2002 YAMAHA TW200 Owners Manual

6-35
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EAU01260
Troubleshooting chartEW000125
w
Never check the fuel system while smoking or in the vicinity of an open flame.
1. Fuel
2. Compression
3. Ignition
4. Battery
Use electric starter.
Remove spark
There is compression.
Go to ignition check.
No compression.
Ask a Yamaha dealer to inspect.
Wet
DryWipe clean with dry cloth and correct
Open the throttle half-way and start
Ask a Yamaha dealer to inspect.
Check if there is fuel
Enough fuel
No fuelGo to compression check.
Supply fuel.
in the fuel tank
electrode. plugs and check
Engine doesn’t start, go to battery
check. the engine. spark plug gap or replace spark plugs.
Engine turns over
Engine turns overBattery good.
Check fluid, recharge,
quickly.
slowly. check connections.Engine doesn’t start, ask aYamaha dealer to inspect.
Engine doesn’t start, go to compression check.
5FY-9-E0 (TW200) 7/29/02 10:54 AM Page 64

7-1
EAU01010
CLEANING AND STORAGE
1
2
3
4
5
6
7
8
9
EAU01301A. CLEANING
Frequent, thorough cleaning of
your motorcycle will not only
enhance its appearance but will
improve its
general performance and extend
the useful life of many compo-
nents.
ECA00002
cC
8Improper cleaning can damage
the cowlings, panels and other
plastic parts. Use only a soft,
clean cloth or sponge with
mild detergent and water to
clean plastic.
8Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abra-
sive cleaning products, solvent
or thinner, fuel (gasoline), rust
removers or inhibitors, brake
fluid, antifreeze or electrolyte.
EC000111
cC
Excessive hose pressure may
cause water seepage and deterio-
ration of wheel bearings, front
fork, brakes, transmission seals
and electrical parts.
Many expensive repair bills have
resulted from improper high pres-
sure detergent applications such
as those available in coin-operated
car washers.
4. After riding on salted roads,
wash the motorcycle with cold
water immediately. Do not use
warm water as it increases the
chemical reaction of the salt.
5. Once the majority of the dirt
has been hosed off, wash all
surfaces with warm water and
mild, detergent-type soap. An
old toothbrush or bottle brush
is handy for hard-to-get-at
places. 1. Before cleaning the motorcy-
cle:
a. Block off the end of the
exhaust pipe to prevent water
entry; a plastic bag and strong
rubber band may be used.
b. Make sure the spark plug and
all filler caps are properly
installed.
2. If the engine case is excessive-
ly greasy, apply degreaser
with a paint brush. Do not
apply degreaser to the chain,
sprockets or wheel axles.
3. Rinse the dirt and degreaser
off with a garden hose. Use
only enough pressure to do
the job.
5FY-9-E0 (TW200) 7/29/02 10:54 AM Page 65

7-2
CLEANING AND STORAGE
1
2
3
4
5
6
7
8
96. Rinse the motorcycle off
immediately with clean water
and dry all surfaces with a
chamois, clean towel, or soft
absorbent cloth.
7. Dry the chain and lubricate it
to prevent rust.
8. Clean the seat with a vinyl
upholstery cleaner to keep the
cover pliable and glossy.
9. Automotive-type wax may be
applied to all painted and
chrome-plated surfaces. Avoid
combination cleaner-waxes.
Many contain abrasives which
may mar the paint or protec-
tive finish. When finished, start
the engine and let it idle for
several minutes.
EAU01107B. STORAGE
Long term storage (60 days or
more) of your motorcycle will
require some preventive proce-
dures to guard against deteriora-
tion. After thoroughly cleaning the
motorcycle, prepare for storage as
follows:
1. Fill the fuel tank with fuel and
add fuel stabilizer (if available).
2. Remove the spark plug, pour
about one tablespoon of SAE
10W30 or 20W40 motor oil in
the spark plug hole and rein-
stall the spark plug. Turn the
engine over several times
(ground spark plug lead) to
coat the cylinder wall with oil.
EW000127
w
When using the starter motor to
crank the engine, remove the
spark plug wires, and ground them
to prevent sparking.
3. Thoroughly clean and lubricate
the drive chain. (For details,
see “Drive chain lubrication”
on page 6-23.)
4. Lubricate all control cables.
5. Block up the frame to raise
both wheels off the ground.
6. Tie a plastic bag over the
exhaust pipe outlet to prevent
moisture from entering.
7. If storing in a humid or salt-air
atmosphere, coat all exposed
metal surfaces with a light film
of oil. Do not apply oil to any
rubber parts or the seat cover.
8. Remove the battery and
charge it. Store it in a dry place
and recharge it once a month.
Do not store the battery in an
excessively warm or cold place
(less than 0°C or more than
30°C.
NOTE:
Make any necessary repairs before
storing the motorcycle.
5FY-9-E0 (TW200) 7/29/02 10:54 AM Page 66

