2003 DAEWOO MATIZ airbag

9E–12 INSTRUMENTATION/DRIVER INFORMATION
DAEWOO M-150 BL2
D19B515A
Installation Procedure
1. Connect the electrical connector and the speedom-
eter cable.
2. Install the instrument cluster assembly to instrument
panel with screws.
3. Install the instrument cluster trim panel to the instru-
ment panel. Refer to “Instrument Cluster Trim Pan-
el” in this section.
4. Connect the negative battery cable.
D109B516
INSTRUMENT PANEL
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the driver’s airbag module from the steer-
ing wheel. Refer to Section 8B, Supplemental Inflat-
able Restraints (SIR) (For the vehicle equipped with
the airbag).
3. Remove the steering wheel from the steering col-
umn. Refer to Section 6E, Steering Wheel and Col-
umn.
4. Remove the steering column trim cover. Refer to
Section 6E, Steering Wheel and Column.
5. Remove the signal lamp switch and the wiper
switch. Refer to Section 6E, Steering Wheel and
Column.
6. Pry off the A–pillar trim panels. Refer to Section 9G,
Interior Trim.
7. Remove the instrument cluster trim panel from the
instrument panel.

Remove the screws (1)

Using a flathead screwdriver, remove the instru-
ment cluster trim panel (2).
Notice: To prevent the instrument panel damage, cover
the flathead screwdriver with a soft cloth.
D109B517
8. Remove the hood latch release lever from the in-
strument panel. Refer to Section 9R, Body Front
End.
9. Remove the glove box assembly from the instru-
ment panel. Refer to “Glove Box” in this section.
10. Remove the passenger’s airbag module from the in-
strument panel. Refer to Section 8B, Supplemental
Inflatable Restraints (SIR) (For vehicle equipped
with the airbag).
11. Put aside the floor console after removing the
screws (1).

9E–14 INSTRUMENTATION/DRIVER INFORMATION
DAEWOO M-150 BL2
7. Install the instrument cluster assembly. Refer to “In-
strument Cluster” in this section.
8. Install the floor console with the screws.
9. Install the passenger’s airbag module to the instru-
ment panel. Refer to Section 8B, Supplemental In-
flatable Restraints (SIR) (For vehicle equipped with
the airbag).
10. Install the glove box assembly to the instrument
panel. Refer to “Glove Box” in this section.
11. Install the hood latch release lever to the instrument
panel. Refer to Section 9R, Body Front End.
12. Install the instrument cluster trim panel to the instru-
ment cluster trim panel with the screws.
13. Install the A–pillar trim panels. Refer to Section 9G,
Interior Trim.
14. Install the signal lamp switch and the wiper switch.
Refer to Section 6E, Steering Wheel and Column.
15. Install the steering column trim cover. Refer to Sec-
tion 6E, Steering Wheel and Column.
16. Install the steering wheel to the steering column.
17. Install the driver’s airbag module to the steering
wheel. Refer to Section 8B, Supplemental Inflatable
Restraints (SIR) (For vehicle equipped with the air-
bag).
18. Connect the negative battery cable.
D109B522
TIE–BAR
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the instrument panel assembly. Refer to “In-
strument Panel” in this section.
3. Remove the defroster duct hose from the tie–bar.

Remove the screws (1).

Remove the defroster duct hose (2).
D19B547A
4. Remove the nuts and the steering column. Refer to
Section 6E, Steering Wheel and Column.
5. Disconnect the electrical connectors and electrical
wiring harness after removing the electrical wiring
harness strips.

Remove the electrical wiring harness strip.

Disconnect the brake switch connector (1).

Disconnect the thermostat connector (2).

Disconnect the blow motor connector (3).

Disconnect the blow motor resistance connector
(4).

Disconnect the electrical wiring harness (5).

INSTRUMENT/DRIVER INFORMATION 9E–17
DAEWOO M-150 BL2
D109B702
4. Remove the passenger’s airbag module blank cover
from the instrument panel.

