2003 DAEWOO MATIZ turn signal

DAEWOO M-150 BL2
SECTION 9B
LIGHTING SYSTEMS
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise
noted.
TABLE OF CONTENTS
Description and Operation 9B-2. . . . . . . . . . . . . . . . . .
Headlamps and Parking Lamps 9B-2. . . . . . . . . . . . .
Front Turn Signal Lamps 9B-2. . . . . . . . . . . . . . . . . . .
Rear Fog Lamp 9B-2. . . . . . . . . . . . . . . . . . . . . . . . . . .
Taillamps 9B-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
License Plate Lamp 9B-2. . . . . . . . . . . . . . . . . . . . . . . .
Interior Courtesy Lamp 9B-2. . . . . . . . . . . . . . . . . . . . .
Backup Lamp(s) 9B-2. . . . . . . . . . . . . . . . . . . . . . . . . . .
Daytime Running Lamps (DRL)
(W/Europe Only) 9B-2. . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Information and Procedures 9B-3. . . . .
Headlamps 9B-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn Signal Lamps and Hazard Lamps 9B-4. . . . . . .
Stoplamps and Interior Courtesy Lamp 9B-5. . . . . . .
Rear Fog Lamp 9B-6. . . . . . . . . . . . . . . . . . . . . . . . . . .
Repair Instructions 9B-7. . . . . . . . . . . . . . . . . . . . . . . . .
Headlamps 9B-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn Signal Lamps 9B-8. . . . . . . . . . . . . . . . . . . . . . . .
Side Turn Signal Lamps 9B-8. . . . . . . . . . . . . . . . . . . .
Taillamps Assembly 9B-9. . . . . . . . . . . . . . . . . . . . . . . .
Front Fog Lamp 9B-9. . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Fog/Backup Lamp(s) 9B-10. . . . . . . . . . . . . . . . .
Center High-Mounted Stoplamp 9B-11. . . . . . . . . . . . CHMSL Mounting Bracket 9B-12. . . . . . . . . . . . . . . . .
License Plate Lamps 9B-12. . . . . . . . . . . . . . . . . . . . . .
Door Jamb Switch 9B-13. . . . . . . . . . . . . . . . . . . . . . . .
Interior Courtesy Lamp 9B-13. . . . . . . . . . . . . . . . . . . .
Daytime Running Lamp Module
(W/Europe Only) 9B-14. . . . . . . . . . . . . . . . . . . . . . .
Ashtray Lamp 9B-14. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Luggage Room Lamp 9B-15. . . . . . . . . . . . . . . . . . . . .
Specifications 9B-16. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bulb Usage Chart 9B-16. . . . . . . . . . . . . . . . . . . . . . . .
Schematic and Routing Diagrams 9B-17. . . . . . . . . .
Backup Lamp(s) Circuit 9B-17. . . . . . . . . . . . . . . . . . .
Headlamps Circuit 9B-18. . . . . . . . . . . . . . . . . . . . . . . .
Headlamp Leveling Circuit 9B-19. . . . . . . . . . . . . . . . .
Tail and Licence Plate Lamps Circuit 9B-20. . . . . . . .
Stoplamps Circuit 9B-21. . . . . . . . . . . . . . . . . . . . . . . .
Turn and Hazard Lamps Circuit 9B-22. . . . . . . . . . . .
Interior Courtesy Lamp Circuit 9B-23. . . . . . . . . . . . . .
Front Fog Lamp Circuit 9B-24. . . . . . . . . . . . . . . . . . . .
Rear Fog Lamp Circuit 9B-25. . . . . . . . . . . . . . . . . . . .
Dimmer Control Circuit (Except W/Europe) 9B-26. .
Daytime Running Lamps Circuit
(W/Europe Only) 9B-27. . . . . . . . . . . . . . . . . . . . . . .