8-1
EAU01038
SPECIFICATIONS
1
2
3
4
5
6
7
8
9
Specifications
Model TW200E
Dimensions:
Overall length 2,090 mm
Overall width 815 mm
Overall height 1,115 mm
Seat height 790 mm
Wheel base 1,325 mm
Ground clearance 250 mm
Minimum turning radius 1,900 mm
Basic weight (With oil and full
fuel tank):126 kg
Engine:
Engine type Air-cooled 4-stroke, SOHC,
gasoline
Cylinder arrangement Forward inclined
single cylinder
Displacement 196 cm
3
Bore ×Stroke 67.0 ×55.7 mm
Compression ratio 9.5:1
Starting system Electric and kick starter
Lubrication system Wet sumpEngine oil:
Type:
Classification API Service “SE”, “SF” type
or equivalent
(e.g. “SF-SE”, “SF-SE-CC”,
“SF-SE-SD” etc.)
Capacity:
Periodic oil change 1.0 L
With oil filter replacement 1.1 L
Total amount 1.3 L
Air filter:Wet type element
Fuel:
Type Regular gasoline
Fuel tank capacity 7.0 L
Reserve amount 1.7 L
Carburetor:
Type / quantity Y29P-5C / 1
Manufacturer TEIKEI
–10° 0° 10° 20° 30° 40°
SAE 10W/30
SAE 10W/40
SAE 20W/40
SAE 20W/50C
5FY-9-E0 (TW200) 7/29/02 10:54 AM Page 67

8-2
EAU01038
SPECIFICATIONS
1
2
3
4
5
6
7
8
9
Spark plug:
Type / Manufacturer D8EA / NGK or
X24ES-U / DENSO
Spark plug gap 0.6 ~ 0.7 mm
Clutch type:Wet, multiple-disc
Transmission:
Primary reduction system Spur gear
Primary reduction ratio 3.318
Secondary reduction system Chain drive
Secondary reduction ratio 3.571
Number of sprocket teeth
(Rear/Front) 50/14
Transmission type Constant mesh 5-speed
Operation Left foot operation
Gear ratio 1st 2.833
2nd 1.789
3rd 1.318
4th 1.040
5th 0.821
Chassis:
Frame type Diamond
Caster angle 26.5°
Trail 94 mmTire:
Type With tube
Size:
Front 130/80-18 66P
Rear 180/80-14M/C 78P
Manufacturer / model:
Front BRIDGESTONE / TW31
Rear BRIDGESTONE / TW32
Maximum load* 157 kg
Air pressure (cold tire):
up to 80 kg load*
Front 125 kPa; 1.25 kgf/cm
2; 1.25 bar
Rear 125 kPa; 1.25 kgf/cm
2; 1.25 bar
80 kg load ~ Maximum
load*
Front 150 kPa; 1.50 kgf/cm
2; 1.50 bar
Rear 175 kPa; 1.75 kgf/cm
2; 1.75 bar
Off-road riding
Front 125 kPa; 1.25 kgf/cm
2; 1.25 bar
Rear 125 kPa; 1.25 kgf/cm
2; 1.25 bar
High-speed riding
Front 150 kPa; 1.50 kgf/cm
2; 1.50 bar
Rear 175 kPa; 1.75 kgf/cm
2; 1.75 bar
*Load is total weight of cargo, rider, passenger and accessories.
5FY-9-E0 (TW200) 7/29/02 10:54 AM Page 68