Remove the screws.

Remove the passenger’s airbag module blank cov-
er (1).
D109B703
5. Remove the ventilation duct from the instrument pan-
el.

Remove the screws.

Remove the ventilation duct (1).
D109B704
6. Remove the ventilation grilles from the instrument
panel.

Remove the screws.

Remove the ventilation grilles (1).
D109B705
7. Remove the cigar lighter housing from the instrument
panel.

Remove the screws.

Remove the cigar lighter housing (1).

INSTRUMENT/DRIVER INFORMATION 9E–19
DAEWOO M-150 BL2
D19B710A
7. Install the passenger’s airbag module blank cover to
the instrument panel with the screws.
Tighten
Tighten the screws to 1.5–2 N.m (13–18 lb-in).
a. Passenger’s airbag module blank cover screw
8. Install the instrument cluster brackets to the instru-
ment panel with the screws.
9. Install the instrument panel assembly. Refer to “In-
strument Panel” in this section.
10. Connect the negative battery cable.
D109B711
INSTRUMENT CLUSTER INDICATOR
LAMPS
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the instrument cluster from the instrument
panel. Refer to “Instrument Cluster” in this section.
3. Remove the indicator bulbs from the rear of the clus-
ter.
D109B712
Installation Procedure
1. Install the indicator bulb.
2. Install the instrument cluster to the instrument panel.
Refer to “Instrument Cluster” in this section.
3. Connect the negative battery cable.
D109B713
SPEEDOMETER/ODOMETER/TRIP
ODOMETER
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the instrument cluster from the instrument
panel. Refer to “Instrument Cluster” in this section.
3. Remove the instrument cluster lens and the face
plate.
a. Window plate.

9E –22 INSTRUMENT/DRIVER INFORMATION
DAEWOO M-150 BL2
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS

Application

Nm

Lb-Ft

Lb-In
Passenger’s Airbag Module Blank Cover Screw

1.5–2

–

13–18
INSTRUMENT CLUSTER INDICATOR LAMPS SPECIFICATIONS
Indicator Lamp Color Bulb
ABS Warning Amber 14 v 1.4 W
Airbag Warning Red 14 v 1.4 W
Battery Charge Indicator Red 14 v 1.4 W
Fasten Seat Belt Warning Red 14 v 1.4 W
High Beam Indicator Blue 14 v 1.4 W
Low Fuel Level Warning Amber 12 v 3 W Oil Pressure Warning Red 14 v 1.4 W Parking Brake Indicator and Brake Fluid Warning Red 14 v 1.4 W Service Engine Soon Warning Amber 14 v 1.4 W
Turn Signal Indicators

Green

14 v 1.4 W
Instrument Cluster IlluminationBlue12 v 3 W
Rear Fog Lamp IndicatorAmber14 v 1.4 W

9G –2 INTERIOR TRIM
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
INTERIOR TRIM PANELS
The interior trim panels are molded plastic and fasten
with screws or plastic clips.
PRESSURE RELIEF VENT
When all the windows are closed and the ventilation sys-
tem is on, the addition of outside air to the interior of the
vehicle causes a positive pressure within the vehicle. In
order to relieve the pressure, air is released through one
pressure relief vents. The pressure relief vent is located
in the luggage compartment, behind the spare wheel.
FLOOR CONSOLE
The floor console fits over the tunnel in the floor of the
vehicle and extends from under the center of the instru-
ment panel to the front seat area. The floor console con-
tains the transaxle shift lever and a cupholder.
The sensing and diagnosis module (SDM) for the airbag
system is located under the floor console.
PARKING BRAKE CABLE COVER
The parking brake cable cover should be removed to ad-
just the free play of the parking brake cable.
FLOOR CARPET
The molded one-piece floor carpet goes over both the
front and the rear floor pans.