AIR
TEMPERATURE
......................14-90SENSOR/PRESSURE SENSOR -
OPERATION, INLET AIR TEMPERATURE . . . 14-90
SENSOR/PRESSURE SENSOR -
REMOVAL, INLET AIR TEMPERATURE....14-90
SENSOR/SWITCH - DESCRIPTION, OIL
PRESSURE..........................9-66
SENSOR/SWITCH - INSTALLATION, OIL
PRESSURE.....................9-343,9-67
SENSOR/SWITCH - OPERATION, OIL
PRESSURE..........................9-66
SENSOR/SWITCH - REMOVAL, OIL
PRESSURE.....................9-343,9-67
SENTRY KEY IMMOBILIZER MODULE -
DESCRIPTION.......................8E-13
SENTRY KEY IMMOBILIZER MODULE -
INSTALLATION.......................8E-15
SENTRY KEY IMMOBILIZER MODULE -
OPERATION.........................8E-13
SENTRY KEY IMMOBILIZER MODULE -
REMOVAL..........................8E-15
SENTRY KEY IMMOBILIZER SYSTEM
INDICATOR LAMP - DESCRIPTION........8Q-5
SENTRY KEY IMMOBILIZER SYSTEM
INDICATOR LAMP - OPERATION..........8Q-5
SENTRY KEY IMMOBILIZER SYSTEM
INITIALIZATION, STANDARD
PROCEDURE.........................8Q-3
SENTRY KEY IMMOBILIZER SYSTEM
(SKIS), DESCRIPTION..................8Q-1
SENTRY KEY IMMOBILIZER SYSTEM
TRANSPONDER PROGRAMMING,
STANDARD PROCEDURE...............8Q-4
SEPARATOR - DESCRIPTION, FUEL
FILTER / WATER .....................14-61
SEPARATOR - INSTALLATION, FUEL
FILTER / WATER .....................14-62
SEPARATOR - OPERATION, FUEL FILTER
/ WATER ...........................14-61
SEPARATOR - REMOVAL, FUEL FILTER /
WATER.............................14-61
SERVO - ASSEMBLY, FRONT.....21-209,21-388
SERVO - ASSEMBLY, REAR......21-253,21-430
SERVO - CLEANING, FRONT.....21-208,21-388
SERVO - CLEANING, REAR......21-252,21-430
SERVO - DESCRIPTION.................8P-6
SERVO - DESCRIPTION, FRONT . . 21-207,21-387
SERVO - DESCRIPTION, REAR . . . 21-252,21-429
SERVO - DISASSEMBLY, FRONT . . 21-208,21-388
SERVO - DISASSEMBLY, REAR . . . 21-252,21-430
SERVO - INSPECTION, FRONT . . . 21-208,21-388
SERVO - INSTALLATION................8P-7
SERVO - OPERATION..................8P-7
SERVO - OPERATION, FRONT....21-208,21-387
SERVO - OPERATION, REAR.....21-252,21-429
SERVO - REMOVAL....................8P-7
SETTING TRANSMITTER CODES -
STANDARD PROCEDURE..............8M-12
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT
TO GROUND ON FUSES POWERING . . . 8W-01-10
SHAFT - ASSEMBLY, PLANETARY
GEARTRAIN/OUTPUT...........21-245,21-423
SHAFT - CAUTION, HALF................3-11
SHAFT - DESCRIPTION, PLANETARY
GEARTRAIN/OUTPUT...........21-242,21-420
SHAFT - DIAGNOSIS AND TESTING,
HALF...............................3-11
SHAFT - DIAGNOSIS AND TESTING,
PROPELLER...........................3-1
SHAFT - DISASSEMBLY, PLANETARY
GEARTRAIN/OUTPUT...........21-243,21-421
SHAFT - INSPECTION, PLANETARY
GEARTRAIN/OUTPUT...........21-245,21-422
SHAFT - INSTALLATION, BALANCE........9-79
SHAFT - INSTALLATION, FRONT
PROPELLER...........................3-7
SHAFT - INSTALLATION, HALF...........3-12
SHAFT - INSTALLATION, IDLER.....9-175,9-80
SHAFT - INSTALLATION, REAR
PROPELLER...........................3-8
SHAFT - OPERATION, PLANETARY
GEARTRAIN/OUTPUT...........21-243,21-420
SHAFT - REMOVAL, BALANCE...........9-79
SHAFT - REMOVAL, FRONT PROPELLER
....3-6
SHAFT - REMOVAL, HALF
...............3-11
SHAFT - REMOVAL, IDLER
.........9-175,9-79
SHAFT - REMOVAL, REAR PROPELLER
.....3-7
