2003 DAEWOO MATIZ ECO mode

IMMOBILIZER ANTI-THEFT SYSTEM 9T–21
DAEWOO M–150 BL2
P 1628 – ECM Immobilizer Error (No Successful Communication)
StepActionValueYesNo
1
Connect the scan tool using the following procedure:
1. Insert the cartridge into the scan tool.
2. Turn the ignition switch to the OFF position.
3. Connect the scan tool to the data link connector
(DLC).
4. Connect the scan tool’s power cord to the cigar
lighter socket.
5. Select immobilizer mode on the scan tool.
6. Turn the ignition ON, but do not start the engine.
Is communication established between the scan tool
and the immobilizer control unit?
–
Go to Step 2
Go to
“Communi-
cation
Between
Immobilizer
and Test
Equipment”
2
Read the IMMO & ECM ID CODE message that
was displayed after requesting DIAGNOSIS.
Did the message differ from normal message?
Normal Message –ECM MODE: LEARNT
IMMO. MODE: LEARNT
VIN CODE: SAME
–
Go to
“Identification
(ID) Code
Repro-
gramming”
Go to Step 3
3
Check for an open serial data wire between the
immobilizer control unit and the ECM.
Was the circuit open?
–
Go to Step 4Go to Step 5
4
Repair the open serial data wire between the ECM
and the immobilizer control unit.
Is the repair complete?
–
System OK
–
5
1. Replace the immobilizer.
2. Reprogram the identification (ID) code. Refer to
“Identification (ID) Code Reprogramming” in this
section.
Is the repair complete?
–
System OK
–
Go to Step 6
6
1. Replace the ECM.
2. Turn the ignition ON, OFF for more than 4
seconds.
3. Turn the ignition ON.
Is the repair complete?
–
System OK
–

IMMOBILIZER ANTI-THEFT SYSTEM 9T–23
DAEWOO M–150 BL2
P 1629 – ECM Immobilizer Error (Incorrect Answer)
StepActionValueYesNo
1
Connect the scan tool using the following procedure:
1. Insert the cartridge into the scan tool.
2. Turn the ignition switch to the OFF.
3. Connect the scan tool to the data link connector
(DLC).
4. Connect the scan tool’s power cord to the cigar
lighter socket.
5. Turn the ignition ON, but do not start the engine.
Is communication established between the scan tool
and the immobilizer control unit?
–
Go to Step 2
Go to
“Communi-
cation
Between
Immobilizer
and Test
Equipment”
2
1. Select DIAGNOSIS from the scan tool menu.
2. Read the IMMO & ECM ID CODE (immobilization
and electronic control module identification code)
message.
Did the message differ from normal message?
Normal Message –ECM MODE: LEARNT
IMMO. MODE: LEARNT
VIN CODE: SAME
–Go to
“Identification
(ID) Code
Repro-
gramming”
Go to Step 3
3
1. Replace the ECM.
2. Reprogram the ID code.
Is the repair complete?
–
System OK
–
Go to Step 4
4
1. Replace the ECM.
2. Turn the ignition ON, OFF for more than 4
seconds.
3. Turn the ignition ON.
Is the repair complete?
–
System OK
–

9T–26 IMMOBILIZER ANTI-THEFT SYSTEM
DAEWOO M–150 BL2
REPAIR INSTRUCTIONS
ON-VEHICLE SERVICE
KEY CODING PROCEDURE
1. Install the immobilizer control unit cartridge in the
scan tool.
2. Turn the ignition OFF
3. Connect the scan tool.
4. Turn the ignition ON with the key to be coded.
5. Enter the four-digit password that enables service
personnel to use the scan tool for coding keys.
6. A lost key can be deleted only by deleting all keys
and reauthorizing the remaining keys as new keys.
If a key is lost, go to the next step. If no keys have
been lost but an additional key is desired, go to Step
8.
7. Use the scan tool command DELETE ALL KEY
CODES.
8. Use the scan tool command AUTHORIZE ONE
ADDITIONAL KEY.
9. Repeat Steps 4, 5, and 6 until the immobilizer con-
trol unit has recorded all of the new keys or, after a
deletion, has reauthorized all of the remaining keys.
The immobilizer control unit can record a maximum
of five keys.
10. Return the system to the normal mode.
11. Turn OFF the ignition.
12. Turn ON the ignition.
13. Crank to start the engine.
ID CODE REPROGRAMMING
Reprogram the identification (ID) code in the following
situations:

An immobilizer control unit has been replaced.

An electronic control module (ECM) has been re-
placed.
If a valid key has been lost, refer to “Key Coding Proce-
dure” in this section.
Reprogramming Procedure
1. Turn the ignition OFF. Reprogramming is not allowed
while the engine is running.
2. Insert the immobilizer control unit cartridge into the
scan tool.
3. Do not start the vehicle, but turn the ignition ON.
4. Enter the four-digit password that enables service
personnel to use the scan tool for ID code reprogram-
ming.
5. Use the scan tool to command RESET ID CODE.