9B – 2 LIGHTING SYSTEMS
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
HEADLAMPS AND PARKING LAMPS
The headlamps are controlled by the multifunction lever
located on the left side of the steering column. They will
come on with the ignition switch in any position. Turning
the headlamp switch to the first position turns on the
parking lamps, the license plate lamps and the instru-
ment panel illumination. Turning the switch to the sec-
ond position turns on all of the previous lamps and the
headlamps. Turning the switch to the off position turns
off all the lamps.
The parking lamps can be turned on by turning the light-
ing switch to the first position. The parking lamps can be
turned off by turning the switch to the OFF position.
Headlamp high beam and low beam are also controlled
by this lever. When the headlamps are on, pushing the
lever away from the driver until the switch clicks
changes the lamp from low beam to high beam. An indi-
cator lamp on the instrument cluster assembly will come
on when the high beam headlamps are on. To return the
headlamps to low beam, pull the lever toward the driver.
The headlamps must be aimed for proper illumination of
the road. Headlamp aim should be checked whenever a
new headlamp assembly is installed or service repairs to
the front end area may have disturbed the headlamp as-
sembly or its mountings.
FRONT TURN SIGNAL LAMPS
When the turn signals are activated, the side turn signal
lamps flash to signal a turn. The turn signal works only
when the ignition switch is on.
The turn signals are controlled by the light switch on the
left side of the steering column. Moving the lever all the
way up or down (past the detent) will turn on the turn sig-
nals. When the turn is completed, the lever will return to
horizontal and the turn signals will stop flashing.
For changing lanes or shallow turns where the steering
wheel does not turn far enough to cancel the signal,
move the signal only to the first detent and hold it there.
When the lever is released, it will return to horizontal and
the turn signal will cancel.
REAR FOG LAMP
The rear fog lamp is incorporated in the drive side tail-
lamp assembly and are controlled by the rear fog lamp
switch on the instrument panel. The rear fog lamp can
be turned on only when headlamps are on.
TAILLAMPS
The taillamps, stoplamps, backup lamp(s), rear fog lamp
(if equipped with) and turn signal lamps are one assem-
bly.
Turning on either the headlamps or the parking lamps
will also turn on the taillamps. When the brake pedal is
pushed, the taillamps will glow brighter to serve as sto-
plamps.
The center high-mounted stoplamp is located in the rear
window and will come on when the brake pedal is
pressed.
LICENSE PLATE LAMPS
The license plate lamps will come on when the head-
lamps or the parking lamps are on. The license plate
lamps are mounted on the rear bumper, above the li-
cense plate.
INTERIOR COURTESY LAMP
The courtesy lamp is located on the headliner just be-
fore the front seats. The lamp switch has three posi-
tions. If the switch is in the center position, the lamp will
go on whenever a door is opened and go off when it is
closed. In the ON position, the lamp will stay on until it is
turned off. In the OFF position, the lamp will not come
on, even when a door is opened.
BACKUP LAMP(S)
The backup lamps are located in the rear combination
lamps. They will come on when the transaxle is shifted
into REVERSE. On a vehicle with a manual transaxle,
they are activated by a reverse switch which is part of
the transaxle.
DAYTIME RUNNING LAMPS (DRL)
(W/Europe Only)
The daytime running lamps (DRL) work in conjunction
with the exterior lamps system. When the ignition switch
is turned to the ”II” position with the light switch off, park-
ing, tail, license plate and instrument panel lights illumi-
nate. And, when the engine is started, the headlamps
(low beam) also come on.
They remain on until the ignition switch is turned off or
the light switch is turned on. They revert to normal op-
eration when the light switch is on.
The daytime running lamps (DRL) is optional.

9B–4 LIGHTING SYSTEMS
DAEWOO M-150 BL2
TURN SIGNAL LAMPS AND HAZARD LAMPS
ConditionProbable CauseCorrection
Turn Signal Lamps and Hazard
Lamps Do Not Work.
The open circuit or a short circuit
between the power supply circuit
and the fuse Ef2.
Repair or Replace the wiring
harness.

Fuse Ef2 is blown.
Replace the fuse Ef2.

The open circuit or a short circuit
between the fuse Ef2 and the fuse
F12.
Repair of Replace the wiring
harness.

Fuse F12 is blown.
Replace the fuse F12.

The open circuit or a short circuit
between the fuse F12 and the
terminal 8 of the hazard lamp
switch connector.
Repair or Replace the wiring
harness.

Faulty hazard lamp switch.
Replace the hazard lamp switch.

The open circuit or a short circuit
between the terminal 7 of the
hazard lamp switch connector and
the terminal 49 of the turn signal
lamp relay.
Repair or Replace the wiring
harness.