8-3
SPECIFICATIONS
1
2
3
4
5
6
7
8
9
Wheels:
Type:
Front Spoke wheel
Rear Spoke wheel
Size:
Front 18 ×2.50
Rear 14M/C ×MT4.50
Brakes:
Front:
Type Drum brake
Operation Right hand operation
Rear:
Type Drum brake
Operation Right foot operation
Suspension:
Front Telescopic fork
Rear Swingarm
(Monocross suspension)
Shock absorber:
Front Coil spring / oil damper
Rear Coil-gas spring / oil damper
Wheel travel:
Front 160 mm
Rear 150 mmElectrical:
Ignition system: C.D.I.
Charging system:
Type A.C. magneto
Standard output 12V 11A / 5,000 rpm
Battery:
Type GM7CZ-3D
Voltage, capacity 12V 7 AH
Headlight typeHalogen bulb
Bulb voltage, wattage ×quantity:
Headlight 12V 35W / 35W ×1
Stop / tail light 12V 27W / 8W ×1
Front flasher light 12V 27W / 8W ×2
Rear flasher light 12V 27W ×2
Meter light 12V 3.4W ×1
Neutral indicator light 12V 3.4W ×1
High beam indicator light 12V 3.4W ×1
Turn indicator light 12V 3.4W ×1
Fuse:
Main 15A
5FY-9-E0 (TW200) 7/29/02 10:54 AM Page 69

8-4
SPECIFICATIONS
1
2
3
4
5
6
7
8
9
EAU01064
HOW TO USE THE CONVERSION TABLE
All specification data in this manual are listed in SI
and METRIC UNITS.
Use this table to convert METRIC unit data to
IMPERIAL unit data.
Ex.
METRIC MULTIPLIER IMPERIAL
** mm×0.03937 = ** in
2 mm×0.03937 = 0.08 inMETRIC TO IMPERIAL
Metric unit Multiplier Imperial unit
m•kg 7.233 ft.lb
Torquem•kg 86.794 in•lb
cm•kg 0.0723 ft•lb
cm•kg 0.8679 in•lb
Weightkg 2.205 lb
g 0.03527 oz
Speed km/hr 0.6214 mph
km 0.6214 mi
m 3.281 ft
Distance m 1.094 yd
cm 0.3937 in
mm 0.03937 in
cc (cm3) 0.03527 oz (IMP liq.)
Volume/ cc (cm3) 0.06102 cu•in
Capacity lt (liter) 0.8799 qt (IMP liq.)
lt (liter) 0.2199 gal (IMP liq.)
kg/mm 55.997 lb/in
Misc. kg/cm
214.2234 psi (lb/in2)Centigrade(°C)9/5 + 32Fahrenheit(°F)
CONVERSION TABLE
5FY-9-E0 (TW200) 7/29/02 10:54 AM Page 70

9-1
EAU01039
CONSUMER INFORMATION
1
2
3
4
5
6
7
8
9
11
EAU01040Identification numbers record
Record the key identification num-
ber, vehicle identification number
and model label information in the
spaces provided for assistance
when ordering spare parts from a
Yamaha dealer or for reference in
case the vehicle is stolen.
1. KEY IDENTIFICATION
NUMBER:
2. VEHICLE IDENTIFICATION
NUMBER:
3. MODEL LABEL INFORMATION:
1. Key identification number 1. Vehicle identification number
EAU01042
Key identification number
The key identification number is
stamped on the key.
Record this number in the space
provided and use it for reference
when obtaining a new key.
EAU01043
Vehicle identification
number
The vehicle identification number
is stamped into the steering head
pipe.
Record this number in the space
provided.
NOTE:
The vehicle identification number
is used to identify your motorcycle
and may be used to register your
motorcycle with the licensing
authority in your state.
1
6
5FY-9-E0 (TW200) 7/29/02 10:54 AM Page 71