2003 DAEWOO MATIZ power steering

POWER STEERING PUMP 6B–5
DAEWOO M-150 BL2
D105C527
PUMP DRIVE PULLEY
Tools Required
DW310–020 Power Steering Pulley Remove Holder
Removal Procedure
1. Remove the front passenger side headlamp.
Refer to Section 9B, Lighting Systems.
2. Remove the steering pump pulley.

Remove the pump drive belt. Refer to “Pump Drive
Belt” in this section.

Fix the pulley using the power steering pulley re-
move holder DW310–020 (1).

Remove the pump drive pulley nut (2).
55–69 Nm
D15C528A
Installation Procedure
1. Install the pump drive pulley. Install the steering pump
pulley nut.
2. Install the pump drive belt.
3. Tighten the steering pump pulley nut using the power
steering pulley remove holder DW310–020.
Tighten
Tighten the steering pump pulley nuts to 55–69 Nm
(41–51 lb-ft).
4. Install the front passenger side headlamp.
Refer to Section 9B, Lighting Systems.
D105C529
PUMP ASSEMBLY
Removal Procedure
1.Remove the front passenger side headlamp.
Refer to Section 9B, Lighting Systems.
2. Disconnect the pipe line from the pump.

Disconnect the supply line pipe hose (1).

Disconnect the pressure line pipe fitting (2).
D105C530
3. Remove the power steering pump.

Remove the pump drive belt. Refer to “Pump Drive
Belt” in this section.

Disconnect the power steering pressure switch
connector (1). Refer to Section 6A, Power Steering
Systems.

Remove the bolts (2).

6B –6 POWER STEERING PUMP
DAEWOO M-150 BL2
D105C531

Remove the bolt (3).
18–22 Nm
D15C532A
Installation Procedure
1. Install the power steering pump with the bolt.
Tighten
Tighten the bolt to 18–22 Nm (13–16 lb-ft).
2. Connect the power steering pressure switch connec-
tor. Refer to Section 6A, Power Steering System.
3. Install the pump drive belt. Refer to “Pump Drive Belt”
in this section.
20–24 Nm
20–24 Nm 21–35 Nm
D15C533A
4. Install the bolts.
Tighten

Tighten the rear bracket adjusting bolt to 20–24
Nm (15–18 lb-ft) (1).

Tighten the power steering bolt to 20–24 Nm
(15–18 lb-ft) (2).
5. Connect the pressure line pipe to the outlet connec-
tion on the steering pump.
Tighten
Tighten the pressure line pipe fitting to 21–35 Nm
(16–26 lb-ft) (3).
6. Install the front passenger side headlamp.
Refer to Section 9B, Lighting Systems.
Notice: When adding fluid or making a complete fluid
change, always use DEXRON-II or DEXRON-III pow-
er steering fluid. Failure to use the proper fluid will cause
hose and seal damage and fluid leaks.
7. Refill the pump with new fluid and bleed the air from
the system. Refer to Section 6A, Bleeding the Power
Steering System.
8. Inspect for leaks. If leaks are found, correct the cause
of the leak and bleed the system.

POWER STEERING PUMP 6B–7
DAEWOO M-150 BL2
UNIT REPAIR
PUMP
The power steering pump in this vehicle is not service-
able. A faulty pump must be replaced.

6B –8 POWER STEERING PUMP
DAEWOO M-150 BL2
SPECIFICATIONS
GENERAL SPECIFICATIONS

Application

Description
Lubricant

Power Steering Fluid DEXRON-II, DEXRON-III
Capacity

1.0 Liter (1.056 qt)
Type

Vane
FASTENER TIGHTENING SPECIFICATIONS
Application Nm Lb-Ft Lb-In
Power Steering Pump Bolt 20 – 24 15 – 18 –
Power Steering Pump Front Bracket Bolt 20 – 24 15 – 18 –
Power Steering Pump Front Bracket Adjusting Bolt 18 – 22 13 – 16 –
Power Steering Pump Rear Bracket Upper Bolt 35 – 45 26 – 33 –
Power Steering Pump Rear Bracket Lower Bolt 20 – 24 15 – 18 –
Power Steering Pump Rear Bracket Adjusting Bolt20 – 2415 – 18–
Power Steering Pump Pulley Nut55 – 6941– 51–
Power Steering Oil Pressure Line Fitting21 – 3516 – 26–