SHAFT - SPECIAL TOOLS, HALF
..........3-12SHAFT - SPECIAL TOOLS, PROPELLER.....3-6
SHAFT - SPECIFICATIONS, HALF..........3-12
SHAFT - SPECIFICATIONS, PROPELLER.....3-6
SHAFT - STANDARD PROCEDURE,
PROPELLER...........................3-3
SHAFT FRONT BEARING -
INSTALLATION, OUTPUT........21-217,21-395
SHAFT FRONT BEARING - REMOVAL,
OUTPUT.....................21-217,21-395
SHAFT REAR BEARING - INSTALLATION,
OUTPUT.....................21-217,21-396
SHAFT REAR BEARING - REMOVAL,
OUTPUT.....................21-217,21-395
SHAFT SEAL - INSTALLATION, FRONT
OUTPUT.........21-618,21-653,21-683,21-717
SHAFT SEAL - INSTALLATION, STEERING
GEAR INPUT........................19-28
SHAFT SEAL - REMOVAL, FRONT
OUTPUT.........21-617,21-653,21-683,21-717
SHAFT SEAL - REMOVAL, STEERING
GEAR INPUT........................19-25
SHAFT SEALS - INSTALLATION, AXLE . 3-33,3-58,
3-84
SHAFT SEALS - REMOVAL, AXLE . 3-33,3-58,3-84
SHAFTS - ASSEMBLY, AXLE.............3-58
SHAFTS - DISASSEMBLY, AXLE..........3-56
SHAFTS - INSTALLATION, AXLE....3-111,3-138,
3-33,3-58,3-83
SHAFTS - REMOVAL, AXLE . . . 3-111,3-138,3-33,
3-56,3-83
SHIELD - INSTALLATION, FRONT
WHEELHOUSE SPLASH.................23-41
SHIELD - INSTALLATION, REAR
WHEELHOUSE SPLASH................23-41
SHIELD - REMOVAL, FRONT
WHEELHOUSE SPLASH................23-40
SHIELD - REMOVAL, REAR
WHEELHOUSE SPLASH................23-41
SHIELDS - DESCRIPTION, HEAT..........11-7
SHIELDS - INSTALLATION, HEAT.........11-8
SHIELDS - REMOVAL, HEAT.............11-7
SHIFT BOOT - INSTALLATION, 4WD
FLOOR.............................23-64
SHIFT BOOT - REMOVAL, 4WD FLOOR....23-63
SHIFT COVER - INSTALLATION....21-128,21-86
SHIFT COVER - REMOVAL.......21-128,21-86
SHIFT INTERLOCK - ADJUSTMENTS,
BRAKE TRANSMISSION . . 21-195,21-376,21-540
SHIFT INTERLOCK - DIAGNOSIS AND
TESTING, BRAKE TRANSMISSION......21-195,
21-375,21-540
SHIFT INTERLOCK SYSTEM -
DESCRIPTION, BRAKE TRANSMISSION . . 21-194,
21-375,21-540
SHIFT INTERLOCK SYSTEM -
OPERATION, BRAKE TRANSMISSION....21-194,
21-375,21-540
SHIFT LEVER - ADJUSTMENT....21-622,21-657
SHIFT LEVER - INSTALLATION . . . 21-621,21-656
SHIFT LEVER - INSTALLATION, GEAR.....19-12
SHIFT LEVER - REMOVAL.......21-620,21-655
SHIFT LEVER - REMOVAL, GEAR........19-12
SHIFT MECHANISM - DESCRIPTION....21-253,
21-430,21-574
SHIFT MECHANISM - INSTALLATION.....21-85
SHIFT MECHANISM - OPERATION......21-253,
21-430,21-574
SHIFT MECHANISM - REMOVAL.........21-84
SHIFT MOTOR - DESCRIPTION . . . 21-686,21-720
SHIFT MOTOR - INSTALLATION . . 21-686,21-720
SHIFT MOTOR - OPERATION.....21-686,21-720
SHIFT MOTOR - REMOVAL......21-686,21-720
SHOCK - DIAGNOSIS AND TESTING . . . 2-23,2-35
SHOCK - DIAGNOSIS AND TESTING,
SPRING.............................2-38
SHOCK - INSTALLATION............2-35,2-40
SHOCK - REMOVAL................2-35,2-40
SHOES - ADJUSTMENT, PARKING BRAKE . . 5-34
SHOES - INSTALLATION................5-34
SHOES - REMOVAL
....................5-33
SHORT TO GROUND - STANDARD
PROCEDURE, TESTING FOR A
........8W-01-9
SHORT TO GROUND ON FUSES
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A
..........................8W-01-10
SIDE - INSTALLATION, LEFT
............9-122
SIDE - INSTALLATION, RIGHT
...........9-121
DRINDEX 31
Description Group-Page Description Group-Page Description Group-Page