The open circuit or a short circuit
between the terminal 49a of the
turn signal lamp relay and the
terminal 9 of the hazard lamp
switch connector.
Repair or Replace the wiring
harness.

Faulty turn signal lamp relay.
Replace the turn signal lamp relay.

The open circuit or a short circuit
between the terminal 49a of the
turn signal lamp relay and the
terminal 2 of the turn signal lamp
switch connector.

Faulty turn signal lamp switch.
Replace the turn signal lamp
switch.

The open circuit or a short circuit
between the terminal 1,3 of the
turn signal switch connector and
the terminal 2,5 of each turn signal
lamp connectors.
Repair or Replace the wiring
harness.

Turn signal lamp bulb is blown.
Replace the turn signal lamp bulb.

The open grounds (G101, G102,
G401, G402) circuits.
Repair or Replace the open
ground circuit.
Hazard Lamps Do Not Operate,
Turn Signals Are OK.
The open circuit or a short circuit
between the terminal 49a of the
turn signal lamp relay and the
terminal 9 of the hazard lamp
switch connector.
Repair or Replace the open
circuit.

The open circuit or a short circuit
between the terminals 5,6 of the
hazard lamp switch connector and
the terminals 2,5 of the turn signal
lamp connectors.
Repair or Replace the wiring
harness.

9B–8 LIGHTING SYSTEMS
DAEWOO M-150 BL2
D19D505A
TURN SIGNAL LAMPS
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the front bumper spacer. Refer to Section
9M, Exterior Trim.
3. Remove the turn signal lamps from the front bumper
spacer.

Disconnect the electrical connector (1).

Remove the screw (2).

Remove the turn signal lamp assembly (3).
D19D506A
Installation Procedure
1. Connect the electrical connector.
2. Install the turn signal lamp assembly with the screw.
3. Install the front bumper spacer. Refer to Section 9M,
Exterior Trim.
4. Connect the negative battery cable.
D29B001
SIDE TURN SIGNAL LAMPS
Removal Procedure
1. Disconnect the negative battery cable.
2. Slide the side turn signal lamp rearward.
3. Remove the lamp.
4. Disconnect the electrical connector.
D29B002
Installation Procedure
1. Connect the electrical connector.
2. Install the side turn signal lamp.
3. Connect the negative battery cable.

9B–16 LIGHTING SYSTEMS
DAEWOO M-150 BL2
SPECIFICATIONS
BULB USAGE CHART
BulbReplacement Bulb Number
Backup Lamp(s)21W
Center High Mounted Stoplamp21W
HeadlampsDouble 60/55W
Interior Courtesy Lamp10W
License Plate Lamp5W
Front Turn Signal Lamps21W
Rear Fog Lamp21W
Rear Turn Signal Lamps21W
Side Marker Turn Signal Lamps5W
Tail and StoplampDouble 5/21W, 5W
Parking Lamp5W

9E –22 INSTRUMENT/DRIVER INFORMATION
DAEWOO M-150 BL2
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS

Application

Nm

Lb-Ft

Lb-In
Passenger’s Airbag Module Blank Cover Screw

1.5–2

–

13–18
INSTRUMENT CLUSTER INDICATOR LAMPS SPECIFICATIONS
Indicator Lamp Color Bulb
ABS Warning Amber 14 v 1.4 W
Airbag Warning Red 14 v 1.4 W
Battery Charge Indicator Red 14 v 1.4 W
Fasten Seat Belt Warning Red 14 v 1.4 W
High Beam Indicator Blue 14 v 1.4 W
Low Fuel Level Warning Amber 12 v 3 W Oil Pressure Warning Red 14 v 1.4 W Parking Brake Indicator and Brake Fluid Warning Red 14 v 1.4 W Service Engine Soon Warning Amber 14 v 1.4 W
Turn Signal Indicators

Green

14 v 1.4 W
Instrument Cluster IlluminationBlue12 v 3 W
Rear Fog Lamp IndicatorAmber14 v 1.4 W

9M –4 EXTERIOR TRIM
DAEWOO M-150 BL2
D19E589A
3. Remove the rear spoiler from the tailgate.

Remove the nuts (1).