POWER STEERING PUMP 6B–9
DAEWOO M-150 BL2
SPECIAL TOOLS AND EQUIPMENT
SPECIAL TOOLS TABLE
D105C101
DW310–020
Power Steering Pulley
Remove Holder

DAEWOO M-150 BL2
SECTION 6C
POWER STEERING GEAR
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise
noted.
TABLE OF CONTENTS
Description and Operation 6C-2. . . . . . . . . . . . . . . . . .
Power Rack and Pinion 6C-2. . . . . . . . . . . . . . . . . . . .
Diagnostic Information and Procedures 6C-3. . . . .
Power Rack and Pinion Steering Gear 6C-3. . . . . . .
Adjust the Free Load of the Steering Gear 6C-5. . .
Repair Instructions 6C-6. . . . . . . . . . . . . . . . . . . . . . . . .
On-Vehicle Service 6C-6. . . . . . . . . . . . . . . . . . . . . . . . . .
Rack and Pinion Assembly 6C-6. . . . . . . . . . . . . . . . .
Power Steering Gear Rack and Pinion Boot 6C-7. . . Unit Repair 6C-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tie Rod End Boot 6C-8. . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic Cylinder Lines 6C-8. . . . . . . . . . . . . . . . . . . .
Rack and Pinion Steering Gear 6C-9. . . . . . . . . . . . . .
Assembly
Specifications 6C-13. . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Specifications 6C-13. . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specifications 6C-13. . . . . . . . . .

6C – 2 POWER STEERING GEAR
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
POWER RACK AND PINION
The power rack and pinion steering system has a rotary
control valve which directs the hydraulic fluid coming
from the hydraulic pump to one side or the other side of
the rack piston. The integral rack piston is attached to
the rack. The rack piston converts hydraulic pressure to
a linear force which moves the rack left or right. The
force is then transmitted through the tie rods and the tierod ends to the steering knuckles, which turn the
wheels.
If hydraulic assist is not available, manual control is
maintained. However, under these conditions, more
steering effort is required. The movement of the steering
wheel is transferred to the pinion. The movement of the
pinion is then transferred through the pinion teeth, which
meshs with the teeth on the rack, causing the rack to
move.

POWER STEERING GEAR 6C–3
DAEWOO M-150 BL2
DIAGNOSTIC INFORMATION AND PROCEDURES
POWER RACK AND PINION STERING GEAR
ConditionProbable CauseCorrection
Hissing Noise
Loose steering coupling joints.
Tighten the steering coupling
joints.

Improperly contacted the power
steering hose with other
components.
Fit the power steerng hose into
the hose clips correctly.
Rattling Noise in Steering Gear
Improperly contacted the power
steering line with the body.
Fix the steering line correctly.

Insufficient lubricant.
Lubricate the steering gear.

Loose steering gear mounting.
Tighten the steering gear
mounting bracket bolts.

Improperly installed tie rod ends.
Tighten the tie rod joints and
replace the tie rod end as needed.
Poor Return of Steering Wheel
to Center
Improperly contacted the steering
wheel with the turn signal housing.
Adjust the turn signal housing.

Improper binding or looseness of
steering coupling.
Replace the intermediate shaft.

Stuck and improperly aligned
power steering pump flow control
valve.
Replace the power steering pump.

Improper binding or looseness of
tie rods and ball joints.
Tighten the tie rods and the ball
joints. Replace the tie rods and
the ball joints as needed.

Poor adjustments of the steering
gear.
Perform a straight-ahead check.
Momentary Increase in Effect
When Turning the Wheel
Internal leaks of the power
steering pump.
Replace the power steering pump.
Quickly
The damage or restricted flow of
the hoses.
Replace the power steering hoses
and pipes.

Insufficient power steering fluid.
Fill the power steering fluid
reservoir.

Stuck and improperly operated
power steering pump flow control
valve.
Replace the power steering pump.
Steering Surges or Jerks When
Turning with Engine Running
Insufficient pressure of the power
steering pump.
Replace the power steering pump.

Stuck and improperly operated
power steering pump flow control
valve.
Replace the power steering pump.

The slippage of the pump drive
belt.
Tighten the pump drive belt.

Contaminated air in the power
steering system.
Bleed the power steering system.