Remove the rear spoiler (2).
D19E590A
Installation Procedure
1. Install the rear spoiler on the tailgate with the nuts.
2. Install the spoiler seals.
D209B109
FRONT BUMPER SPACER
Removal Procedure
1. Support the hood suitably.
2. Disconnect the negative battery cable.
3. Remove the front bumper spacer.

Remove the bolts (1).

Remove the front bumper spacer from the bumper
fascia (2).
4. Remove the turn signal lamps. Refer to Section 9B,
Lighting Systems.
D209B110
Installation Procedure
1. Install the turn signal lamps. Refer to Section 9B,
Lighting Systems.
2. Install the front bumper spacer with the bolts.
3. Connect the negative battery cable.

9T–2 REMOTE KEYLESS ENTRY AND ANTI-THEFT SYSTEM
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
REMOTE KEYLESS ENTRY AND
ANTI-THEFT SYSTEM
The remote keyless entry and anti-theft system can per-
form the following functions:

Remotely lock and unlock the vehicle doors with a
hand-held high-frequency transmitter.

Sense intrusion into the vehicle through the doors,
the tailgate, or the hood.

Activate a warning to signal an intrusion.

Help the driver find the vehicle in a parking area.

Automatically re-lock the doors if a door or the trunk is
not opened within 30 seconds after the vehicle has
been unlocked by the remote keyless entry.

Communicate serial data to a scan tool to help diag-
nose system faults.
The remote keyless entry and anti-theft system consists
of the following components:

Keyless entry and anti-theft control module/receiver.

Security indicator.

Tailgate open switch.

Door open switches.

Central locking unit.

Flashing turn signal lamps.

Siren.

Hood open switch.
REMOTE LOCKING AND UNLOCKING
The hand-held transmitter locks and unlocks the vehicle
doors by sending radio waves to the control module/re-
ceiver in the vehicle. The effective range of the transmit-
ter varies between 5 and 10 meters (approximately 16 to
32 feet), depending on whether or not objects such as
other vehicles are blocking the path of the radio waves.
The transmitter has a LOCK button and an UNLOCK
button which only function when the ignition is OFF.
Pressing the UNLOCK button has the following effects:

The doors are unlocked.

The turn signal lamps flash twice.

The control module is disarmed.
Pressing the LOCK button has the following effects:

The doors are locked.

The turn signal lamps flash once.

The control module is armed.
The transmitter has a replaceable battery. The battery is
designed to last at least two years before replacement is
necessary.
SECURITY INDICATOR
There is a security indicator on the instrument panel. Af-
ter the LOCK button of the transmitter is pressed, the
module is placed in the armed mode, and the security
indicator flashes. The security indicator turns ON for 1/8
second and OFF for 7/8 second. It then flashes at that
frequency until the control module/receiver is disarmed.
INTRUSION SENSING
The anti-theft function is armed if the transmitter sends
the LOCK message to the control module/receiver when
the ignition is OFF.
When the hood, the door, or the tailgate is opened, the
hood open switch, the door open switch, or the tailgate
open switch will change its input to ground. The alarm
will be activated if the hood open sensor, the door open
sensor, or the tailgate open sensor changes its input to
ground before either of the following conditions occurs:

An UNLOCK message is received from the transmit-
ter.
SIREN
The remote keyless entry system is armed when the
LOCK message is received from the transmitter when
the ignition is OFF. When the system is armed, it will ac-
tivate the siren and flash the turn signals for 28 seconds
if any of the following conditions occurs:

A door is opened (front door open switch input is
changed to ground).

The tailgate is opened (tailgate open switch input is
changed to ground).

The hood is opened while the anti-theft system is
armed (hood open switch input is changed to
ground).
The siren is disarmed when any of the following condi-
tions occurs:

The ignition switch is turned ON with the key.

The UNLOCK button or the LOCK button on the re-
mote transmitter is pressed.
VEHICLE LOCATOR
The remote keyless entry system assists the driver in lo-
cating the vehicle. When the vehicle is unlocked with the
remote control, the turn signals flash twice to indicate
the location of the vehicle. The duration of the flashes
and the length of time between flashes is used to indi-
cate certain vehicle conditions. Refer to “Fault or Alarm
Indication” in this section.